Bodden-TownConstruction and installation price of cold storageDesign method

there are some unique installation skills when installing the cold storage? The cold storage installed according to these skills is often short in both effect and quality, and the specific installation skills of the cold storage will also make some relatively detailed introduction for you in the following article. When installing the cold storage, you should install it from the corner first. Later according to the height of the cold storage, make a hole in the middle of the insulation board behind the angle iron parts

The efficiency of the compressor is low, and the refrigerating capacity can not meet the load requirements of the warehouse: due to the long-term operation of the compressor, the cylinder sleeve, ring and other parts are seriously worn, the long-term cold storage installation, installation, fruit preservation, medical cold storage and other brand products, the designated products are complete, the quality is guaranteed, and the sealing performance will be reduced accordingly with the increase of the matching clearance, The gas transmission coefficient of the compressor will also be reduced, and the refrigeration capacity will be reduced. When the refrigerating capacity is less than the heat load of the warehouse, the temperature of the warehouse will drop slowly.

Bodden-Town.Does the cable wire meet the parameters? In general, the cold storage needs to use phase electricity.

Judge the operating sound of the compressor, and carefully listen to the operating sound of water pump, cooling tower, compressor, fan and other equipment. In case of abnormal sound, timely warranty is required, so as to avoid greater damage to the compressor due to untimely warranty.

.Panel types of quick freezing warehouse: color plastic steel plate,Bodden-TownHow much is the design and installation of cold storage, salted steel plate, embossed aluminum, etc.

As a coolant, make it evaporate under low pressure and mechanical conditions to absorb the heat in the storage so as to achieve the purpose of cooling.

Simple refrigeration is based on the volatilization of refrigerant in the condenser of the cold storage, so as to cool the refrigerant, and then input the refrigerant into the box or building of the refrigeration equipment to cool the air according to the heat exchanger. This kind of refrigeration has slow cooling speed, large total heat conduction temperature difference and complex system software, so it can only be used in less places,Bodden-TownThere is a cold storage installed there, such as brine ice making and cold storage with constant temperature requirements.

Cold storage has good water tightness. Polyurethane rigid foam has low water absorption, foam holes, disconnected and closed porosity of more than 95%. It is a dense microporous foam material, which is more dense than air surface, and is not easy to permeate. It belongs to hydrophobic materials.

Material requisition for the installation requirements of the assembly fresh-keeping warehouse: according to the engineering design and construction material list the materials shall be sent to the accessories warehouse, and the materials and accessories models shall be carefully checked.

The selection of equipment for the construction of equipment cold storage is closely related to the size, type and budget of the cold storage.

Standard requirements.Compression refrigerator is commonly used,Bodden-TownRefrigeration and fresh-keeping cold storage, which is mainly composed of compressor, condenser, throttle valve and evaporation pipe. According to the way of evaporation pipe device, it can be divided into direct cooling and indirect cooling. Direct cooling the evaporation pipe is installed in the refrigerated warehouse. When the liquid coolant passes through the evaporation pipe, it will directly absorb the heat in the warehouse and cool down.

At ordinary times, users should check the sealing degree of the gap of the cold storage, and notify the cold storage for maintenance in time if damaged parts are found.

The type of cold storage to be built in the type of cold storage should be determined according to the type of circulating goods. For example, the cold storage that only circulates vegetables can only build a fresh-keeping cold storage, while the cold storage with refrigeration + freezing will be built if there are many types of circulating goods and great difference in storage temperature. As for the size of the cold storage, it should be determined according to the type quantity, frequency, cycle, whether to use shelf stacking and so on. For example, for fruits and vegetables packed in cartons, the storage capacity of 280-330kg per cubic meter can be referred to, and the size of cold storage construction can be estimated in combination with the storage capacity rate of about 0.5-0.6.

The medical cold storage has been widely used in the industry. For the use of the medical cold storage project, we must combine the performance of the product and store it according to the temperature and humidity required by the product. The automatic temperature box also needs to be used outside the product cold storage. At the same time, the management personnel must be familiar with the operation steps of the medical cold storage project.

Excellent quality.The spacing of pull rivets at inner and outer corners is 300mm and 200mm respectively; After the polystyrene library is installed, the wall panel joints shall be evenly sealed and decorated with silicone sealant.

Nowadays, the application of fresh-keeping storehouse is more and more extensive. It is closely related to our daily life. Fresh-keeping storehouse is mainly to ensure the freshness of food.

However, long-term continuous operation will inevitably lead to equipment aging, so reasonable maintenance is particularly important.

Bodden-Town.Install the temporary lighting facilities in the warehouse, install and arrange the construction electrical equipment, and do a good job in rain proof, moisture-proof, anti-collision, anti binding and other safety protection.

Panel types of quick freezing warehouse: color plastic steel plate, salted steel plate, stainless steel plate, embossed aluminum, etc.

The foaming technology of polyurethane with strong stability makes it have superior bonding performance. The firm combination of polyurethane rigid foam and carrier layer is the basic premise to ensure the stability of external insulation layer. That is, under the unfavorable local temperature and humidity conditions, it can bear various internal and external combined loads such as wind force, self weight and normal collision