The products are widely used in petroleum, chemical industry, natural gas transportation, pile driving and urban water supply, heating, gas supply and other projects. The wall thickness of the hot-rolled thick wall coil of retailers generally exceeds 20mm, and the outer diameter range is 450-3000mm. The hot-rolled thick wall coil is rolled, welded, formed, de reinforced, flaw detected and delivered under the state of steel plate heating. Sometimes the wall with special thickness needs secondary heating. It is characterized by small outer diameter tolerance and uniform wall thickness. The main thing is that the hot-rolled thick wall quality management coil will not damage the performance of raw materials. The disadvantages of hot-rolled thick wall coil are long processing time and the diameter of thick wall coil is generally above dn450.
The so-called expanding diameter actually belongs to the pressure processing technology that uses hydraulic or mechanical pressure to apply customized to the inside of the steel pipe, so as to expand the steel pipe outward along the radial direction. Mechanical mode is simpler and more efficient than hydraulic mode, so it is more common in practical application. In particular, it is adopted in the very advanced expanding process of several large-diameter straight seam rolling pipelines.
.Before forming, the strip steel is leveled, trimmed, planed, surface cleaned, transported and pre bent.
The convex hull on the surface of the crimp roll shall be treated. Before repeated processing, the equipment surface shall be treated to prevent the convex hull steel plate with abnormal roll surface from causing pits.
.Let me introduce the standard coil produced by steel plate. In the process of rolling, the surface of the circuit board should be protected from damage. Parts with severe scars shall be ground to achieve transition, and the wall thickness of the ground part shall not be less than the design wall thickness.
Circumferential deviation of coiled pipe, pipe groove processing and joint pair: when the pipe wall thickness is less than 6mm it is type I weld; when the pipe wall thickness is greater than 6mm, it is type V weld; For pipes with diameter greater than 600mm and wall thickness greater than 6mm, the bottom of the pipe shall be sealed at the bottom of the pipe; In addition to the lap joint, the other type of gas coil pipe is continuous and solid V-groove butt welding. If the weld is found to be defective, the weld must be re welded. Rewelding shall not be more than twice. Long term supply of hot rolled steel pipe, large diameter thick wall rolling pipe, thick wall straight seam rolling pipe, steel casing, rolling pipe factory has complete products and excellent quality The price is favorable. The longitudinal weld of the winding pipe with the same cylindrical part shall not be greater than the spacing between two longitudinal joints shall not be less than 200mm. The arc length of the winding pipe calibration template shall be 1 / 6 ~ I of the circumference of the pipe / the gap between the template and the pipe. Let me introduce the steel plate production standard winding pipe. During the winding process, the surface of the circuit board shall be protected from damage. Parts with severe scars shall be ground to achieve transition, and the wall thickness of the ground part shall not be less than the design wall thickness.
Steel casing means that in the process of manual hole digging pile, due to the unstable soil, it is difficult to construct reinforced concrete retaining wall, so steel retaining wall is used to protect the hole pile to prevent hole collapse and affect the construction progress and safety. High price hot rolled steel pipe of various specifications, thick wall straight seam rolling pipe, steel casing, rolling pipe factory has timely supply and high cost performance. It has become the preferred brand for many wire products. Welcome to buy! The steel pile casing is a circular barrel hooped with iron sheet according to the size of the hole pile, and both ends are empty barrels. It can stabilize the hole wall, prevent hole collapse, isolate the surface water, guide the drill bit, fix the pile position, etc., which is generally 20-40cm larger than the pile diameter. The buried depth depends on the properties of the soil. The deviation of the plane position shall not be greater than 5cm, and the inclination shall be less than 1%. The reel is committed to the production of circumferential joints All kinds of longitudinal coils and steel penstocks are reformed on the basis of similar specifications and models of traditional coil equipment. The function of improving the parameters of the pipe rolling equipment by 30% fills the gap that the original traditional rolling equipment can not produce. It can produce steel pipes with diameter of more than 400 and wall thickness of 8-100mm. The materials mainly include Q235 Q345, 45 # 35cimo and 42cimo, 16 manganese and 16 manganese capacity. Generally, cold-rolled plate can be used for rolling pipe, etc. Product executive standard: GB / t50205-200, GB / t3092-2001, etc. Coiled pipes are widely used in petroleum, chemical industry, natural gas transportation, pile driving, urban water supply, heat supply, gas supply and other projects.
The main purpose of preheating is to reduce the cooling rate of welded joints and preheat temperature. As can be seen from the table preheating can reduce the cooling rate, but basically does not affect the time spent at high temperature, which is ideal. Therefore, when welding thick wall coils with hardening trend, the main technical measure to reduce the cooling rate and hardening trend is preheating rather than increasing the line energy. Plasma cutting of thick wall coiled pipe is more effective than gas cutting
The cold deformation process is adopted for the sizing of thick wall rolling pipe end. The commonly used sizing includes punch expanding and punch expanding + sizing ring compression. It has long provided various hot rolled steel pipes, large-diameter thick wall rolling pipe, thick wall straight seam rolling pipe, steel casing, rolling pipe factory, on-site settlement and honest operation for individuals and enterprises all over the country. There are offices in various places, which can cooperate for a long time. When punch expanding, it can reduce the ovality of steel pipes The effect depends on the uniformity of steel pipe wall thickness. For hot-rolled pipes with serious uneven wall thickness, such as steel pipe rolled by periodic pipe mill (see pipe rolled by periodic pipe mill) the thick wall coil deteriorates after punch expanding. Therefore, in order to eliminate the influence of uneven wall thickness and reduce the ovality of steel pipe, punch expanding + sizing ring compression method should be adopted.
