steel products.
The influence of welding process parameters on welding current mainly includes two aspects: according to the production characteristics of spiral steel pipe, small welding current is usually used for internal welding
.8-100mm steel pipe.
Gas and other projects.
.First, select the specification and put forward the pipe, such as 90 & deg; Elbow, which can calculate the curvature to calculate the 90 DEG of the long material; Elbow, and then cut with the length as the fixed length.
The effect of antirust oil on thick wall coiled pipe is antirust effect, which can make the thick wall coiled pipe as smooth as new for a long time and reduce the external corrosion to it. It can also increase its sealing performance and ensure that there will be no problems when transporting fluid. In addition, it has moisture-proof performance, uses antirust oil to isolate the direct air of thick wall welded pipe so it has little chance of being changed by the external situation, which increases its stable performance and safer use.
Welding voltage because the welding arc is conical and the welding voltage directly affects the length of the arc. Therefore, the general production process of thick wall continuous pipe can be divided into cold drawing and hot rolling. The production process of cold rolled seamless steel pipe is generally more complex than that of hot rolled steel pipe. First, the pipe must be subject to winding diameter test. If there is no response crack on the surface, the round pipe will be cut and the growth of the blank is about M. However, during annealing, acid should be used for annealing, and attention should be paid to whether there are a large number of bubbles on the surface. If a large number of bubbles appear, the quality of the steel pipe will not meet the response standard. The appearance of cold-rolled seamless steel pipe is shorter than that of hot-rolled seamless steel pipe, and the wall thickness is generally smaller than that of hot-rolled seamless steel pipe but the surface is brighter than that of thick wall seamless steel pipe, the surface is not too rough, the diameter is not too prickly, and the strength is high. The manufacturer offers, operates in good faith, and has a real price. The same specification, thick wall continuous pipe, spot supply, and complete specifications,. With the increase of welding voltage, the arc length increases, the moving range of solder joint increases and the molten pool widens. If welding is carried out in a horizontal position the weld width will be changed, but the edge transition of the weld will not be affected. However, the external welding of spiral welded pipe is carried out on the slope, and the molten weld metal will flow laterally under the action of gravity. We specialize in providing hot-rolled steel pipe, large-diameter thick wall continuous pipe, thick wall straight seam continuous pipe, steel casing and quality assurance of pipe rolling plant. During the preferential activities, new and old customers are welcome to consult. Therefore, the greater the welding voltage, the wider the weld pool, the more serious the transverse flow of weld metal, and finally lead to the bias of weld metal.
Electric fusion connection: when the pipe fittings leave the factory, the resistance wire is buried in the pipe fittings to make electric fusion pipe fittings. At the construction site, only the plug of the special welding instrument and the socket of the pipe fittings need to be connected. The inner body of the pipe fittings melts the outer plastic of the pipe fittings and the inner plastic of the pipe fittings to form a reliable connection, and combines the timing methods such as special digital timekeeper and installation indicator hole.
The utility model is characterized in that a T-shaped welded steel pipe needs to be hung when measuring the length. In addition, the photoelectric switch detection also has a certain error, which may require a comprehensive measurement of the circumferential weld butt steel pipe.
The distance between the two longitudinal slits of the reel assembly shall be greater than 100mm. The distance between the outer wall of the branch pipe and the weld shall not be less than 50mm.
Finance Department.: 90% of the developed thick wall coil processing industry is CNC cutting machine, of which the proportion of NC plasma cutting is small. In industrial production, the thermal cutting of thick wall coiled pipe generally includes gas cutting, plasma cutting, laser cutting and so on. Among them, plasma cutting has a wider cutting range than gas cutting More efficient. Fine plasma cutting technology is close to laser cutting in material cutting surface quality, but the cost is much lower than laser cutting. Therefore, since the successful development of the United States in the mid-1950s, plasma cutting has developed rapidly. Professional hot-rolled steel pipe, large-diameter thick wall rolling pipe thick wall straight seam rolling pipe, steel casing, rolling pipe factory, high pressure rating, good waterproof performance, fire and high temperature resistance, strong overload capacity, corrosion resistance, radiation protection and long service life. With the rapid development of computer and digital technology, NC cutting has also expanded and improved the processing accuracy. It shows great advantages in saving materials and improving labor productivity. This leads to the development of plasma cutting technology from manual or semi-automatic to NC, which has become one of the main directions of NC cutting technology. NC plasma cutting technology is a set of high-tech technologies such as NC technology, plasma cutting technology and inverter power supply technology. Its development is based on the common progress of computer, plasma arc characteristic research, power electronics and other disciplines. The CNC cutting technology began in the 1980s, and the CNC plasma cutting technology was later. However, recently, some domestic universities, research institutes and manufacturers have studied NC plasma cutting technology and gradually developed and produced various specifications of NC plasma cutting equipment, narrowing the gap of foreign advanced technology. The large-scale rolling pipe factory of rolling pipe, t-welded rolling pipe, 16Mn rolling pipe, Q345B rolling pipe and special-shaped rolling pipe, and the t-welded rolling pipe, 16Mn rolling pipe, Q345B rolling pipe and special-shaped rolling pipe produced by the rolling pipe factory are exported to major engineering buildings at home and abroad.
