ShawiniganSquare pipe galvanized pipeApplication development in the market

High productivity of square tube: the efficiency of cold production of mechanical parts is very high, especially for parts with large batch. Cold production can be several times, several times or even hundreds of times higher than cutting. For example, the use of cold pin for automobile is twice higher than that of cutting. At present, cold pin automata is used to improve productivity. The productivity of table cooling automata is equivalent to that of 100 ordinary lathes or 10 shaft self-propelled machines.

Square tube saves raw materials: the material rate of cold parts can usually reach more than 80%. For example,ShawiniganHow much is square tube galvanizing, while the material rate when cold is used is increased to 92%; For another example, after the universal joint bearing sleeve is changed to cold the material rate is increased from 28% in the past to%. It can be seen that the use of cold production of mechanical parts can save a lot of steel and non-ferrous metal materials.

Shawinigan.Empty bending empty bending is the bending moment formed in one direction between the outer roll and the outer wall of the tube blank to bend the strip. Empty bending will compress the bending line, the compression effect will lengthen the bending line longitudinally, and the metal at the bending will accumulate and thicken, which is the compression thickening effect of empty bending.

Square tube flattening test is a kind of test to check the deformation performance of metal tubes (seamless square tubes and rectangular tubes) flattened to the specified size and show their defects. Relevant flattening tests shall be carried out in accordance with relevant provisions of test standards. Requirements for samples samples can be taken from metal pipes with qualified appearance. Generally, sawing is adopted. The inner and outer walls of the pipe shall retain the original surface without any processing. Sample length L & asymp; D (D is the outer diameter of the pipe). When the outer diameter is large, the length l shall not exceed 100mm. When the outer diameter is less than 20mm, l = 20mm. When cutting the sample, the surface of the sample shall not be damaged and the performance of the metal shall not be changed due to heating or cold processing. The edge of the section shall be flattened. The flattening test is a test to check the deformation performance of the metal pipe (seamless square pipe and rectangular pipe) flattened to the specified size and show its defects. Relevant flattening tests shall be carried out in accordance with relevant provisions of test standards.

.Electrochemical polishing: long specular gloss, stable process, less pollution and good durability. Suitable for mass production, it is mainly applied to high-grade products, the hardness method is commonly used to measure the hardness in production. It uses the indenter with fixed geometry to measure the hardness value of the metal material surface tested under fixed load according to the degree of hardness.

Production standard classification square tube is divided according to production standard: national standard square tube, Japanese standard square tube, British standard square tube, American standard square tube European standard square tube and non-standard square tube.

Normalized: A. pearlite steel; b. Bainitic steel; c. Martensitic steel; d. Austenitic steel.

There are some defects in q355b square tube during stretching, which are caused by the following reasons. The common main reasons are as follows: select the appropriate q355b square tube material, 1Cr18Ni9Ti is more stable than 0Cr18Ni9Ti and has better crack resistance. Therefore 1Cr18Ni9Ti material should be selected as much as possible.

Respect for customers.Tensile strength: 490-675 yield strength: & Ge; 345 elongation: & Ge; 22 mechanical properties of seamless pipe: tensile strength: 490-675 yield strength: ≥ 345 elongation: & Ge; 21 mechanical properties of seamless pipe: tensile strength: 490-675 yield strength: ≥ 345 elongation: & Ge; 21 mechanical properties of seamless pipe: tensile strength: 490-675 yield strength: ≥ 345 elongation: & Ge; 22 mechanical properties of seamless pipe: tensile strength: 490-675 yield strength: ≥ 345 elongation: & Ge; 22 square tube belongs to low alloy series. It is one of the materials of seamless steel pipe. In low alloy materials, this material is ordinary. Square tube used to be called Q345B square tube.

Formulate the documents stored by the square tube for a long time and implement them in accordance with.

The strength, plasticity and angle discussed later are the machine function indicators of metal under static load. In practice, many mechanical machines are under repeated load, and the whole opportunity is tired in this environment.

The great difference between the square pipe and the thin-walled steel pipe produced by the square pipe factory lies in the thickness of the steel pipe wall. Generally speaking, while the square pipe generally uses hot rolling technology. If it is distinguished by the unit of measurement, it is generally believed that the watershed between the square pipe and the thin-walled steel pipe is that the wall thickness diameter is equal to 0.02, and the thin-walled steel pipe is that the wall thickness diameter is less than 0.02, Larger than is the square pipe. In terms of use, thin-walled steel pipes are mostly used in pipes. The square tube is mostly used in the blank of hollow parts. Used on pressure bearing and important pipelines.

Quality improvement.The square tube adopts the electric contact pressure gauge to press down the pressure of the oil cylinder on both sides of the conveyor to ensure the smooth transportation of the strip steel.

In the square tube production process of welding before forming the forming is mainly completed by the sizing frame. The sizing machine is generally a two high mill, including horizontal frame and vertical roll frame. At present, there are mainly two kinds of square pipe pass design: one is the horizontal frame is designed according to the box hole, the frame is an elliptical hole, and the other frames are approximately rectangular holes. The pass section is composed of circular arc. Professional projects include: square pipe, square pipe, seamless square pipe, galvanized square pipe, galvanized pipe and other related businesses. Please welcome merchants who want to have this business. And the arc radius increases frame by frame, The fillet radius of the joint between the side wall and the bottom of all pass patterns is equal to the fillet radius of the finished section. The total elongation coefficient of the square tube is about 05, which is mainly distributed on the flat roller. The deformation of the vertical roller is very small, and its function is to press down the short side of the square tube. With this design, the calculation is complex and the calculation value is not accurate enough. It is necessary to constantly correct the pass circumference.

Square pipe is an important type of square pipe, which has great similarities with seamless steel pipe, but it is different. Square pipe is of great use in square pipe, which is generally used in the field of building materials and pipes. Today we tell you about the painting of square pipe. In fact, most manufacturers need to do this function, not only painting but also galvanizing. Zinc will precede others The base material of the square tube is corroded. If painting is not for you, it will cost you two money. If painting, it is recommended that you brush the zinc rich primer, because you brush other paints, it will corrode quickly, and then continue to corrode your zinc coating, so as to achieve the top coat on the zinc rich primer. In fact, you should brush the zinc rich primer before galvanizing

Shawinigan.Square tubes shall be stored with supports,ShawiniganHow much is a galvanized pipe, products and tens of millions of products for you to choose. Professional square tubes, square rectangular tubes, seamless square tubes, galvanized square tubes and galvanized tubes are safe and secure. They shall be at a certain distance from the ground to ensure the ventilation of square tubes.

High productivity of square tube: the efficiency of cold production of mechanical parts is very high, especially for parts with large batch. Cold production can be several times, several times or even hundreds of times higher than cutting. For example, the use of cold pin for automobile is twice higher than that of cutting. At present, cold pin automata is used to improve productivity. The productivity of table cooling automata is equivalent to that of 100 ordinary lathes or 10 shaft self-propelled machines.

The cutting surface of the square tube shall be true circle, and the cutting line shall be at right angles to the axis of the square tube. Excessive force is the reason for cutting the square tube into flat or oval, so the square tube should be cut with appropriate force.