16Mn large diameter thick wall coiled pipeHow to paint to prevent corrosion

Since the groove sizes of longitudinal and circumferential joints of hot-rolled pipes are different, it is necessary to confirm whether the inner side is upward before plate rolling to ensure the correctness of groove direction.

It has advantages and quality. The weld reinforcement obtained is increased, the weld formation is deteriorated and the edge transition is poor.

.Grid.

The steel plate or strip is bent and then welded to form a thick wall coil. According to the welding form, it is divided into straight seam welded pipe and spiral welded pipe. It is divided into ordinary welded pipe, galvanized welded pipe, oxygen blowing welded pipe, wire sleeve, metric welded pipe, rolling pipe, deep well pump pipe, automobile pipe, transformer pipe, welded thin-wall pipe, welded pipe and spiral welded pipe. Coil pipe is dedicated to the production of longitudinal ring coil pipe and steel pressure pipe, and is modified according to similar specifications of traditional rolling equipment. The function of increasing the parameters of spiral steel pipe equipment by 30% fills the gap that the original traditional rolling equipment can not produce. It can produce steel pipes with a diameter of 400 or more and a wall thickness of 8-100mm. The material mainly includes q23 q34 20#,Q460b large diameter reel, 16 manganese, 16 manganese capacity, etc. Product executive standards include: GB / t50205-2001, GB / t3092-2001, etc. The products are widely used in petroleum chemicals, natural gas transportation pile driving, urban water supply, heating, gas supply and other projects.

.When the nominal diameter is larger than the internal seal of the pipe, and when the butt weld is flush with the pipe, it is and coiled pipe. During pipe rolling, the surface of the circuit board shall be protected from damage.

1800mm steel pipe elbow detailed introduction to elbow: first of all, the material is hot pushed, the pusher is a horn shaped core or mandrel, the mandrel is thickened and thickened, the process of pushing the elbow is the process of expanding the diameter, and it is supported on the back. The material tube part passes through the mandrel, others are driven by mechanical transmission, that is, screw drive, and then the car pushes forward and the car pushes the pipeline along the core. The rod moves forward, there is an induction coil outside the mandrel, and then the trolley pushes the tube down and processes one.

The rolling pipe factory mainly produces steel plate rolling pipe and thick wall rolling pipe. With the development of domestic economic situation and the acceleration of welding and casting trend, the advantage of NC cutting is gradually recognized. NC cutting not only greatly improves the rate of plate and product quality, but also improves the working environment and labor efficiency. At present, the CNC cutting machines used in the thick wall rolling pipe processing industry are mainly flame and ordinary plasma cutting machines, but pure flame cutting can not meet the needs of modern production, At present, most CNC cutting machines are CNC plasma cutting machines. This type of cutting machine can meet the needs of thick wall coiled pipe plate processing and thick wall coiled pipe parts processing, so the demand will be greater and greater, but there is still a very obvious gap with foreign countries, mainly in

Pipe rolling is to form the steel pipe blank with a steel plate rolling machine, then weld it into steel pipe with submerged arc welding or electric welding, and then conduct sizing and forming on other forming equipment. This kind of pipe is single piece production with low efficiency, unstable pipe quality and low dimensional accuracy, but the equipment is simple and the investment is less. Longitudinal welded pipe equipment has high efficiency, good quality, high precision and good performance. It is the main equipment for large-scale production of steel pipes.

The welding method of welded steel pipe is submerged arc welding; Molding process, forward swing intermittent production; Unit speed, 0.5 -- 3m / min; Welding speed, 0.5 -- 3m / min. The unit is composed of uncoiler, centering device, hydraulic shear, milling welding machine, disc shear, edge milling machine, plate surface cleaning equipment, delivery machine,Q345B large diameter thick wall coiled pipe, plate edge pre bending equipment, forming machine, internal welding, flash, pulling out, repair welding, flat head chamfering, hydraulic inspection, finished product inspection and degreasing collection. The whole process of submerged arc welding of spiral steel pipe is as follows: the principle of spiral steel pipe submerged arc welding: submerged arc welding is welded with arc heat energy. The difference from manual electrode arc welding is that the welding wire of submerged arc welding is, and there is no coating on it. The flux of submerged arc welding is pre laid at the place to be welded. In the flux of submerged arc welding wire, the arc is under the flux. For welding wire and workpiece, when the start button is pressed, the welding wire and workpiece are energized, the welding wire is pulled back, the arc is ignited, the welding trolley moves forward, and the welding wire is continuously transported downward to maintain the arc under the flux layer and form a welding pool under the arc. Around the arc, the flux melts to form a cavity. The cavity and molten pool advance continuously, and the metal behind the molten pool solidifies to form a continuous weld. This process is carried out under flux, so we can't see it. It can be seen by means of X-ray photography. Because the spiral steel pipe adopts the welding technology of submerged arc automatic welding in addition to this, the production efficiency is high; The auxiliary time of production is less, which saves the time of electrode replacement; The welding conditions are clean saving the cleaning time; High weld quality. It also provides necessary conditions for the delivery of spiral steel pipe factory, so that the production time of large amount of spiral steel pipe can be guaranteed, so it is still widely used.

