16Mn large diameter thick wall coiled pipeImprove the efficiency of production and processing

The so-called expanding diameter actually belongs to the pressure processing technology that uses hydraulic or mechanical pressure to apply customized to the inside of the steel pipe, so as to expand the steel pipe outward along the radial direction. Mechanical mode is simpler and more efficient than hydraulic mode, so it is more common in practical application. In particular, it is adopted in the very advanced expanding process of several large-diameter straight seam rolling pipelines.

The wall thickness of general coiled pipe is 20mm and the outer diameter is 450-3000mm. It is made of steel plate by direct rolling, welding and forming. The production process of general thick walled coiled pipe can be divided into cold drawing and hot rolling. The production process of cold rolled seamless steel pipe is generally more complex than hot rolling. Roll sizing test shall be carried out for pipe blank first. If there is no response crack on the surface, the round pipe shall be cut by cutting machine, Cut into blanks about meters in length. However, when entering the annealing process, acid shall be used for annealing, and attention shall be paid to whether a large number of bubbles are generated on the surface. If a large number of bubbles are generated, it indicates that the quality of steel pipe can not meet the response standard. In appearance, the cold-rolled seamless steel pipe is shorter than the hot-rolled seamless steel pipe, and its wall thickness is generally smaller than that of the hot-rolled seamless steel pipe, but the surface is brighter than that of the thick wall seamless steel pipe. There is not too much roughness on the surface, and there are not too many burrs in the diameter. The thick wall coiled pipe is a powerful manufacturer quotation, honest operation, genuine and of the same quality. The thick wall coiled pipe is available from stock, with complete specifications,. Docking and strengthening. Coil pipe processing time is short and delivery is fast Low cost. The rolling pipe is mainly used for pipes, billboards, columns, etc.

.The electric contact pressure gauge is used to press down the pressure of the oil cylinder on both sides of the conveyor to ensure the smooth transportation of strip steel.

The detection of thick wall coiled pipe is mainly ultrasonic flaw detector, and the longitudinal weld on the same cylinder section of coiled pipe should not be more than two. Generally, the round pipe shall be cut by a cutter and cut into a blank with a length of about meters. However, when entering the annealing process, acid shall be used for annealing, and attention shall be paid to whether a large number of bubbles are generated on the surface. If a large number of bubbles are generated, the cold-rolled seamless steel pipe is shorter than the hot-rolled seamless steel pipe, and its wall thickness is generally smaller than that of the hot-rolled seamless steel pipe, but the surface is brighter than that of the thick wall seamless steel pipe. There is not too much roughness on the surface, and there are not too many burrs in the diameter. The thick wall coiled pipe is a powerful manufacturer,Q550b thick wall welded pipe, quotation, honest operation, genuine and of the same quality. The thick wall coiled pipe is available from stock, with complete specifications,. The group of butt welds of coiled pipe shall be flush. When the nominal diameter is greater than, back sealing welding shall be carried out in the pipe. During pipe rolling processing, the surface damage of the plate shall be prevented. The factory has perfect steel plate coil, thick wall coil T-shaped welding coil, flaw detection welding coil, 16Mn coil, special-shaped coil and other production lines. It is a coil factory that can produce large coils of various specifications and wall thicknesses. Our thick wall coil and large coil products are sold to large enterprises all over the country and are deeply trusted and praised by customers. Steel plate coil, thick wall coil, coil, t-welded coil, flaw detection welded coil, 16Mn coil and Q345B coil shall be carried out in strict accordance with ISO9001:2000 international quality management standards.

.Meet the following requirements: 1. The longitudinal joint of butt joint shall not be greater than 10% of the wall thickness plus 2mm and shall not be greater than 3mm. 2. The longitudinal joint of joint 200mm away from the pipe end shall not be greater than 2mm. 3. Other parts shall not be greater than 1mm. 4. The vertical deviation between the end face of coiled pipe and the center line shall not be greater than percent of the outer diameter of pipe and shall not be greater than 3mm. The straightness deviation shall not exceed 1mm / m. 5 the weld cannot be double-sided molded coiled pipe. When the nominal diameter is greater than or equal to 600mm, it is recommended to seal and seal in the pipe. In order to obtain better uniform cleanliness and roughness distribution the particle size and proportion design of rinse agent is very important. The roughness is too large, because the cloud path is too deep which may cause the anti-corrosion layer to become thinner at the peak of the cloud path. At the same time, bubbles are easy to form in the process, which seriously affects the performance of the layer.

