The cold rolled steel strip has good strength and yield ratio, and the hot rolled steel strip has good ductility and toughness.
347h chemical composition carbon C: Manganese Mn: silicon Si: chromium Cr: nickel Ni: phosphorus P: sulfur s: niobium NB: 347h stainless steel Name: austenitic stainless steel standard: aisastm model: 347huns No.: Note: a single value is a high value unless otherwise indicated; when used in some pipe making processes, the nickel content of some models of austenitic stainless steel must be slightly higher than that shown in the table; optional High TA content is 0.10%; high content is 0.75%; high content is the basic characteristics of stainless steel, with high temperature strength and high temperature plasticity, excellent oxidation resistance and corrosion resistance, uniform chemical composition, good processing performance and welding performance, high dimensional accuracy and surface quality. 5 causes of rust when brown spots appear on the surface of stainless steel They were greatly surprised: & rdquo; stainless steel will not rust. Rust is not stainless steel. There may be something wrong with the steel quality. & rdquo; in fact, this is a one-sided wrong view of the lack of understanding of stainless steel. Stainless steel will also rust under certain conditions
.The shape of pipe end stainless steel pipe can be divided into smooth pipe and threaded pipe (threaded steel pipe) according to the state of pipe end. Threading pipe can also be divided into ordinary threading pipe (pipe for conveying low pressure such as water and gas, which is connected by ordinary cylindrical or conical pipe thread) and special threaded pipe (pipe for petroleum and geological drilling, which is connected by special thread for important threading pipe). For some special pipes, in order to make up for the impact of thread on the strength of pipe end, the pipe end is usually thickened before threading (inner thickening, outer thickening or inner and outer thickening).
Before connecting the pipe fittings, mark the depth on the pipe first, so as to prevent it from being inserted in place and stuck.
.Cold rolled steel strip shall be delivered in the state of heat treatment (annealing, normalizing and tempering after normalizing), and shall be delivered smoothly.
mdash; Martensitic precipitation hardening stainless steel.
For example, if the actual thickness of stainless steel 51 round pipe is 0.9, the weight of a single 6-meter-long stainless steel pipe is (51-0.90.920.024916 = 87kg, and the theoretical weight of a 6-meter-long 51 round pipe is 0.92. For example, the weight of a single 6-meter-long stainless steel pipe of stainless steel square pipe 7545 with a thickness of 0.92 is [(75 + 4214-014-0.920.920.024916 = 38kg). If the weight of stainless steel pipe per meter is calculated, the length can be changed into one meter.
In the building water supply pipe system, since the galvanized steel pipe has ended its glorious history of one hundred years, various new plastic pipes and composite pipes have developed rapidly. The professional stainless steel plate, stainless steel coil, stainless steel belt and stainless steel pipe have advanced technology, strict testing, more affordable price and more preferential treatment. Welcome to consult. However, there are still some deficiencies in various pipes to varying degrees, It is far from fully meeting the needs of water supply pipeline system and national requirements for drinking water and related water quality. Therefore, relevant experts: building water supply pipes will eventually return to the era of metal pipes. According to foreign application experience, stainless steel pipe is recognized as one of the pipes with good comprehensive performance in metal pipe. Chemical analysis: carry out chemical analysis on the chemical composition of the material, and the chemical composition meets the requirements
For business people of course, it is better to spend less under feasible conditions. For goods such as stainless steel pipes, we can often see that there will be packaging film bags on them. Although they are not heavy, if there are a large number of single purchases, they will also produce certain economic expenses, but why do many people clearly dislike this thing on stainless steel pipes, xincoral Xiaobian will tell you why stainless steel pipes need packaging bags.
