Q345B large diameter thick wall welded pipeCorporate merger and reorganization steps

In short, hot rolled steel pipe is a special thick wall steel pipe rolled with steel plate under heating conditions. Here, hot coiling refers to heating to coil the steel plate. Its meaning shall be determined with cold rolled steel pipe.

During pipe rolling, the surface damage of steel plate shall be prevented. The parts with serious scratches must be polished for transition, and the wall thickness of the polished parts shall not be less than the design wall thickness.

.The principle of encoder length measurement is to install the encoder on the oil cylinder and roll the large-diameter pipe. The oil cylinder pushes the welded steel pipe to move on the roller table, the stroke of the oil cylinder can be converted according to the recorded encoder reading and provided by the large-diameter continuous control manufacturer, so as to calculate the length of the steel pipe.

Weld inspection is necessary to detect the weld quality of steel coil pipe. After welding, all the welds are tested by on-line continuous ultrasonic automatic flaw detector to ensure the NDT coverage of the welds. If there are defects, it will automatically alarm and spray marks, and the production will adjust the process parameters at any time to eliminate the defects in time.

.The products are widely used in petroleum, chemical industry, natural gas transportation, heating, gas supply and other projects. The wall thickness of the hot-rolled thick wall coil of retailers generally exceeds 20mm, and the outer diameter range is 450-3000mm. The hot-rolled thick wall coil is rolled, welded, formed, de reinforced, flaw detected and delivered under the state of steel plate heating. Sometimes the wall with special thickness needs secondary heating. It is characterized by small outer diameter tolerance and uniform wall thickness. The main thing is that the hot-rolled thick wall quality management coil will not damage the performance of raw materials. The disadvantages of hot-rolled thick wall coil are long processing time and the diameter of thick wall coil is generally above dn450.

The detection of thick wall coiled pipe is mainly ultrasonic flaw detector, and the longitudinal weld on the same cylinder section of coiled pipe should not be more than two. Generally, the production process of thick wall coiled pipe can be divided into cold drawing and hot rolling. The production process of cold-rolled seamless steel pipe is generally more complex than hot rolling. Roll sizing test shall be carried out for the pipe blank first. If the surface does not respond to the crack, the round pipe shall be cut by a cutter and cut into a blank with a length of about meters. However, when entering the annealing process, acid shall be used for annealing, and attention shall be paid to whether a large number of bubbles are generated on the surface. If a large number of bubbles are generated, it indicates that the quality of steel pipe can not meet the response standard. In appearance, the cold-rolled seamless steel pipe is shorter than the hot-rolled seamless steel pipe, and its wall thickness is generally smaller than that of the hot-rolled seamless steel pipe, but the surface is brighter than that of the thick wall seamless steel pipe. There is not too much roughness on the surface, and there are not too many burrs in the diameter. The thick wall coiled pipe is a powerful manufacturer, quotation, honest operation, genuine and of the same quality. The thick wall coiled pipe is available from stock, with complete specifications,. The group of butt welds of coiled pipe shall be flush. When the nominal diameter is greater than, back sealing welding shall be carried out in the pipe. During pipe rolling processing, the surface damage of the plate shall be prevented. The factory has perfect steel plate coil, thick wall coil, T-shaped welding coil, flaw detection welding coil, 16Mn coil, Q345B coil, special-shaped coil and other production lines. It is a coil factory that can produce large coils of various specifications and wall thicknesses. Our thick wall coil and large coil products are sold to large enterprises all over the country and are deeply trusted and praised by customers. Steel plate coil, thick wall coil, coil, t-welded coil, flaw detection welded coil, 16Mn coil and Q345B coil shall be carried out in strict accordance with ISO9001:2000 international quality management standards.

Welding voltage because the welding arc is conical, and the welding voltage directly affects the length of the arc. Therefore, the production process of thick wall coiled pipe can be divided into cold drawing and hot rolling. The production process of cold rolled seamless steel pipe is generally more complex than hot rolling. Roll sizing test shall be carried out for the pipe blank first. If the surface does not respond to the crack, the round pipe shall be cut by cutting machine to cut the blank with a length of about meters. However, when entering the annealing process, and attention shall be paid to whether a large number of bubbles are generated on the surface. If a large number of bubbles are generated, the cold-rolled seamless steel pipe is shorter than the hot-rolled seamless steel pipe and its wall thickness is generally smaller than that of the hot-rolled seamless steel pipe, but the surface is brighter than that of the thick wall seamless steel pipe. There is not too much roughness on the surface, and there are not too many burrs in the diameter. The thick wall coiled pipe is a powerful manufacturer, quotation, honest operation, genuine and of the same quality. The thick wall coiled pipe is available from stock, with complete specifications,. With the increase of welding voltage the arc length increases, the moving range of arc spots expands, the weld pool widens, and a wider weld formation will be obtained. If welding is carried out in a horizontal position, it will only change the width of the weld without affecting the edge transition of the weld. However, the external welding of spiral welded pipe is carried out on the slope, and the molten weld metal will flow laterally under the action of gravity. We specialize in providing hot-rolled steel pipes, large-diameter thick wall coils, thick wall straight seam coils, steel casings and quality assurance of pipe rolling factory. New and old customers are welcome to consult during the preferential activities. It can be seen that the larger the welding voltage is, the wider the molten pool is, the more serious the trend of lateral flow of weld metal will be * which will eventually lead to the bias flow of weld metal.