Material used for steel plate coil: it is required to be explained by the user.

The influence of welding process parameters on welding current mainly includes two aspects: according to the production characteristics of spiral steel pipe, longitudinal circumferential continuous pipe and penstock, and is reformed on the basis of the same specification and model of traditional pipe rolling equipment.

Adopt external control or internal control roll forming.

Weld inspection is necessary to detect the weld quality of steel coil pipe. After welding, all the welds are tested by on-line continuous ultrasonic automatic flaw detector to ensure the NDT coverage of the welds. If there are defects, it will automatically alarm and spray marks, and the production will adjust the process parameters at any time to eliminate the defects in time.

Good reputation.Deviation reel as follows (unit: mm): nominal diameter & amp; amp; lt; 800 800 to 1200 1300 to 1600 1700 to 2400 2600 to 3000 perimeter Deviation & plusmn; 5± 7± 9± 11± 13 ovality is 1% of the outer diameter, 4 6 8 10 and no more than 4 steel plate coils have standards. At present, we carry out construction according to the acceptance of standard GB / t19793-92.

The influence of welding process parameters mainly includes two aspects: according to the production characteristics of spiral steel pipe, the welding current is usually smaller for internal welding and larger for external welding. However, under the condition of large welding current, and the melting amount of welding wire is also the same

Deviation reel as follows (unit: mm): nominal diameter & amp; amp; lt; 800 800 to 1200 1300 to 1600 1700 to 2400 2600 to 3000 perimeter Deviation & plusmn; 5± 7± 9± 11± 13 ovality is 1% of the outer diameter, 4 6 8 10 and no more than 4 steel plate coils have standards. At present, we carry out construction according to the acceptance of standard GB / t19793-92.

Hot rolled steel pipe is a kind of thick wall steel pipe rolled under the condition of heating the steel plate.

Test results.After, we should prevent the surface damage of the plate. The parts with serious scars must be grinded to make transition, and the wall thickness of the grinded part shall not be less than the design wall thickness. Steel rolling pipe is an unconventional pipe, and there is no domestic standard at present. Therefore, the inspection is mainly aimed at the thickness and weld quality.

Raw materials such as ferric chloride are prepared into corrosive solution in proportion. Generally, the production process of thick wall continuous pipe can be divided into cold drawing and hot rolling. The production process of cold rolled seamless steel pipe is generally more complex than that of hot rolling. The pipe blank must first be tested for coil diameter. If there is no response crack on the surface, the round pipe shall be cut into a blank with a length of about m by a cutter, the quality of the steel pipe will not meet the response standard. The appearance of cold-rolled seamless steel pipe is shorter than that of hot-rolled seamless steel pipe, and the wall thickness is generally smaller than that of hot-rolled seamless steel pipe, but the surface is brighter than that of thick wall seamless steel pipe the surface is not too rough, the diameter is not too prickly, and the strength is high. The manufacturer offers, operates in good faith, and has a real price. The same specification, thick wall continuous pipe, spot supply, and complete specifications,. Then, the observed metallographic samples were put into it for deep corrosion. Professional hot rolled steel pipe, large diameter thick wall rolling pipe, thick wall straight seam rolling pipe, steel casing, rolling pipe factory, high price, service, on-site settlement, honest operation! The corroded sample is cleaned in the ultrasonic generator after cleaning, and the powder falling off the sample during ultrasonic cleaning is collected for filtration and drying to obtain the carbide particles falling off the sample after corrosion. The pipe rolling plant will conduct scanning electron microscope and energy spectrum analysis on the cleaned samples and collected carbonization. What is the application of pressure perforation in pipe rolling production?

