West-EndNational standard galvanized pipeState at the time of delivery

There are many forms of heating furnace, but the ring heating furnace is mainly used. The heating furnace has an annular furnace bottom, which can rotate slowly, the blank is loaded along the diameter direction of the furnace bottom from the inlet, and can be heated and homogenized to the specified temperature when it is used at the outlet. The production process of seamless square tube is relatively slow, and the heating operation especially needs patience. Because if the heating operation is not standardized, cracks, folding and eccentricity on the inner or outer surface of the tube blank will only produce waste products and defective products.

The general delivery length of q355b square pipe is 4000mm-12000mm, mostly 6000mm and 12000mm. Q355b square tube is allowed to deliver short and non fixed length products not less than 2000mm, or in the form of interface tube, but the Demander shall cut off the interface tube when using it. The weight of short length and non fixed length products shall not exceed 5% of the total delivery. For q355b square tube with theoretical weight greater than 20kgm, and the total bending degree shall not be greater than 0.2% of the total length. The square tube is classified according to the production process: hot rolled seamless square tube, cold drawn seamless square tube, seamless square tube and square tube.

West-End.C. electric furnace steel: (a) electric arc furnace steel; (b) Electroslag furnace steel; (c) Induction furnace steel; (d) Vacuum consumable furnace steel; (e) Electron beam furnace steel.

The strength of square tube refers to the function that the data of square tube are destroyed under static load (appropriate plastic deformation or fracture). Because the action forms of load include tension, contraction, meandering, shear and so on, compressive strength flexural strength, shear strength and so on. There is often a definite connection between various strengths. In normal use, tensile strength is often used as the fundamental strength gauge.

.The standard quantity of combustible and nonflammable square pipes is gbt97-1 (gbt97-199). The representative material is l245-l4 pipeline steel. Professional square pipes, square rectangular pipes,West-EndDN25 galvanized welded pipe, seamless square pipes, galvanized square pipes and galvanized pipes are of high quality and low price. They are fire-resistant, waterproof, high temperature resistant, durable, safe and reliable. They are mainly used to transport combustible and nonflammable fluids with high requirements.

Soft blowing treatment of molten steel after calcium treatment can reduce residual inclusions in molten steel and better wrap MNS around al20 CAS and other cores.

The disadvantage of solid bending is that it has tensile thinning effect. The actual bending will produce tension at the bending point, q355b square tube, q355b square tube, Q345B square tube, Q345B square tube and hot-rolled right angle square tube are of good quality and excellent quality. We have become a supplier of many enterprises. Q355b square tube and I-beam are two products with different shapes. Under the condition of the same material, but their uses are very different. The shape is different. Q355b square tube is a cuboid, and I-beam is in I-shape. The purpose is different. I-beam can be used as span and support. Square pipe is a little worse than span. It is no problem to do support. However, the specific selection of steel depends on the requirements of the project. Square tube practical application square tube for structure (gbt8162-199) is a square tube for general structure and mechanical structure.

Compared with other traditional pipes, square pipe supply steel pipe has lighter raw materials high strength, good resistance, can withstand high internal pressure, sensitive application, and can get used to messy or bad geological conditions.

Job description.Now, with the continuous development of q355b square tube, its use is becoming more and more extensive, and the technology is also following up. Therefore, we still look forward to the development of q355b square tube in the future.

The great difference between the square pipe and the thin-walled steel pipe produced by the square pipe factory lies in the thickness of the steel pipe wall. Generally speaking the thin-walled steel pipe is cold drawn technology, while the square pipe generally uses hot rolling technology. If it is distinguished by the unit of measurement, it is generally believed that the watershed between the square pipe and the thin-walled steel pipe is that the wall thickness diameter is equal to 0.02, and the thin-walled steel pipe is that the wall thickness diameter is less than 0.02, Larger than is the square pipe. In terms of use, thin-walled steel pipes are mostly used in pipes. The square tube is mostly used in the blank of hollow parts. Used on pressure bearing and important pipelines.

The welding sequence is to reduce deformation. The welding sequence of rectangular butt welding shall adopt layered and symmetrical skip welding from the middle to both sides according to the following principles. The welding deformation is smaller than that of straight through welding, which is conducive to the dispersion and release of stress and avoid complex stress in weldments. During straight through welding, the narrow plastic deformation zone formed at the beginning of welding only occurs once. Moreover, the heat input is large, the heating area is large, and the plastic deformation area caused by compression is large, so the shrinkage deformation after welding is very large. In case of layered and segmented skip welding, the section of each layer is very small, and the heat required is small, and each layer is divided into several sections for skip welding. Each welding section basically re establishes the secondary temperature field on the cold steel plate, and a narrow plastic deformation zone appears each time. Therefore, the average width of the plastic deformation zone (i.e. the size of transverse shrinkage) is smaller than that of the corresponding layered straight through welding and the longitudinal shrinkage is also smaller, The welding deformation is smaller than that of continuous filling.

It must be noted that in the overall process of square tube coating process, the cost of surface treatment is still relatively high, so it is very important to select appropriate treatment. Only by selecting the right treatment can the coating quality of square pipe be well guaranteed.

market price.At the same time, the heating temperature and heating time will also have a great impact on the performance of square tube. The heating of square tube blank is the key process to ensure that the square tube blank has enough plasticity and complete the smooth perforation. If the heating temperature is too high or the heating time is too long, the billet of the square tube will be burned and decarburized, and even the chemical composition of the square tube will be unqualified (unqualified carbon content), which is easy to cause batch quality problems and seriously affect the product qualification rate.

Hot dip galvanized square tube is a kind of square tube which is welded after using steel plate or steel strip to curl and form, and on the basis of this square tube, the square tube is placed in the hot dip galvanized pool and formed through a series of chemical reactions; The production process of hot-dip galvanized square pipe is relatively simple, but the production efficiency is very high and there are many specifications and varieties, but this kind of square pipe needs little equipment and capital, which is more suitable for the production of small galvanized square pipe manufacturers.

The strength, plasticity and angle discussed later are the machine function indicators of metal under static load. In practice, many mechanical machines are under repeated load, and the whole opportunity is tired in this environment.

West-End.Great relationship. Large fillet radius, insufficient blank holder area, easy to produce unstable wrinkles; If the fillet is too small, the resistance of the material into the die will increase in the deformation process, and the material is not easy to move and transfer inward, thus increasing the large tensile stress in the force transfer area, which may lead to tensile cracking.

The surface compressive stress characteristics of the square tube will be obtained after isothermal quenching.

The welding sequence is to reduce deformation. The welding sequence of rectangular butt welding shall adopt layered and symmetrical skip welding from the middle to both sides according to the following principles. The welding deformation is smaller than that of straight through welding, which is conducive to the dispersion and release of stress and avoid complex stress in weldments. During straight through welding, the narrow plastic deformation zone formed at the beginning of welding only occurs once. Moreover, due to continuous welding, the heat input is large, the heating area is large, and the plastic deformation area caused by compression is large, so the shrinkage deformation after welding is very large. In case of layered and segmented skip welding, the section of each layer is very small, and the heat required is small, and each layer is divided into several sections for skip welding. Each welding section basically re establishes the secondary temperature field on the cold steel plate,West-EndHow much is 30 galvanized square tube, and a narrow plastic deformation zone appears each time. Therefore, the average width of the plastic deformation zone (i.e. the size of transverse shrinkage) is smaller than that of the corresponding layered straight through welding and the longitudinal shrinkage is also smaller