SilversonAlumi
SilversonFour It is strictly prohibited to run the engine for a long time in a closed garage. The exhaust gas of the aluminum alloy elevator engine contains carbon monoxide. This is a toxic gas that has been in low concentration for a long time
Pay attention to checking each steel wire rope for broken wires and loose strands. If it exceeds the relevant regulations, it must be replaced immediately. The maintenance and upkeep of steel wire ropes should strictly follow the provisions of GB5144-85.
Silverson.According to the classification of mobile, fixed,SilversonAluminum alloy lifting door, telescopic table top, wall mounted elevator folding elevator, wall mounted elevator, car mounted (diesel), self-propelled and other aluminum alloy elevators.
It is strictly prohibited to run the engine for a long time in a closed garage. The exhaust gas of the aluminum alloy elevator engine contains carbon monoxide. This is a toxic gas that has been in low concentration for a long time
.Method for hydraulic oil leakage in aluminum alloy elevator: Check if the pipe joints are loose and try to tighten them. Check if the viscosity of the hydraulic oil used is too low. When checking the leakage point of the hydraulic oil system, generally, the place where hydraulic oil seeps out is the leakage point, but it is not ruled out that the leaked hydraulic oil may accumulate along the pipeline deviating from the leakage point. Therefore, it is important to carefully search during inspection. High priced aluminum alloy elevator manufacturers of various specifications welcome scrap merchants, industrial companies, enterprises, and power departments to visit and negotiate with the company!
. Before the maintenance of the hydraulic aluminum alloy elevator starts, the tools used must be counted. After the maintenance is completed, the tools should be classified and organized, and counted to prevent the tools used for maintenance from being left inside the equipment, especially in the distribution box. When repairing the hydraulic system of the aluminum alloy elevator, it is necessary to keep the maintenance site clean and dust-free. When repairing and fastening screws for aluminum alloy elevators, it is necessary to use the correct diagonal first. When tightening screws, use a torque wrench to prevent excessive damage to the screws. After the maintenance is completed and before the power on test, inspecting and repairing the equipment and the maintenance site, the power transmission test can only be carried out. After the maintenance of the aluminum alloy elevator is completed, the equipment maintenance record must be filled out. The maintenance record should include the equipment maintenance date the personnel participating in the maintenance, the brand, model and specification of the replaced parts, the effectiveness of the maintenance, and whether the equipment still has problems after the maintenance is completed.
Method: Check the length or diameter of the power supply lead. When the wire length is not more than 25 meters, the wire diameter should not be less than 1m ²; When the wire length is not greater than 50 meters, the wire diameter should not be less than 5m ². You can try fixing the plug directly to the socket without moving the cable.
Regularly check the connection of each part and tighten it if there is any looseness. The tightness of the body connecting bolts should be checked when the body is under pressure (the rotating arm can be used to cause compression), and all connecting shafts must have split pins and be sufficient. Professional items
Single column aluminum alloy elevator: This series of products is indoor and widely applicable to the elevator tables in various industries such as star hotels and large supermarkets. It has balanced lifting and easy operation, and can enter and exit the elevator at will, with low power consumption, no pollution, and no damage to the ground during work. It can be used for double column aluminum alloy elevators to stick to walls and explore operations, without any dead corners during work. The single column aluminum alloy electric elevator, equipped with gantry cross frame accessories, auditoriums, etc. The gantry frame is easy to assemble, labor-saving to operate, capable of crossing obstacles such as fixed seats with a height of up to 1m, and can operate stably on steps. Made of high-strength rectangular steel pipes, with good rigidity and stability. Equipped with universal casters for flexible mobility. The span of the two end brackets can be adjusted, which is suitable for crossing different obstacles. The two end brackets are vertically adjustable and can be used for operations on slopes or steps with a certain slope.
Users can choose the power mode and configuration according to their usage range: the power system includes: DC power supply, single-phase or three-phase power supply, diesel engine. Walking: assisted self-propelled two wheel traction, self driving, and car modification. Outriggers: mechanical outriggers, hydraulic outriggers, ordinary hand cranked outriggers, and pull-out outriggers. System: explosion-proof electronic control system, remote control system, PIC system. Hydraulic pump station: domestic lifting platform dedicated pump station, mesh type, and iron plate sealed type.
Home page recommendation.On the friction surface, there should be no dirt present, and any dirt must be washed off with gasoline or thinner.
Is the power source noise abnormal during the lifting process of the aluminum alloy elevator?
The standard rack free design of the lifting and lowering machine with high safety performance ensures that the platform will not fall,SilversonAluminum alloy hydraulic elevator, and the limit and limit switches further ensure the safety of construction personnel.
Check if the power supply voltage is below the allowable value.
Inspection standard.The time and price of aluminum alloy elevators will also be determined based on the order cycle of the product. Compared to aluminum alloy elevators, many customers find it difficult to obtain the corresponding product model at that time. Because many customers have to use the product within a limited time, they will choose product suppliers with fast delivery and short delivery times. Aluminum alloy elevator manufacturers often produce their products on a seasonal basis. So many customers are present and the manufacturer does not have stock, so they need to reschedule production, with production cycles ranging from 2 to 3 months. And those suppliers who have stock will also consider the factor of customers not being in a hurry to increase the price of aluminum alloy elevators.
Additionally, it should be noted that there will be a box and a distribution box inside the elevator.
According to the number of masts,SilversonAluminum alloy lifting machine table, it can be divided into: single mast aluminum alloy lifting platform: supported by single mast operating platform which is an early aluminum alloy elevator. The entire machine is light in weight and flexible in movement, suitable for single person operation. After condensation, it can enter general standard doorways and elevators in buildings.
Silverson.Multi mast aluminum alloy lifting platform: the whole platform is refined by high-strength aluminum profiles. Due to the high strength of the profiles, the four mast structure is adopted, which has excellent stability, flexible operation, large load capacity, large platform area and convenient implementation. Its appearance allows for high lifting capacity in extremely small spaces. Minimize the deflection of the lifting platform.
Good driving performance reduces noise, increases the clearance inside the platform, and also makes the transmission smoother and the mechanism vibrates less.
Firstly, unstable voltage can easily burn out various electrical components inside the operation box, making the equipment unable to receive signals.