TaiwanFixed hy
TaiwanHydrauliThe characteristics of the platform include reliable hydraulic system, simple operation, large load-bearing capacity, and rear hinge support.
Due to damage to the gear pump of the lifting cargo elevator equipment and no pressure lifting. Replace the gear pump.
Taiwan.Today, we will share with you why hydraulic cargo elevators are ideal equipment for transporting goods?
The above are the working principles of three common elevators, and there are also some forms of elevators that are not common, such as cylinder mounted elevators, curved arm elevators, etc. Their common feature is the hydraulic principle for operation, because the stability of the hydraulic system can bring better user experience and safer operation to the equipment, which has been favored by many users.
.The above are the working principles of three common elevators, and there are also some forms of elevators that are not common, such as cylinder mounted elevators,TaiwanDouble shear hydraulic lifting platform, curved arm elevators, car mounted elevators, etc. Their common feature is the hydraulic principle for operation because the stability of the hydraulic system can bring better user experience and safer operation to the equipment, which has been favored by many users.
Considering the oil level in the oil tank, when all hydraulic cylinders in the system are extended the oil level in the oil tank should not be lower than the Z-low oil level, and when the oil cylinders retract, the oil level should not be higher than the Z-high oil level. In fact, most manufacturers have noticed the above issues. The reason for the introduction is that most users can learn more about the equipment itself when using elevators, in order to facilitate equipment maintenance. Hydraulic cargo elevator manufacturers sincerely hope that you choose a legitimate manufacturer when purchasing elevators, to avoid any worries about after-sales service.
The cylinder head oil seal is too tight or the rod is bent, which can also cause noise during movement due to other forces. At this point, the oil seal or straightening rod must be replaced in a timely manner.
Considering the oil level in the oil tank, the oil level in the oil tank should not be lower than the Z-low oil level,TaiwanHydraulic guide rail lifting platform, the oil level should not be higher than the Z-high oil level. In fact, most manufacturers have noticed the above issues. The reason for the introduction is that most users can learn more about the equipment itself when using elevators, in order to facilitate equipment maintenance. Hydraulic cargo elevator manufacturers sincerely hope that you choose a legitimate manufacturer when purchasing elevators, to avoid any worries about after-sales service.
Based on experience, new steel wire ropes will not suddenly break when used under normal circumstances, unless incorrect operation or safety protection devices fail, as the load borne by the steel wire may exceed its breaking capacity. The damage to the steel wire rope of the cargo elevator is mainly gradually formed during long-term use. After a certain period of repeated bending and friction, the steel wire on the surface of the steel wire rope will experience bending fatigue and wear, and the steel wire on the surface layer will gradually break. At this point, if it cannot be used again, it should be replaced in a timely manner to ensure the safety of the hydraulic platform.
When using an electric mobile scissor lifting platform outdoors, if the wind force exceeds level 5, please stop using it; When the lifting height exceeds 10 meters, and the support legs should be reinforced for protection and stability to avoid safety accidents caused by excessive swinging of the electric lifting platform
Online consultation.The hydraulic oil used in the system has the same brand, and the oil temperature is between 45~80 ℃. Use a large flow rate to remove impurities from the system as much as possible. The hydraulic system needs to be cleaned repeatedly three times or more, and after each cleaning, the system should be drained while the oil is hot. After cleaning, clean the filter and add new oil after using a new filter element.
Pay attention to checking each steel wire rope for signs of broken wires and loose drums. If it exceeds the relevant rules, it is necessary to replace it immediately. The protection of steel wire ropes should strictly follow the rules of GB5144-85.
There are many reasons for unstable workbench descent, such as overload, unstable support, severe eccentric load hydraulic oil impurities,TaiwanDouble fork hydraulic lifting platform, etc. In response to the above reasons, it can be solved by reducing the load, adjusting the center of gravity of the load, and replacing hydraulic oil wholesale for hydraulic cargo elevators.
Stability: The workbench should evenly withstand 125% of the MAX load capacity and be stable at the MAX elevation.
Good reputation.Each brush should be kept clean on its surface, and the brush pressure should be adjusted to ensure that its area is not less than 50%.
Lift and move horizontally with load to return to the loading position. For the transportation time of each item, such repeated cycles are called cycles.
The characteristics of the platform include reliable hydraulic system, simple operation, large load-bearing capacity, and rear hinge support.
Taiwan.When using an electric mobile scissor lifting platform outdoors if the wind force exceeds level 5, please stop using it; When the lifting height exceeds 10 meters, the wind ropes at the four corners of the hydraulic lift platform should be tightened and fixed, and the support legs should be reinforced for protection and stability to avoid safety accidents caused by excessive swinging of the electric lifting platform
Car mounted lifting platform: The car mounted lifting platform is designed to improve the mobility of the lifting platform by fixing it to a transport vehicle or truck. It receives power from the car engine and achieves the lifting function of the car mounted lifting platform. To adapt to high-altitude operations inside and outside the factory area.
When encountering signs of overheating in the electric motor, it is necessary to park the car in a timely manner, clean the problem, and continue running. The motor bearings should be smooth and outstanding.