Stainless steel pipe national standard thickness in the stainless steel pipe industry, the steel that meets the national standard is generally called & ldquo; National Standard & rdquo; Inferior steel that does not meet national standards is called & ldquo; Winning the bid& ldquo; Non standard & rdquo; In practical application, the quality of national standard and non-standard is similar mainly due to the difference in thickness. A thickness of national standard is actually 1mm, but a thickness of non-standard is actually only 0.8mm or other thickness less than 1mm. Non-standard is basically equivalent to winning the bid. Standard index size (323mm) label number standard implementation standard gbt14976-2012 non-standard specific thickness ratio outer diameter steel pipes are produced according to the standard. 2 non-standard belongs to customized difference. Wood office says ha ha customized on demand. 3 thickness area: the difference between standard, stainless steel American Standard and national standard mainly lies in C content and P content; The C content and P content of Chinese standards are lower than those of American Standard ASTM A312@_@ The two important elements of material are chromium and nickel, 15 9 large plants and 18 8 large plants of national standard and 18 8 small plants of American Standard 132@_ @ The national standard contains more than 17 chromium and the American Standard contains more than 18 chromium@_@ Stainless steel pipe is an American Standard, not in the national standard. The corresponding national standard is 06cr19ni10.
Customer first.The resistance, linear coefficient, thermal conductivity, quality, hot melt and magnetism of stainless steel pipe will change greatly at low temperature. Resistance, line coefficient decreases at low temperature; The thermal conductivity and mass heat capacity decrease sharply at low temperature; Young's modulus (longitudinal modulus) increases when the temperature decreases. Because the austenitic series stainless steel pipe has MS point (martensite start temperature or martensite formation temperature) at low temperature (subzreo temperature), martensite can be formed when it is kept below MS point. The formation of martensite at low temperature makes the representative steel sus (18Cr-8Ni) of austenitic stainless steel non-magnetic at room temperature and magnetic at low temperature.
Theoretical weight of stainless steel pipe: w = outer diameter - wall thickness x wall thickness x0.02491.
5cm thick stainless steel plate shall be processed with special cutting tools, such as laser cutting machine with large wattage
Check whether the sealing ring of pipe fittings is complete and clean and whether the placement position is correct. If there is dirt it must be cleaned up. If the sealing ring is damaged, it must be replaced again.
Finance Department.In order to ensure that the mechanical properties such as yield strength, tensile strength, elongation and hardness of various stainless steel coils meet the requirements, the stainless steel coils must undergo heat treatment such as annealing, solution treatment and aging treatment before delivery. The corrosion resistance of stainless steel coil mainly depends on its alloy composition (chromium, nickel, titanium, silicon, aluminum, etc.) and the interior of stainless steel coil
The specific steps of continuous casting billet process of stainless steel pipe fittings are as follows: according to different steel grades, the vibration process of mold is matched with protective slag, which can improve the yield of 10%, save energy and shorten the production cycle, so as to improve the yield of molten steel.
Stainless steel is more than twice as high and has enough plastic toughness for forming. The wall thickness of storage tank or pressure vessel made of duplex stainless steel is 30-50% less than that of common austenite, which is conducive to reducing the cost.
.In order to prevent the occurrence of welding pores, the welding parts must be cleaned if there is rust, oil stain, etc.
7. Distinguish between 316L and 304L. There are two kinds of commonly used stainless steel 30316l (or corresponding to the German / European standard 430844036l, the main difference in chemical composition between 316L and 304 is that 316L contains Mo, and it is generally recognized that 316 has better corrosion resistance than 304 in high temperature environment. Therefore, engineers generally choose 316L parts in high temperature environment. However, there is no absolute thing. In concentrated environment, 316L should not be used at any higher temperature! No However, this is a big problem. People who study mechanics have all studied threads. Remember a black solid agent that needs to be applied to prevent threads from biting under high temperature: molybdenum disulfide (MOS), from which two conclusions are drawn: No: [1] Mo is indeed a high resistance material (know what crucible gold is melted in? Molybdenum crucible!). [2] : molybdenum can easily react with high valence sulfur ions to form sulfide. Therefore no stainless steel is super corrosion resistant. In the final analysis, it can react with other substances.
In order to ensure that the mechanical properties such as yield strength stainless steel is a steel with more impurities (but these impurities are more corrosion resistant than steel). If it is steel, elongation and hardness of various stainless steel coils meet the requirements, the stainless steel coils must undergo heat treatment such as annealing, solution treatment and aging treatment before delivery. The corrosion resistance of stainless steel coil mainly depends on its alloy composition (chromium, nickel, titanium, silicon, etc.) and the interior of stainless steel coil