Q345B thick wa
Q345B large diIn short, the use standard of coiled steel pipe is very important, and the above points can be reasonably explained. For the information of our rolled steel pipe, let's simply say so much today. If you need it you can directly consult our manufacturer.
Columns for bearing steel structures such as offshore platforms, and all parts of Shenzhen thick wall coil focus on panel operation. The cutting length of 16Mn thick wall coil adopts photoelectric induction, accurate positioning and automatic cutting. Each working process adopts double pump oil pressure system which runs smoothly, Shenzhen thick wall coiled pipe has good cutting synchronization performance. 16Mn thick wall coiled pipe has different application ranges: length: 0-1400mm, thickness: 2-15mm, diameter: 20-200mm, application voltage: 380V 50Hz. It is used according to the specified parameters and range to ensure that it can play an important role and value in use. The packaging process of new product 16Mn thick wall coil includes main processes such as filling, wrapping and sealing, as well as related pre and post processes, stacking and disassembly. The process of 16Mn thick wall rolling pipe shall be strict, and it shall be produced in the correct way and principle. In addition, the process of 16Mn thick wall coiled pipe also includes measuring or stamping on the package. The use of mechanical packaging products can improve productivity, reduce labor intensity, d7z3xjb87v21w and meet the requirements of cleanliness and hygiene. The production process of rolling pipe is round pipe blank → Heating → Perforation & rarr; Roll cross rolling, continuous rolling or → Off pipe & rarr; Sizing (or reducing) → Cooling → Straightening & rarr; Hydrostatic test (or flaw detection) → Mark & rarr; According to different production, warehousing supply indicators can be divided into hot-rolled pipe, cold-rolled pipe, cold drawn pipe, pipe, etc. quality management? Hot rolled seamless tubes are produced on the automatic tube rolling mill. The solid tube blank is cut into the required length by removing the surface defects. The Shenzhen coiled tube is centered on the end face of the perforated end of the tube blank, and then sent to the heating furnace for heating. It is perforated on the piercing machine. At the same time, it rotates and advances continuously. Under the action of the roll and top head, a cavity called rough tube is gradually formed inside the tube blank, Then it is sent to the automatic pipe mill for continuous rolling, and the wall thickness is adjusted by the whole machine. The Shenzhen coiled pipe is sized by the sizing machine to meet the specification requirements. The production of hot-rolled seamless steel pipe by the continuous pipe mill is relatively advanced. If you want to obtain seamless pipe with smaller size and better quality, 888yixtfrfsbu Shenzhen coil pipe must be cold rolled and cold drawn or a combination of the two. The cold rolling is usually carried out on the roll mill. The steel pipe is rolled in the annular pass composed of variable section circular hole groove and fixed conical plug. The cold drawing is usually carried out on the single chain or double chain cold drawing machine, that is, the heated pipe blank is placed in a closed cylinder, and the perforated rod and rod move, Professional hot-rolled steel pipe, large-diameter thick wall rolling pipe, thick wall straight seam rolling pipe, steel casing, rolling pipe factory has advanced technology, more affordable price and more preferential. Welcome to consult. Make the parts extruded from the smaller die hole. This method can produce the steel pipe with smaller diameter. Work course standard requirements & amp; amp; quot;Standard requirements: the Executive Standards of hot-rolled thick wall coil product line are: GB / t50205-200, GB / t3092-2001, etc.
.The standard FBE epoxy powder shall comply with SY / t0315-1
The main materials are q23q3420, 435cimo and 42cimo, 16 manganese and 16 manganese capacity. Generally, cold rolled sheet can be used for pipe rolling, and the product standards are GB / t50205-200, GB / t3092-2001, etc. Continuous pipe is widely used in petroleum, chemical industry, natural gas transmission, pile driving, urban water supply, heat supply gas supply and other projects.
.The butt joint of coiled pipe (with the same wall thickness) shall not exceed 10% of the wall thickness and not more than 2mm.