Be able to show important value in different industries and fields. When the coiled pipe is greater than 600mm, two longitudinal welds are allowed, and the spacing shall be greater than 200mm.

The materials of steel pipes are 10#, 20#, 35#, large-diameter thick wall rolling pipe, thick wall straight seam rolling pipe, steel casing, rolling pipe factory and other related businesses. Merchants who hope to have this business please. The steel plate with the required width of welded pipe required by customers is generally not produced by the steel factory, so the two plates must be welded, so this kind of weld occurs. The main problem of thick wall coiled pipe is welding. As long as the flaw detection can be carried out the delivery can be carried out. The relevant requirements are broader than other products. The detection of thick wall coiled pipe is mainly ultrasonic flaw detector, and the longitudinal weld on the same cylinder section of coiled pipe should not be more than two. The group of butt welds of coiled pipe shall be flush. When the nominal diameter is greater than, back sealing welding shall be carried out in the pipe. During pipe rolling processing, the surface damage of the plate shall be prevented. High cost. Hot rolled thick wall coiled pipe is widely used: oil cylinder, hydraulic pressure, bridge, roller, etc& amp; amp; quot; Compared with seamless steel pipe, thick wall coil has the disadvantages of low cost, rapid delivery, breaking the fixed specification of seamless steel pipe, etc. Quality department 3 editing of welding process and welded pipe type thick wall coiled pipe is made of steel plate or steel strip after bending and then welding. According to the weld form, it is divided into straight welded pipe and spiral welded pipe. According to the purpose, it is divided into general welded pipe, galvanized welded pipe, oxygen blowing welded pipe wire sleeve, metric welded pipe, idler pipe, deep well pump pipe, transformer pipe, electric welding thin-wall pipe, electric welding special-shaped pipe and spiral welded pipe. Objective knowledge packaging strategy thick wall steel plate coil - thick wall steel plate coil price thick wall coil is formed by bending steel plate or steel strip and the electrical model is

It should be noted that in practice, it is difficult to achieve the ideal proportion of metal sand and metal ball in the rinsing agent, because the hard and brittle metal sand has a higher crushing rate than the metal ball. For this reason, the new rinse agent is added to the cleaning machine, the bending radius is also 1800mm, four bends the material thickness is 4mm, and the bending is 90 & deg;.

The function of parameters of pipe rolling equipment is improved by 30%, which fills the gap that can not be produced by traditional steel rolling equipment. It can produce steel pipes with diameter of more than 400 and wall thickness of 4-100mm. The main materials are q23q3420, 435cimo and 42cimo, 16 manganese and 16 manganese capacity. Generally speaking, cold-rolled sheet can be used for pipe rolling. Product standards: GB / t50205-200, GB / t3092-2001, Q235B coiled pipe, Q345B coiled pipe, large-diameter thin-wall coiled pipe, large-diameter thick wall coiled pipe, stainless steel coiled pipe, L360 coiled pipe, 16Mn coiled pipe and other special products have increased accordingly. With the development of domestic economic situation and the acceleration of welding and casting trend,Q345B straight seam welded pipe,Q345B large diameter thick wall coiled pipe, the advantages of NC cutting have been gradually recognized. NC cutting not only greatly improves the rate of plate and product quality, but also improves the working environment and labor efficiency. At present, the NC cutting machines used in the thick wall coil processing industry are mainly flame and ordinary plasma cutting machines, but pure flame cutting can not meet the needs of modern production. At present, most NC cutting machines are NC plasma cutting machines. This type of cutting machine can meet the needs of thick wall coiled pipe plate processing and thick wall coiled pipe parts processing, so the demand will be greater and greater, but there is still a very obvious gap with foreign countries, which is mainly reflected in: 90% of the developed thick wall coiled pipe processing industry is digital control cutting machine, and only 10% is manual cutting; The CNC cutting machine only accounts for part of the total blanking. 10%, of which the proportion of NC plasma cutting is small. In industrial production, the thermal cutting of thick wall coiled pipe generally includes gas cutting, plasma cutting, laser cutting and so on. Among them, plasma cutting has a wider cutting range than gas cutting More efficient. Fine plasma cutting technology is close to laser cutting in material cutting surface quality, but the cost is much lower than laser cutting. Therefore, since the successful development of the United States in the mid-1950s, plasma cutting has developed rapidly. With the rapid development of computer and digital technology NC cutting is also developing, which has become one of the main directions of NC cutting technology. NC plasma cutting technology is a set of high-tech technologies such as NC technology which improves the machining accuracy. It shows great advantages in saving materials and improving labor productivity. This leads to the development of plasma cutting technology from manual or semi-automatic to NC, plasma cutting technology and inverter power supply technology. Its development is based on the common progress of computer, plasma arc characteristic research, power electronics and other disciplines. The CNC cutting technology began in the 1980s, and the CNC plasma cutting technology was later. However, recently, some domestic universities, research institutes and manufacturers have studied NC plasma cutting technology and gradually developed and produced various specifications of NC plasma cutting equipment, narrowing the gap of foreign advanced technology. 20 old brands, price

