StocktonSC hot dip galvanized steel pipehighly recommended

Q355b square tube, the selected die material, has obvious hardening in the deep drawing process, resulting in many hard metal points, resulting in adhesion. Special products such as professional square tube, square rectangular tube, seamless square tube,Stockton4-point galvanized square pipe, galvanized square tube and galvanized tube are 20-year-old brands, so tool steel for general die can not be used.

In terms of hot working, repeated upsetting and multi-directional rolling of ingot can not only reduce the level of carbide segregation in square tube, but also improve the anisotropy of steel.

Stockton.A. square tube structural steel: (a) high quality carbon structural steel; (b) Alloy structural steel; (c) Spring steel; (d) Easy cutting steel; (e) Bearing steel; (f) High quality structural steel for specific purposes.

The general delivery length of square pipe is 3200mm-13000mm, mostly 65000mm and 13000mm. The square tube is allowed to deliver short and non fixed length products not less than 2300mm, or in the form of interface tube, but the Demander shall cut off the interface tube when using it. The allowable deviation of the wall thickness of square pipe shall not exceed plus or minus 10% of the nominal wall thickness when the wall thickness is not greater than 10mm, plus or minus 8% of the wall thickness when the wall thickness is greater than 10mm, except for the wall thickness of corners and weld areas. The weight of short gauge and non fixed gauge products shall not exceed 8% of the total delivery. For square tubes with a theoretical weight greater than 20kgm, we can correctly select the appropriate application field, In this way, the use efficiency of square tube can be improved. Next, we will mainly explain the characteristics of pipe cooling technology below. What are the main characteristics of square tubes? Square tube parts have accurate dimensions and smooth surfaces: the dimensional accuracy of cold parts developed at present can reach grade 8 ~ 9. If ideal ones are adopted, their accuracy is second only to that of fine polished surfaces. Therefore, cold parts generally do not need to be reprocessed, and a small amount only need finishing (grinding).

.The q355b square tube protective layer thickness detector is used to measure the actual thickness of the seamless q355b square tube protective layer on site. It is required that the actual thickness of the seamless q355b square tube protective layer of the seamless q355b square tube shall not be lower than the design value. When the requirements are not met, the protective layer of seamless q355b square tube can be chiseled and measured.

The quality of the solid square tube after the square tube formwork removal and curing can be tested according to the requirements and the following ways: use a magnifying glass to observe whether there are non external force cracks on the structural surface of the solid seamless q355b square tube. When non external force cracks appear on the surface of q355b square pipe, the crack width on the structural surface of ordinary q355b square pipe shall not be greater than 0.20mm.

The strength, plasticity and angle discussed later are the machine function indicators of metal under static load. In practice, many mechanical machines are under repeated load, and the whole opportunity is tired in this environment.

The q355b square tube protective layer thickness detector is used to measure the actual thickness of the seamless q355b square tube protective layer on site. It is required that the actual thickness of the seamless q355b square tube protective layer of the seamless q355b square tube shall not be lower than the design value. When the requirements are not met, the protective layer of seamless q355b square tube can be chiseled and measured.

Generally, chemical and electrolytic methods are used

Mechanical properties of seamless q355b square tube: tensile strength & sigma; b (MPa)：≥ 980 yield strength & sigma; s (MPa)：≥ 835 elongation & Delta; 5(%)：≥ 12 reduction of area & psi; (%)：≥ 40 impact absorption energy (impact value) (aku2j): & Ge; 39 the products produced by the more complex technology are exquisite. At present, Fangguan is highly praised by the public in the market. What is important is that there is a good guarantee in terms of quality. Therefore, whether Fangguan can obtain such a high market evaluation depends on the complex technology of Fangguan.

Focus on Development.It is forbidden to degrease the oil square pipes and pipe fittings in the direct production concentration unit, air separation unit, oil refining and chemical engineering according to the design requirements. The purpose of degreasing is to prevent the transported or stored materials from being contaminated by grease or organic matter; Avoid mixing transported or stored materials with grease or organic matter; Oil content to ensure the activity of the catalyst; The content of oil and organic matter to ensure the purity of the product. The installed square pipe shall be disassembled into pipe sections for degreasing. Pipes that cannot be disassembled after installation shall be degreased before installation. Square pipes with obvious oil stains or serious corrosion shall be cleaned by steam purging, sand blasting or other methods before degreasing.

Solid bending, as the name suggests, is to compact the bending. During real bending, the inner and outer rollers and the inner and outer walls of the pipe blank are compacted in both directions.

Functional index analysis of square tube - commonly used are square tube Brinell angle (HB), Rockwell angle (hrahrbhrc) and Vickers angle (HV) Equal angle is a gauge needle to weigh the soft and hard level of metal data. In the current life, the angle method is rarely used to determine the angle. It uses the indenter with a certain number and shape to determine the angle value of the metal data surface being tested under a certain load according to the level.

To sum up improving the quality level of square tube is the key to ensure the service life of die. Therefore, the quality level of square tube, including surface quality and internal quality, should be improved as much as possible by using more mature process measures.

agent.All seamless q355b square tubes shall be tested for mechanical properties. Mechanical property tests are mainly divided into two categories: tensile test and hardness test.

Fake and shoddy square tubes are easy to scratch because the equipment of fake and shoddy material manufacturers is simple and easy to produce burrs and scratch the surface of square tubes. Deep scratches reduce the strength of square tubes.

Before gas cutting, remove the dirt and grease on the steel surface, and leave a certain space below to facilitate the blowing out of slag. During gas cutting, the movement of the cutting torch shall be kept at a uniform speed. The cutting surface should be 2 ~ 5mm away from the tip of the flame core. If the distance is too close, the edge of the cut will melt, and if it is too far away, the cutting will be interrupted easily due to insufficient heat.

Stockton.In case of doubt about the strength of solid q355b square tube, it can be based on tb10426 & mdash; 200 the compressive strength of q355b square tube on the surface of the structure is indirectly measured by the post loading method. The measurement should be carried out at the age of about 56 days and the measured average strength is required to be not lower than the design value or the specified value. When the requirements are not met, the core drilling sampling method can be used for verification.

Square tube failure. When the pipeline is erected,StocktonGalvanized square pipe, it is necessary to do a good job or directly use the square pipe. The reason for the corrosion of the pipeline is that the layer of the pipeline is damaged. Once the layer is separated from the pipe surface, mostly 65000mm and 13000mm. The square tube is allowed to deliver short and non fixed length products not less than 2300mm, or in the form of interface tube, but the Demander shall cut off the interface tube when using it. The allowable deviation of the wall thickness of square pipe shall not exceed plus or minus 10% of the nominal wall thickness when the wall thickness is not greater than 10mm, plus or minus 8% of the wall thickness when the wall thickness is greater than 10mm, except for the wall thickness of corners and weld areas. The weight of short gauge and non fixed gauge products shall not exceed 8% of the total delivery. For square tubes with a theoretical weight greater than 20kgm, it shall not exceed 5% of the total delivery. We have many different ways in square tubes. Different ways make square tubes have different characteristics. According to these characteristics,StocktonQ235 galvanized square pipe, we can correctly select the appropriate application field, In this way, the use efficiency of square tube can be improved. Next, we will mainly explain the characteristics of pipe cooling technology below. What are the main characteristics of square tubes? Square tube parts have accurate dimensions and smooth surfaces: the dimensional accuracy of cold parts developed at present can reach grade 8 ~ 9. If ideal ones are adopted, their accuracy is second only to that of fine polished surfaces. Therefore cold parts generally do not need to be reprocessed, and a small amount only need finishing (grinding).