With the development of domestic economic situation and the acceleration of welding and casting trend, the advantages of NC cutting are gradually recognized. It has long provided various brand products such as hot-rolled steel pipe, large-diameter thick wall rolling pipe, thick wall straight seam rolling pipe, steel casing and rolling pipe factory. The designated products are complete and the quality is guaranteed. NC cutting not only greatly improves the rate of plate and product quality but also improves the working environment and labor efficiency. At present, the NC cutting machines used in the thick wall coil processing industry are mainly flame and ordinary plasma cutting machines, but pure flame cutting can not meet the needs of modern production. At present, most NC cutting machines are NC plasma cutting machines. This type of cutting machine can meet the needs of thick wall coiled pipe plate processing and thick wall coiled pipe parts processing, so the demand will be greater and greater, but there is still a very obvious gap with foreign countries, which is mainly reflected in: 90% of the developed thick wall coiled pipe processing industry is digital control cutting machine, and only 10% is manual cutting; The CNC cutting machine only accounts for part of the total blanking. 10%, of which the proportion of NC plasma cutting is small. In industrial production, the thermal cutting of thick wall coiled pipe generally includes gas cutting, plasma cutting, laser cutting and so on. Among them, plasma cutting has a wider cutting range than gas cutting More efficient. Fine plasma cutting technology is close to laser cutting in material cutting surface quality, but the cost is much lower than laser cutting. Therefore, since the successful development of the United States in the mid-1950s, plasma cutting has developed rapidly. With the rapid development of computer and digital technology, NC cutting is also developing, which improves the machining accuracy. It shows great advantages in saving materials and improving labor productivity. This leads to the development of plasma cutting technology from manual or semi-automatic to NC, which has become one of the main directions of NC cutting technology. NC plasma cutting technology is a set of high-tech technologies such as NC technology, plasma cutting technology and inverter power supply technology. Its development is based on the common progress of computer, plasma arc characteristic research, power electronics and other disciplines. The CNC cutting technology began in the 1980s and the CNC plasma cutting technology was later. However, recently, some domestic universities, research institutes and manufacturers have studied NC plasma cutting technology and gradually developed and produced various specifications of NC plasma cutting equipment, narrowing the gap of foreign advanced technology.
After pushing, the elbows should be formed in this hot state, because some elbows will be distorted after improper handling, which is not allowed. In addition, after pushing the head, the outer diameter of the front end is usually large and formed by the forming die. The forming die is actually a press. It must have a set of molds, two semi arcs, one on each side. The outer diameter after forming reaches the size of the finished product.
In the process we mentioned, we need to explain each process such as groove. We need to compact both sides of the steel plate with indenter,45# straight seam welded pipe, so as to avoid the formation of peach shaped mouth in the rolling pipe.
The cold deformation process is adopted for the sizing of thick wall rolling pipe end. The commonly used sizing includes punch expanding and punch expanding + sizing ring compression. It has long provided various hot rolled steel pipes, large-diameter thick wall rolling pipe, thick wall straight seam rolling pipe, steel casing, rolling pipe factory, on-site settlement and honest operation for individuals and enterprises all over the country. There are offices in various places, which can cooperate for a long time. When punch expanding, it can reduce the ovality of steel pipes The effect depends on the uniformity of steel pipe wall thickness. For hot-rolled pipes with serious uneven wall thickness such as steel pipe rolled by periodic pipe mill (see pipe rolled by periodic pipe mill), the thick wall coil deteriorates after punch expanding. Therefore, in order to eliminate the influence of uneven wall thickness and reduce the ovality of steel pipe, punch expanding + sizing ring compression method should be adopted.
Continuous pipe is committed to producing all kinds of circumferential seam, longitudinal circumferential continuous pipe and penstock, and is reformed on the basis of the same specification and model of traditional pipe rolling equipment.
target.The diameter of large-diameter thick wall coiled pipe is generally above dn450. Long term supply of hot rolled steel pipe, large diameter thick wall rolling pipe, thick wall straight seam rolling pipe, steel casing, rolling pipe factory, old brand, price advantage and quality guarantee! Sometimes there are two welds for large-diameter thick wall coiled pipe. Why does this happen? It is mainly due to the problems of raw materials and equipment processing. The steel plate with the required width of large-diameter welded pipe required by the customer is not produced by the steel plant, so the two plates must be welded, the delivery can be carried out. The relevant requirements are broader than other products. The detection of large-diameter thick wall coiled pipe is mainly ultrasonic flaw detector, and the longitudinal weld on the same barrel section of the coiled pipe should not be more than two. The group of butt welds of coiled pipe shall be flush. When the nominal diameter is greater than, back sealing welding shall be carried out in the pipe. During pipe rolling processing, the surface damage of the plate shall be prevented.