The rolling pipe production technology requires that the rolling pipe weld is a double-sided weld, two longitudinal welds are allowed, and the weld spacing exceeds 300 mm. The welding appearance and quality standard shall not be lower than the level standard in the welding specification.
Generally, the wall thickness of the coiled pipe is 20mm and the outer diameter is 450-3000mm. It is directly welded, formed, rolled, butted, removed and reinforced from the steel plate. The coil pipe has the advantages of short processing time, fast delivery and low cost. The rolling pipe is mainly used for pipes, billboards, etc.
After pushing, the elbows should be formed in this hot state, because some elbows will be distorted after improper handling, which is not allowed. In addition, after pushing the head, the outer diameter of the front end is usually large and formed by the forming die. The forming die is actually a press. It must have a set of molds two semi arcs, one on each side. The outer diameter after forming reaches the size of the finished product.
Range.Thick wall coiled pipe is usually higher than dn450. Thick wall coiled pipe is sometimes two welds. Why does this happen mainly because of raw material problems and equipment processing problems? The steel plate with the required width of welded pipe required by the customer is usually not produced by the steel plant, so two plates need to be welded, the requirements related to delivery are wider than other products. The detection of thick wall coiled pipe is mainly ultrasonic flaw detector. The longitudinal weld on the same cylindrical part of the coiled pipe shall not be greater than 2. When the coil pipe is butt welded, the corresponding parts shall be flushed to. When the nominal diameter is larger than the inner seal, boiling water pipes, water wall pipes and superheated steam pipes, large smoke pipes and small smoke pipe carbon structural steel hot-rolled or cold-rolled (drawn) seamless steel pipes for locomotive boilers. No. 20 and 45 steel are mainly used for steel plate rolling. In addition to ensuring chemical composition and mechanical properties hydrostatic test shall be carried out. Crimping and flared rolling shall be delivered in hot rolling state, and cold rolling (pulling) shall be delivered in heat treatment state.
The rolling pipe factory mainly produces steel plate rolling pipe and thick wall rolling pipe. With the development of domestic economic situation and the acceleration of welding and casting trend, the advantage of NC cutting is gradually recognized. NC cutting not only greatly improves the rate of plate and product quality, but also improves the working environment and labor efficiency. At present, the CNC cutting machines used in the thick wall rolling pipe processing industry are mainly flame and ordinary plasma cutting machines, but pure flame cutting can not meet the needs of modern production, At present, most CNC cutting machines are CNC plasma cutting machines. This type of cutting machine can meet the needs of thick wall coiled pipe plate processing and thick wall coiled pipe parts processing, so the demand will be greater and greater, but there is still a very obvious gap with foreign countries, mainly in
.The process of heating the whole thick wall coil or welding area before welding is called preheating. For the steel with high welding strength grade, it has hardening trend, material, weldment and large thickness. When the ambient temperature around the welding area is too low, it is necessary to preheat the weldment before welding.
The wall thickness of coiled pipe like coiled pipe is under 20mm and the outer diameter is 450-3000mm. It is made of steel plate by direct rolling, welding, forming, butt joint and rebar removal. Coil pipe has the characteristics of short processing time, rapid delivery and low cost. The rolling pipe is mainly used for pipes, billboards, columns, etc.
The main problem of thick wall coiled pipe is welding. As long as flaw detection can be carried out