High manganese content 6 will make the steel brittle and reduce its plasticity. Under what circumstances does the thick wall coil need to be preheated before welding?

Workshop cost.The wall thickness of general coiled pipe is 20mm and the outer diameter is 450-3000mm. It is made of steel plate by direct rolling, welding and forming. The production process of general thick walled coiled pipe can be divided into cold drawing and hot rolling. The production process of cold rolled seamless steel pipe is generally more complex than hot rolling. Roll sizing test shall be carried out for pipe blank first. If there is no response crack on the surface, the round pipe shall be cut by cutting machine, Cut into blanks about meters in length. However, when entering the annealing process, acid shall be used for annealing, it indicates that the quality of steel pipe can not meet the response standard. In appearance, the cold-rolled seamless steel pipe is shorter than the hot-rolled seamless steel pipe, and its wall thickness is generally smaller than that of the hot-rolled seamless steel pipe, but the surface is brighter than that of the thick wall seamless steel pipe. There is not too much roughness on the surface, and there are not too many burrs in the diameter. The thick wall coiled pipe is a powerful manufacturer, quotation, honest operation, genuine and of the same quality. The thick wall coiled pipe is available from stock, with complete specifications,. Docking and strengthening. Coil pipe processing time is short and delivery is fast Low cost. The rolling pipe is mainly used for pipes,Q550b welded steel pipe, billboards, columns, etc.

In short, hot rolled steel pipe is a special thick wall steel pipe rolled with steel plate under heating conditions. Here, the distance between the two welds shall be greater than 100mm, and the distance between the outer wall of the outer branch pipe shall not be less than 50mm.

Work courses.The pipe volume is huge, the production site environment is complex, and the measurement cannot pass through the lower support bench of the steel pipe. This operation is convenient and the measurement accuracy is within & plusmn; Within 10mm, repetition accuracy ≤ 5mm. Thick wall coiled pipe is made of steel plate. Thick wall coiled pipe can be divided into coiled pipe and hot-rolled thick wall coiled pipe.

Outer diameter scale of coiled pipe - mm. Coil pipe is widely used: oil cylinder, hydraulic bridge, roller, etc. The rolling pipe is rolled, welded, formed, de reinforced, flaw detected and delivered under the condition of steel plate heating. Sometimes, the wall with relatively thick thickness needs secondary heating. It is characterized by small outer diameter and uniform wall thickness. First and foremost, the coiled tube will not damage the function of raw materials. The disadvantages of rolling pipe are long processing time and high cost.

Chinese Name: welded pipe English Name: welded tube, welded pipe definition: the pipe formed by crimping the plate and strip into a pipe barrel with specified shape and size, and welding the joint with appropriate welding. Applied discipline: Material Science and Technology (level discipline); Fundamentals of materials science and Technology (level discipline); Material synthesis, preparation and processing (level discipline); Plastic processing technology (level discipline) what are the main raw materials of electric welded steel pipe?

.Circumferential deviation of coiled pipe, pipe groove processing and joint pair: when the pipe wall thickness is less than 6mm, it is type I weld; when the pipe wall thickness is greater than 6mm, it is type V weld; For pipes with diameter greater than 600mm and wall thickness greater than 6mm, the bottom of the pipe shall be sealed at the bottom of the pipe; In addition to the lap joint, the other type of gas coil pipe is continuous and solid V-groove butt welding. If the weld is found to be defective, the weld must be re welded. Rewelding shall not be more than twice. Long term supply of hot rolled steel pipe, large diameter thick wall rolling pipe, thick wall straight seam rolling pipe, steel casing, rolling pipe factory has complete products and excellent quality, The price is favorable. The longitudinal weld of the winding pipe with the same cylindrical part shall not be greater than the spacing between two longitudinal joints shall not be less than 200mm. The arc length of the winding pipe calibration template shall be 1 / 6 ~ I of the circumference of the pipe / the gap between the template and the pipe. Let me introduce the steel plate production standard winding pipe. During the winding process, the surface of the circuit board shall be protected from damage. Parts with severe scars shall be ground to achieve transition, and the wall thickness of the ground part shall not be less than the design wall thickness.

Pipe rolling is to form the steel pipe blank with a steel plate rolling machine, then weld it into steel pipe with submerged arc welding or electric welding and then conduct sizing and forming on other forming equipment. This kind of pipe is single piece production with low efficiency, unstable pipe quality and low dimensional accuracy, but the equipment is simple and the investment is less. Longitudinal welded pipe equipment has high efficiency, good quality, high precision and good performance. It is the main equipment for large-scale production of steel pipes.

In short, hot rolled steel pipe is a special thick wall steel pipe rolled with steel plate under heating conditions. Here