The effect of antirust oil on thick wall coiled pipe is antirust effect, which can make the thick wall coiled pipe as smooth as new for a long time and reduce the external corrosion to it. It can also increase its sealing performance and ensure that there will be no problems when transporting fluid. In addition, uses antirust oil to isolate the direct air of thick wall welded pipe, so it has little chance of being changed by the external situation, which increases its stable performance and safer use.
Honesty is the foundation.The distance between the two longitudinal slits of the reel group shall be greater than 100mm. The outer wall of the branch pipe shall be longitudinal, and the circumferential weld shall not be less than 50mm.
Service specification of coiled steel pipe: there are spiral welded pipe and seamless pipe, and the pressure resistance of gas and water is different.
The weld reinforcement is increased, the weld formation is deteriorated and the edge transition is poor.
Deviation reel as follows (unit: mm): nominal diameter & amp; amp; lt; 800 800 to 1200 1300 to 1600 1700 to 2400 2600 to 3000 perimeter Deviation & plusmn; 5± 7± 9± 11± The ovality is 1% of the outer diameter, and the quality of no more than 4 steel plate coils is greatly affected by the weld size, mainly including the comprehensive factors such as welding process parameters, welding wire shape and position parameters, flux process performance and formed joint.
Installation requirements., low cost. The rolling pipe is mainly used for pipes, billboards, columns, etc.
For pipe fittings with nominal pressure indicating their grade or specified pressure and temperature rating, the pressure and temperature rating specified in the standard shall be used as the reference. For example, for pipe fittings with nominal thickness of straight pipe connected to them, the applicable pressure and temperature rating shall be determined according to the reference pipe grade specified in the standard, For example, for pipe fittings with only overall dimensions specified in gb14383 ~ GB standards, such as GB1245 and GB 1340, confirmatory test shall be conducted to determine their bearing strength.
The pipeline installation sequence shall be adopted according to the principle of zoning and subsystem. First the lower level, then the upper level, and then the difficulty. In principle, the pipes connected to the machine are arranged from inside to outside to reduce the impact of welding stress on the installation accuracy of the machine. The joints of indoor and outdoor pipes shall be left outdoors. Q345B thick wall continuous pipe is a widely used carbon steel material. Q345B thick wall continuous pipe with thickness greater than 10mm is widely used in drainage engineering, sewage pipeline dredging pipeline, construction pipeline, etc. Q345B thick wall continuous pipe is a welded steel pipe product with relatively simple and flexible process. This kind of steel pipe is usually not in stock and is customized. If the quantity is small, the raw materials are not good. The main problem of Q345B thick wall continuous pipe is welding. As long as possible, delivery related requirements can be compared with other products.
.The steel plate or strip is bent and then welded to form a thick wall coil. According to the welding form, it is divided into straight seam welded pipe and spiral welded pipe. It is divided into ordinary welded pipe, galvanized welded pipe, oxygen blowing welded pipe, wire sleeve, metric welded pipe, rolling pipe, deep well pump pipe, automobile pipe, transformer pipe, welded thin-wall pipe, welded pipe and spiral welded pipe. Coil pipe is dedicated to the production of, longitudinal ring coil pipe and steel pressure pipe, and is modified according to similar specifications of traditional rolling equipment. The function of increasing the parameters of spiral steel pipe equipment by 30% fills the gap that the original traditional rolling equipment can not produce. It can produce steel pipes with a diameter of 400 or more and a wall thickness of 8-100mm. The material mainly includes q23 q34 20#, 16 manganese, 16 manganese capacity etc. Product executive standards include: GB / t50205-2001, GB / t3092-2001, chemicals, natural gas transportation, pile driving, heating, gas supply and other projects.
Compared with seamless steel pipe, rapid delivery, breaking the fixed specification of seamless steel pipe, etc. Thick wall coiled pipe is made of steel plate or steel strip by bending and then welding. According to the weld form, it is divided into straight welded pipe and spiral welded pipe. According to the purpose, it is divided into general welded pipe, galvanized welded pipe, oxygen blowing welded pipe, wire sleeve, metric welded pipe, idler pipe, deep well pump pipe, automobile pipe, transformer pipe, electric welding thin-wall pipe, electric welding special-shaped pipe and spiral welded pipe. Rolling pipe is committed to producing all kinds of rolling pipes and steel penstocks with circumferential seam and longitudinal ring, and is reformed on the basis of similar specifications and models of traditional rolling equipment. The function of improving the parameters of the rolling and welding steel pipe equipment by 30% fills the gap that the original traditional rolling equipment can not produce. It can produce steel pipes with diameter of more than 400 and wall thickness of 8-100mm. Materials mainly include q23 q34 20#, 16 manganese, 16 manganese capacity, etc. Product executive standard: GB / t50205-200, etc. The products are widely used in petroleum, chemical industry, natural gas transportation, pile driving and urban water supply, heating, gas supply and other projects.
In progress, welcome to consult. Large diameter welded pipe, etc.