Stainless steel pipe appeared in Foshan Guangdong Province in the tenth generation of the last century. With the rapid development of science and technology in recent decades, stainless steel pipe production is all over the country. Stainless steel pipe is more and more widely used. But in fact, most people, do not know much about the classification and application of stainless steel pipes. Take stainless steel pipe for example.
Mechanical properties when the steel or sample is stretched, when the stress exceeds the limit, even if the stress is no longer increased, the steel or sample continues to have obvious plastic deformation, which is called yield, and the small stress value when the yield phenomenon occurs is the yield point.
.There are mechanical, chemical and electrochemical methods to remove the scale of stainless steel pipe. Due to the complexity of the composition of the scale of stainless steel pipe, it is not easy to remove the scale on the surface and make the surface highly clear and flat. Generally, the removal of the scale of stainless steel pipe should be carried out in two steps the first step is pretreatment and the second step is ash removal.
Cold rolled oriented silicon steel strip (sheet) represents: 100 times of DQ + iron loss value (at the frequency of 50Hz, the waveform is sinusoidal, and the magnetic induction peak value is the unit weight iron loss value of 7T) + 100 times of thickness value. Sometimes, G is added after the iron loss value to represent high magnetic induction. For example, dq133 represents cold rolled oriented silicon steel strip (sheet) with iron loss value of 3 and thickness of 0.3mm. Now the new model is 30q133.
.In order to prevent water from serious pollution during storage and transportation, the water industry now generally uses stainless steel pipes to store and transport water. Because stainless steel pipes have anti rust, high temperature and high pressure resistance and good sanitary performance, stainless steel pipes are slowly used in the industrial field!.
409— Cheap model (British and American), usually used as automobile exhaust pipe, is ferritic stainless steel (chromium steel).
Production process of hot rolled stainless steel strip / coil: 1. Pickling → 2. High temperature rolling → 3. Process → 4. Annealing → 5. Leveling → ⒍ fine cutting → ⒎ packaging → 8. Reach customers.
Allowable depth of straight track: hot rolled and hot-rolled steel pipes with diameter less than or equal to 140mm shall not be greater than 5% of the nominal wall thickness, and the large depth shall not be greater than 0.5mm; cold drawn (rolled) steel pipes shall not be greater than 4% of the nominal wall thickness, and the large depth shall not be greater than 0.3mm.
For example, the price of 10000 tons of goods 04 = 963846 tons = the result example: the price excluding tax of 1 ton of goods = 15800 a ton 04 = 15193077 ~ the total weight of the known coil weight and price = the coil weight price, the thickness of stainless steel plate & Chi; Width & Chi; Long & Chi; 93 e.g. 0 & Chi; 22Χ 44Χ 93 = 42kg stainless steel plate weight per square meter (kg) calculation formula: specific gravity thickness (mm) width (mm) length (m) stainless steel weight per meter (kg) stainless steel pipe calculation formula: diameter (mm) diameter (mm) (correct calculation of the price difference between burr and trimming of nickel stainless steel 0.0062 chromium stainless steel) in the market, the price difference between burr and trimming of stainless steel is usually set at a fixed price. For example, it is generally considered in the market that the price difference between burr and trimming of 201 is 200 yuan tons and that of 201 is 300 yuan tons. In fact, this method is not scientific. In fact, the price difference between burr and trimming of stainless steel is different The correct calculation should be like this.
Low temperature embrittlement --- in low temperature environment, the deformation energy is small. In the low temperature environment, the phenomenon that the elongation and area shrinkage decrease is called low temperature embrittlement. Most of them are produced on the body centered cubic structure of ferrite series.
Equipment maintenance.There are ba face, 2b face, (white skin), (frosted), HL (wire drawing) 8K face and other surfaces with good quality and brightness.
Its plastic toughness is lower than that of austenitic stainless steel, and its cold and hot working process and formability are not as good as that of austenitic stainless steel.
If the thickness of the steel plate is not enough, the professional stainless steel plate, stainless steel coil, stainless steel belt and stainless steel pipe are strictly tested and the quality is guaranteed. The preferential activities are in progress. Welcome to consult. It is easy to bend, which will affect the production of decorative plate. If the thickness is too large and the steel plate is too heavy, it will not only increase the cost of the steel plate, but also bring unnecessary difficulties to the operation. At the same time the allowance that should be left during processing or use of stainless steel plate shall also be considered. The thickness of copper plate is not absolutely consistent, but the thickness of the same steel plate shall be as consistent as possible. Generally, for medium-sized saw plate, the thickness tolerance is 0.05-0.15mm. If the requirements are too strict, the grinding cost will also increase. Generally, it is a structural steel plate with high resistance and high degree. The greater the mechanical damage resistance, the longer the service durability, but the grinding and processing cost is also relatively high.
High temperature oxidation resistance stainless steel plates have high temperature oxidation resistance, but the oxidation rate will be affected by inherent factors such as environment and product form.
Executive standard.Hydraulic saw grinding disc (manual saw wire cutting machine).
Continuous casting shall be adopted for stainless steel pipe fittings, so as to improve the comprehensive yield, and cooperate with out of furnace refining, which significantly improves the production efficiency, omits the blank opening process and saves a lot of energy consumption.
All decreased in varying degrees, the prices of construction wire rod and rebar, which account for a large proportion of China's steel output, fell by 9% and 7% respectively, and the prices of medium and heavy plate and hot rolled coil fell by 7% and 7% respectively.
.Cutting tool level & rdquo; Martensitic steel, an early stainless steel similar to Brinell high chromium steel. It is also used for surgical tools, which can be made very bright.
5 identification number and indication use international chemical element symbols and national symbols to indicate chemical composition. For a long time, stainless steel plate, stainless steel coil, stainless steel belt and stainless steel pipe have complete products, excellent quality and favorable price. Use letters to indicate composition content: for example, China and Russia use fixed digits to indicate steel series or numbers; for example, the United States, Japan, 300 series, 400 series 200 series; the serial number is composed of Latin letters and order