ZendehJanPP square tubeMore favorable price

The general delivery length of q355b square pipe is 4000mm-12000mm, mostly 6000mm and 12000mm. Q355b square tube is allowed to deliver short and non fixed length products not less than 2000mm, or in the form of interface tube, but the Demander shall cut off the interface tube when using it. The weight of short length and non fixed length products shall not exceed 5% of the total delivery. For q355b square tube with theoretical weight greater than 20kgm, it shall not exceed 10% of the total delivery. The bending degree of q355b square tube shall not be greater than 2mm per meter, and the total bending degree shall not be greater than 0.2% of the total length. The square tube is classified according to the production process: hot rolled seamless square tube, cold drawn seamless square tube, seamless square tube and square tube.

Of course, since the q355b square tube material is selected as the base metal, it generally has special purposes so the welding materials will not be selected casually. It is better to use it according to the welding material manual. If the welding rod manual says that the base metal should be preheated, the weld performance will be greatly reduced.

ZendehJan.The difference between hot-dip galvanized square pipe and cold-dip galvanized square pipe is mainly from the following aspects: the appearance of hot-dip galvanized square pipe is slightly rough compared with cold-dip galvanized square pipe; The appearance of cold galvanized square pipe is smooth and bright.

Galvanized q355b square pipe for low pressure fluid transmission, Standard No.: gbt3092-2008. The representative material is the same as above. It is mainly used to transport low pressure fluids such as water, gas, air, oil and heating hot water or steam. The surface of square pipe adopts hot galvanizing or cold galvanizing process.

.Square pipe is an important pipe. Its application in various fields has different performance. According to its different performance, we have carried out different transformation on the other pipe to ensure that the square pipe can be better used. We should make the right choice when purchasing. Below I will introduce the correct way of painting the lower pipe.

The strength, plasticity and angle discussed later are the machine function indicators of metal under static load. In practice, and the whole opportunity is tired in this environment.

Hardness test is to use a hard indenter to slowly the sample surface according to the specified conditions and then test the indentation depth or size, so as to determine the hardness of the material. Hardness test is simple,ZendehJan125 square tube, rapid and easy to implement in material mechanical property test. Hardness test is non-linear, and there is an approximate conversion relationship between material hardness value and tensile strength value. The hardness value of material can be converted into tensile strength value, which is of great practical significance.

In the process of processing, the processing temperature is the key. Professional square tube, square tube, seamless square tube, galvanized square tube and galvanized tube have advanced technology, more affordable price and more preferential price. Consultation is welcome. It must be noted that the blank heating should be uniform. Perforation has a great impact on the quality. The perforation temperature of blank varies according to different materials, generally around 1200 ℃.

High quality steel (P & le; 0.035%, S & le; 0.030%)

Functional index analysis of square tube - mechanical function of plastic square tube.

A complete range of products.Performance index analysis of square tube - hardness is an indicator to measure the hardness and softness of metal materials. At present the hardness method is commonly used to measure the hardness in production. It uses the indenter with fixed geometry to measure the hardness value of the metal material surface tested under fixed load according to the degree of hardness.

It is a kind of cleaning for the surface of square pipe. Shot blasting is often used to clean the casting surface or strengthen the surface of square pipe.

Before gas cutting, remove the dirt and grease on the steel surface, and leave a certain space below to facilitate the blowing out of slag. During gas cutting,ZendehJanGalvanized 20 square pipe, the movement of the cutting torch shall be kept at a uniform speed. The cutting surface should be 2 ~ 5mm away from the tip of the flame core. If the distance is too close, the edge of the cut will melt, and if it is too far away, the cutting will be interrupted easily due to insufficient heat.

The detailed steps for cutting square tubes are as follows: what is used for cutting square tubes? Seamless square tubes can only be processed successfully after certain steps in processing and engineering. The first step that must be experienced in processing is to cut seamless square tubes. There are various cutting methods for seamless square tubes. Today, I'd like to introduce a method of cutting seamless square tubes with slices, It is recommended to cut according to the following provisions: select a uniform surface to select potatoes; The large diameter is not too much, slightly larger ones, and small needles. Sometimes large potatoes are not long enough; C. select flat, sink and vegetable board. When it is uneven, it will be cut continuously; When the texture is light cut, the die-cutting board will follow.

Administration.High temperature diffusion heat treatment of ingot can improve the composition heterogeneity of ingot and improve the transverse performance of square tube.

Impact toughness the load acting on the machine part at a great speed by Q235B is called impact load, and the ability of metal under impact load is called impact toughness.

Both internal and external welding of square pipes are carried out by American Lincoln Electric welding machine for single wire or double wire submerged arc welding,ZendehJanQ345E seamless square tube, so as to obtain stable welding specifications.

ZendehJan.Square tube flattening test is a kind of test to check the deformation performance of metal tubes (seamless square tubes and rectangular tubes) flattened to the specified size and show their defects. Relevant flattening tests shall be carried out in accordance with relevant provisions of test standards. Requirements for samples samples can be taken from metal pipes with qualified appearance. Generally, sawing is adopted. The inner and outer walls of the pipe shall retain the original surface without any processing. Sample length L & asymp; D (D is the outer diameter of the pipe). When the outer diameter is large, the length l shall not exceed 100mm. When the outer diameter is less than 20mm, l = 20mm. When cutting the sample, the surface of the sample shall not be damaged and the performance of the metal shall not be changed due to heating or cold processing. The edge of the section shall be flattened. The flattening test is a test to check the deformation performance of the metal pipe (seamless square pipe and rectangular pipe) flattened to the specified size and show its defects. Relevant flattening tests shall be carried out in accordance with relevant provisions of test standards.

Among them, q355b square tube is divided into process & mdash& mdash; Arc welded square pipe, resistance welded square pipe (high frequency and low frequency), gas welded square pipe and furnace welded square pipe are divided by weld & mdash& mdash; Straight seam welded square pipe, spiral welded square pipe.

The standard number of spiral square pipe (standard of the Ministry of petroleum) for low pressure transmission is syt5037-2008. The representative materials are q235bq345b and other carbon steel materials. It is mainly used for low-pressure transmission of water, oil, natural gas, heating and other pipelines.