Sealing and sealing shall be carried out in the pipeline. The wall thickness of general coiled pipe is 20mm and the outer diameter is 450-3000mm. The production process of general thick walled coiled pipe can be divided into cold drawing and hot rolling directly from the production process of steel plate rolling and general thick walled coiled pipe. The production process of cold-rolled seamless steel pipe is generally more complex than hot rolling. Roll sizing test shall be carried out for the pipe blank first. If there is no response crack on the surface, the round pipe shall be cut by cutting machine and cut into a blank with a length of about meters. However, when entering the annealing process, acid shall be used for annealing, and attention shall be paid to whether a large number of bubbles are generated on the surface. If a large number of bubbles are generated, it indicates that the quality of steel pipe can not meet the response standard. In appearance, the cold-rolled seamless steel pipe is shorter than the hot-rolled seamless steel pipe and its wall thickness is generally smaller than that of the hot-rolled seamless steel pipe, but the surface is brighter than that of the thick wall seamless steel pipe. There is not too much roughness on the surface, and there are not too many burrs in the diameter. The thick wall coiled pipe is a powerful manufacturer, quotation, honest operation, genuine and of the same quality. The thick wall coiled pipe is available from stock, with complete specifications,. Welding, forming, butt joint and pipe rolling, with short processing time, fast delivery and low cost, are mainly used for hot-rolled thick wall coils such as pipes, billboard and columns. The thickness of hot-rolled thick wall coils is generally greater than 20mm and the outer diameter is 450-3000mm. The hot-rolled thick wall coils are rolled under the heating of steel plates Welding, forming, deburring, defect detection and delivery. Sometimes the wall thickness is relatively thick and secondary heating is required. The feature is that the outer diameter tolerance is small Uniform wall thickness. It is important that the hot rolled thick wall coil will not damage the properties of raw materials. The disadvantages of hot roll thick wall rolling pipe are long processing time and. Professional hot-rolled steel pipe, large-diameter thick wall coil,Q345B thick wall coiled pipe, thick wall straight seam coil, steel casing, coil factory inspection is strict, quality assurance. Preferential activities are in progress, welcome to consult. Hot-rolled thick wall coil is widely used: cylinder block, hydraulic pressure, bridge, roller table, etc.

.Weight per meter of steel plate coil = (outer diameter wall thickness) * wall thickness * 0.0246615 steel plate coil is made of steel plate. Thick wall t-welded coil can be divided into coil and hot rolled thick wall coil.

The inspection requirements for thick wall coiled pipe treatment are that the thick wall coiled pipe is made of steel plate. The thick wall coiled pipe can be divided into coiled pipe and hot rolled thick wall coiled pipe. Generally, the production process of thick wall coiled pipe can be divided into cold drawing and hot rolling. The production process of cold-rolled seamless steel pipe is generally more complex than hot rolling. Roll sizing test shall be carried out for the pipe blank first. If the surface does not respond to the crack, the round pipe shall be cut by a cutter and cut into a blank with a length of about meters. However, when entering the annealing process, acid shall be used for annealing, and attention shall be paid to whether a large number of bubbles are generated on the surface. If a large number of bubbles are generated, it indicates that the quality of steel pipe can not meet the response standard. In appearance, the cold-rolled seamless steel pipe is shorter than the hot-rolled seamless steel pipe,Q550b large diameter thick wall welded pipe, and its wall thickness is generally smaller than that of the hot-rolled seamless steel pipe, but the surface is brighter than that of the thick wall seamless steel pipe. There is not too much roughness on the surface, and there are not too many burrs in the diameter. The thick wall coiled pipe is a powerful manufacturer, quotation honest operation, genuine and of the same quality. The thick wall coiled pipe is available from stock, with complete specifications,. The wall thickness of coiled pipe is 20mm and the outer diameter is 450-3000mm. It is rolled, welded, formed, butted, removed and reinforced directly from the steel plate. Coil processing time is short and delivery is fast.

Finish machining is performed below, and after shot peening, the scales on the inner and outer surfaces of the elbow are removed