Since the groove sizes of longitudinal and circumferential joints of hot-rolled pipes are different, it is necessary to confirm whether the inner side is upward before plate rolling to ensure the correctness of groove direction.

Create brilliance.Move the steel pipe twice to weld and reinforce the rolled pipe joint, and then transport it to the welding platform for welding.

The cold deformation process is adopted for the sizing of thick wall rolling pipe end. The commonly used sizing includes punch expanding and punch expanding + sizing ring compression. It has long provided various hot rolled steel pipes, large-diameter thick wall rolling pipe, thick wall straight seam rolling pipe, steel casing, rolling pipe factory, on-site settlement and honest operation for individuals and enterprises all over the country. There are offices in various places, which can cooperate for a long time. When punch expanding, it can reduce the ovality of steel pipes The effect depends on the uniformity of steel pipe wall thickness. For hot-rolled pipes with serious uneven wall thickness, such as steel pipe rolled by periodic pipe mill (see pipe rolled by periodic pipe mill), the thick wall coil deteriorates after punch expanding. Therefore, in order to eliminate the influence of uneven wall thickness and reduce the ovality of steel pipe, punch expanding + sizing ring compression method should be adopted.

The detection of thick wall coiled pipe is mainly ultrasonic flaw detector, and the longitudinal weld on the same cylinder section of coiled pipe should not be more than two. Generally, the production process of thick wall coiled pipe can be divided into cold drawing and hot rolling. The production process of cold-rolled seamless steel pipe is generally more complex than hot rolling. Roll sizing test shall be carried out for the pipe blank first. If the surface does not respond to the crack, the round pipe shall be cut by a cutter and cut into a blank with a length of about meters. However, and attention shall be paid to whether a large number of bubbles are generated on the surface. If a large number of bubbles are generated, it indicates that the quality of steel pipe can not meet the response standard. In appearance, the cold-rolled seamless steel pipe is shorter than the hot-rolled seamless steel pipe, and its wall thickness is generally smaller than that of the hot-rolled seamless steel pipe, but the surface is brighter than that of the thick wall seamless steel pipe. There is not too much roughness on the surface, and there are not too many burrs in the diameter. The thick wall coiled pipe is a powerful manufacturer, quotation, honest operation, genuine and of the same quality. The thick wall coiled pipe is available from stock, with complete specifications,. The group of butt welds of coiled pipe shall be flush. When the nominal diameter is greater than, back sealing welding shall be carried out in the pipe. During pipe rolling processing, the surface damage of the plate shall be prevented. The factory has perfect steel plate coil, thick wall coil, T-shaped welding coil, flaw detection welding coil, 16Mn coil, Q345B coil, special-shaped coil and other production lines. It is a coil factory that can produce large coils of various specifications and wall thicknesses. Our thick wall coil and large coil products are sold to large enterprises all over the country and are deeply trusted and praised by customers. Steel plate coil,Q460b large diameter reel, thick wall coil, coil, t-welded coil, flaw detection welded coil 16Mn coil and Q345B coil shall be carried out in strict accordance with ISO9001:2000 international quality management standards.

.It is to preheat rather than increase the line energy. Reel needs quality, honest business! Let's talk about our productivity.

Generally, the wall thickness of the coiled pipe is 20mm and the outer diameter is 450-3000mm. It is directly welded formed, rolled, butted, removed and reinforced from the steel plate. The coil pipe has the advantages of short processing time, fast delivery and low cost. The rolling pipe is mainly used for pipes, billboards, etc.

Gas and other projects.