Washington-DCProduct refrigeration equipmentWhat role does it play in the industry?

In fact, there are some unique installation skills when installing the cold storage? The cold storage installed according to these skills is often short in both effect and quality,Washington-DCConstruction of fruit preservation warehouse, and the specific installation skills of the cold storage will also make some relatively detailed introduction for you in the following article. When installing the cold storage, you should install it from the corner first. Later, according to the height of the cold storage, make a hole in the middle of the insulation board behind the angle iron parts

Requirements for the cold storage time of the device: the cold storage of the refrigeration system using ammonia as refrigerant shall be supported in the place with low population density around.

Washington-DC.When the actual scheme is determined, and sometimes different schemes are combined. For example, the shelving, wall and top smooth pipes of the controlled atmosphere storage can be manually combined with the hot gas method. The frost can be manually swept at ordinary times, and the hot gas defrosting can be carried out regularly, so as to thoroughly understand the frost that is not easy to be removed by manual sweeping and the oil accumulation in the pipeline. Cold fan water flushing and hot gas method. Hot air combined with water can be used for defrosting if there is a lot of frost and the controlled atmosphere storage needs to be defrosted frequently.

Technical assurance measures for the installation of cold storage: during production in the production workshop, the production shall be carried out in strict accordance with the operation rules specified in ISO9002 quality operation, self inspection and inspection application shall be carried out to ensure that the factory pass rate is, and unqualified products are not allowed to leave the factory.

.The evaporator surface is too thick or too much dust, and the heat transfer effect decreases: another important reason is that the heat transfer efficiency of evaporator is low, which is mainly caused by excessive frost or excessive dust on the evaporator surface.

The butt joint between the top warehouse plate and the end of the top warehouse plate shall be treated to prevent air leakage and cold running. After all the top warehouse plates are installed, the butt joint shall be filled with foaming material, and the 80mm wide color steel plate shall be sealed at the butt joint with pull riveting.

In the process of realizing your dream, you must remove all the influences. It is very important to recognize that when these beautiful refrigerators are built in the villa room, the collection pit (pool) for flushing (thawing) and drainage should adopt the Countermeasures of avoiding freezing and cleaning and avoiding backflow of water.

The polyurethane insulation board used in the construction of cold storage shall be integral and continuous, and there shall be no joint in the middle. The junction of polyurethane insulation board, top plate and ground shall be made into fillet arc for transition, temperature difference and other main parameters of fresh-keeping warehouse equipment wholesale shall be set according to the specific situation of the frozen warehouse, and the main parameters cannot be changed at will. All kinds of cold storage installation, cold storage construction fruit preservation cold storage, medical cold storage formal qualification, welcome to telephone inquiry, sincerely invite cooperation! The freezer has been customized according to the customer's regulations in the original factory. After mastering the performance parameters of the freezer, set various main parameters on the board.

The equipment is built according to the application requirements of low-temperature distribution. It is reflected in the following 6 points: a low-temperature hall, a closed platform, an electric sliding refrigerated door, and a platform height conditioning equipment (lifting channel) are built to complete & ldquo; Door to door & rdquo; Type loading and unloading operation has become a symbol of modern cold storage.

Standard requirements.Clean and professional cold storage installation cold storage installation, cold storage construction, fruit fresh-keeping cold storage, medical cold storage have stable performance, safety, reliability and maintenance free. The technical level has reached the domestic level and the advanced level of similar international products. If there is a large amount of ice and water, it must be cleaned in time,Washington-DCWhere is a good place to install cold storage, and it must not be knocked during cleaning, so as not to damage the ground and affect the service life of the cold storage.

Polyurethane with good fire resistance and flame retardancy is a kind of refractory and self extinguishing material after adding flame retardant. In case of fire, it can be carbonized, unlike flow burning and flashover like extruded board which can effectively prevent fire spread. In particular, it can be sealed as a whole after systematic fire prevention treatment to form non combustible products.

During the installation of polystyrene storehouse, the Perpendicularity Error of wall plate shall be corrected while the top storehouse plate is installed. The length of the top warehouse plate shall be 10mm shorter than the surface of the wall plate. After the installation of the top warehouse plate, the 10mm gap shall be marked with foaming material to ensure the sealing performance of the warehouse body.

2 - cold storage

Meticulous workmanship.The installation of cold storage board is a link of the cold storage installation project. High price cold storage installation of various specifications, cold storage installation, cold storage construction, fruit preservation cold storage, medical cold storage. Waste merchants, industry, enterprises and power departments are welcome to visit and negotiate! The cold storage body and storage plate include: floor, vertical plate and ceiling plate. The installation of storage plates in different directions and precautions are as follows: enter the construction site, verify the construction situation according to the construction drawings, determine the equipment installation position, and then refer to the following specifications.

Frequently check and acknowledge whether the voltage of the power supply meets the requirements, and the voltage should be 380V & plusmn; 10% (phase line). When the fresh-keeping warehouse equipment is not used for a long time, the main power supply of the fresh-keeping warehouse shall be cut off, and it shall be ensured that the fresh-keeping warehouse equipment is not affected by moisture dust and other substances. The condenser on the refrigeration unit is simply contaminated, and the fresh-keeping warehouse shall be cleaned regularly according to the actual situation. To adhere to outstanding heat transfer.

The ultrasonic town is a patented technology with a shaped energy cover, which increases the effective humidification amount by 50-70% per hour. What are the reasonable aspects of the design of the quick freezing warehouse?

Washington-DC.The new cold storage material is made of rigid polyurethane or polystyrene foam insulation sandwich panel,Washington-DCWhich is good for small installation of cold storage, which is made by high pressure foaming process and can be made into various lengths and specifications to meet the different requirements of the users.

It is suitable for the freezing processing and storage of food, and manual refrigeration to keep the indoor temperature constant. The walls, floors and flat roofs of large cold storages are laid with thermal insulation materials with a certain thickness to reduce the incoming heat from the outside. In order to reduce the absorption of solar radiation, the surface of the external wall of the cold storage is painted white or light color.

However, long-term continuous operation will inevitably lead to equipment aging, so reasonable maintenance is particularly important.