TaiwanHydrauli
Taiwan6-meter TaiwanManufacturer of scissor lift,
Load bearing capacity: The lifting platform is placed on a horizontal support surface, and the workbench is evenly loaded to 125% of the maximum load capacity. After lifting 100 times, each load-bearing component must not have deformation or cracks.
After 1500 hours of elevator operation perform minor repairs to the mechanical and electrical systems.
Taiwan.Due to the formation of a flow closed-loop, the volumetric speed regulation hydraulic elevator has good performance and high load stiffness. The hydraulic system using the volumetric speed regulation scheme has a higher efficiency and greater energy loss compared to the throttling scheme, as its output power is roughly equal to the power required for the elevator to move up. But using an elevator volume speed control system can only reduce the energy consumption during the upward process of the elevator. When the elevator goes down, the oil in the cylinder moves down the throttle valve under pressure, which will cause the temperature of the hydraulic system to rise. Not to mention anything else, just an intelligent alarm is enough to demonstrate the true value of hydraulic elevators.
For hydraulic cylinders in hydraulic elevators, it is not practical to change their effective working area A (equivalent to displacement) to adjust the speed. Generally, the speed can only be adjusted by changing the flow rate. For variable displacement motors, speed regulation can change both the flow rate and the motor displacement.
.Electrical equipment or component failures. Hydraulic elevator manufacturers tell you that the main reasons for high noise generated by electric motors are: bent or severely worn motor rotors, or damaged bearings, which cause electric motors to sweep and produce noise; The cooling fan of the electric motor is damaged or not firmly fixed, resulting in high noise; The electric motor is not firmly fixed and can also cause vibration, producing high noise.
The lifting platform is placed on a horizontal support surface, and the concentrated load of MAX load capacity is placed at any position 300mm away from the periphery of the workbench. After lifting 100 times, each load-bearing component must not have deformation or cracks.
Do not use hydraulic lifting equipment with malfunctioning issues. The problem should be resolved before carrying cargo.
There is a phenomenon of self stopping when running up and down. Due to poor contact of the safety protection switch it is easy for hydraulic cargo elevator manufacturers to cause this problem.
Below, we will analyze for everyone. According to the market survey and understanding conducted by the editor of hydraulic freight elevator manufacturers, many customers choose hydraulic elevators instead of elevators due to the following reasons: narrow transportation location, which cannot meet the requirements of elevators; Unable to excavate the elevator shaft at the working location; Elevators are expensive and difficult to meet their needs.
Mobile is a type of cargo heavy machinery equipment with good adjustment reliability and wide application fields, suitable for automated production lines
Honesty is the foundation.After long-term use of the automatic lifting platform equipment, it is inevitable that some malfunctions will occur. In order not to affect work, it is necessary to promptly solve the difficulties in starting the motor and abnormal sounds. Generally, due to overload, insufficient power supply, and a small cross-sectional area of the power supply cable, the starting voltage drop is too large and the price of the cargo elevator is reduced.
Check valve leakage: If the natural wear of the check valve exceeds the specified value after long-term use, it will cause leakage. Disassemble and clean the check valve, and replace it if necessary.
The lifting platform is placed on a horizontal support surface, and the concentrated load of MAX load capacity is placed at any position 300mm away from the periphery of the workbench. After lifting 100 times, each load-bearing component must not have deformation or cracks.
When disassembling and adjusting the reverse organization of the equipment, attention should be paid to ensuring that the centerline of the reverse organization reducer is parallel to the centerline of the gear, and its meshing surface is not less than 70%. The meshing gap should be appropriate.
Installation material list. There is air in front of the pilot valve of the elevator overflow valve noise overflow valve. The damping hole on the main valve core of the overflow valve is blocked by oil dirt, and the pilot valve and valve seat are matched without spring deformation or incorrect installation. The remote control port has excessive oil flow, low or high hydraulic oil viscosity, and resonance occurs with components in the circuit. Troubleshooting: Strengthen sealing, repeatedly adjust the pressure, exhaust and clean the valve body several times, Make the damping hole unobstructed, repair or replace the spring,TaiwanCylinder mounted hydraulic lifting platform, reduce the flow of the remote control port, replace the oil, and other components. The pressure setting of other components should not be similar to the pressure setting of the relief valve. 5. The noise of the elevator pipeline is usually caused by excessive dead bends or loose fixed sleeves in the hydraulic pipeline.
When the hydraulic cargo elevator needs to work, first connect the power supply and press the button to drive the motor of the hydraulic power unit to drive the gear pump. The hydraulic oil forms a certain pressure through the vane pump and passes through the oil filter; Explosion proof electromagnetic directional valve; Throttle valve; Hydraulic control one-way valve; The balance valve enters the lower end of the hydraulic cylinder, causing it to move upwards and lift heavy objects. The hydraulic cylinder moves downwards (i.e. the weight drops),Taiwan8-meter hydraulic lifting platform, the explosion-proof electromagnetic directional valve of the hydraulic oil enters the upper end of the hydraulic cylinder, and the return oil from the lower end of the hydraulic cylinder passes through the balance valve; Hydraulic control one-way valve; Throttle valve, explosion-proof electromagnetic directional valve.
The smoothness of the gearbox gearbox, external meshing gears, and hydraulic oil are all carried out according to the requirements in the smoothness table.
Taiwan.The hydraulic lifting platform often checks the connection status of each part, it should be tightened. The connection bolts of the machine body should be checked for tightness when the elevator body is under pressure (the compression condition can be formed by rotating the arm). All connecting shafts need to have split pins and need to be fully opened.
Therefore, in the hydraulic pipeline assembly line