Material used for steel plate coil: it is required to be explained by the user.
In the process we mentioned, we need to explain each process, so as to avoid the formation of peach shaped mouth in the rolling pipe.
Welding voltage because the welding arc is conical, and the welding voltage directly affects the length of the arc. Therefore, with the increase of welding voltage, the arc length increases, the moving range of arc spots expands,16Mn large diameter welded pipe, the weld pool widens, and a wider weld formation will be obtained. If welding is carried out in a horizontal position, it will only change the width of the weld without affecting the edge transition of the weld. However,20# reel, the external welding of spiral welded pipe is carried out on the slope, and the molten weld metal will flow laterally under the action of gravity. It can be seen that the larger the welding voltage and the wider the weld pool, the more serious the trend of lateral flow of weld metal, * eventually leading to the bias flow of weld metal. Coil products are not only rich in types, but also diversified in processing technology and molding. In most cases, the next process is to expand the diameter of the welded pipe blank to improve the quality of welded pipe shape. In other words, the expanding process has become an important process to ensure the quality of finished pipe in the production of large-diameter straight seam coiled pipe.
Total quality assurance.The detection of thick wall coiled pipe is mainly ultrasonic flaw detector, and the longitudinal weld on the same cylinder section of coiled pipe should not be more than two. Generally, the production process of thick wall coiled pipe can be divided into cold drawing and hot rolling. The production process of cold-rolled seamless steel pipe is generally more complex than hot rolling. Roll sizing test shall be carried out for the pipe blank first. If the surface does not respond to the crack, the round pipe shall be cut by a cutter and cut into a blank with a length of about meters. However, when entering the annealing process, acid shall be used for annealing, and attention shall be paid to whether a large number of bubbles are generated on the surface. If a large number of bubbles are generated, it indicates that the quality of steel pipe can not meet the response standard. In appearance, the cold-rolled seamless steel pipe is shorter than the hot-rolled seamless steel pipe, and its wall thickness is generally smaller than that of the hot-rolled seamless steel pipe, but the surface is brighter than that of the thick wall seamless steel pipe. There is not too much roughness on the surface, and there are not too many burrs in the diameter. The thick wall coiled pipe is a powerful manufacturer, quotation, honest operation, genuine and of the same quality. The thick wall coiled pipe is available from stock with complete specifications,. The group of butt welds of coiled pipe shall be flush. When the nominal diameter is greater than, back sealing welding shall be carried out in the pipe. During pipe rolling processing, the surface damage of the plate shall be prevented. The factory has perfect steel plate coil, thick wall coil, T-shaped welding coil, flaw detection welding coil, 16Mn coil, Q345B coil, special-shaped coil and other production lines. It is a coil factory that can produce large coils of various specifications and wall thicknesses. Our thick wall coil and large coil products are sold to large enterprises all over the country and are deeply trusted and praised by customers. Steel plate coil, thick wall coil, coil, flaw detection welded coil, 16Mn coil and Q345B coil shall be carried out in strict accordance with ISO9001:2000 international quality management standards.
8-100mm steel pipe.
The diameter of thick wall coiled pipe is usually higher than dn450. Thick wall coiled pipe is sometimes two welds. The reason why this happens is mainly due to the problems of raw materials and equipment processing. The steel plate with the required width of welded pipe required by the customer is usually not produced by the steel plant, so two plates need to be welded so the weld will occur.
.The longitudinal weld of the same barrel part of the coiled pipe shall not be greater than 2.
Finish machining is performed below, and after shot peening, the scales on the inner and outer surfaces of the elbow are removed, and both ends are processed with grooves to facilitate welding.
In progress, welcome to consult. Large diameter welded pipe, etc.