KhemiselKhechnaGalvanized square steel pipeHow to choose equipment

After perforation, continuous rolling or rolling. Take off the pipe after sizing. The conical drill bit of the sizing machine rotates into the steel embryo at high speed to form a steel pipe. The inner diameter of the steel pipe is determined by the outer diameter length of the sizing machine bit. After sizing, the steel pipe enters the cooling tower for water spray cooling. After cooling, the steel pipe will be straightened. After straightening the steel pipe

The square tube represents the large capacity of the metal material under the action of tension, and the calculation formula is: where: FB -- the strong force borne by the sample when it is broken, n (Newton); So -- original cross-sectional area of sample, mm2. Yield point (& sigma; s) the stress of metal material with yield phenomenon when the specimen can continue to elongate without increasing (keeping constant) the force during the tensile process, which is called the yield point.

KhemiselKhechna.Large diameter q355b square tube production standard classification square tube is divided according to production standard: national standard square tube, Japanese standard square tube, British standard square tube, American standard square tube, European standard square tube and non-standard square tube.

Function index analysis of square tube - the strength acts on the parts in a great progress. The load on the parts is called the charge and trap load. The power of square tube destruction under the charge and trap load is called the charge and trap toughness.

.Should choose, it is recommended to match: epoxy zinc rich 50um + epoxy micaceous iron intermediate paint 80um + polyurethane finish paint 60um. In this way according to the standard of iso12944, you can protect the indoor and outdoor environment for 10 years which is not a big problem.

Functional index analysis of square tube - angular plasticity refers to the power of plastic deformation (permanent deformation) without destruction of square tube data under load.

The iron filings and burrs on the cutting section shall be completely removed with a file or appropriate tools to prevent the iron filings and burrs from scratching the rubber O-ring and other accessories when connecting another part.

The q355b square tube rolled from the strip steel through process treatment is generally to unpack, curl and weld the strip steel to form a round tube flatten, then roll the round tube into a square tube, and then cut it to the required length. Nowadays, the forming of q355b square tube has solid bending and empty bending. The bending degree of q355b square tube shall not be greater than 3mm per meter, and the total bending degree shall not be greater than the actual bending of the total length. As the name suggests, the bending is compacted, and the internal and external rollers and the internal and external walls of the tube blank are compacted in both directions during the actual bending.

Steel for construction and engineering according to the classification of use without phase transformation or partial phase transformation of square tube: A. ordinary carbon structural steel; b. Low alloy structural steel; c. Steel reinforcement.

How about the tensile strength of square pipe: square pipe has good tensile strength, tensile strength and sufficient toughness, which makes square pipe stand out in the field of steel pipe. The square tube has great advantages in high temperature, high pressure and even high strength environment. What are its characteristics? We analyze it one by one: tensile strength (& sigma; b) the strong force (FB) borne by the sample during tensile breaking, and the stress (& sigma;) obtained from the original cross-sectional area (so) of the sample is called tensile strength (& sigma; b), and the unit is nmm2 (MPA).

how much.Effective treatment of square tube coating & ldquo; Surface defense line & rdquo; Surface technology and measures square tube coating is used as the back course & ldquo; Surface defense line & rdquo; The surface treatment technologies and measures can be carried out on the basis of other surface treatment technologies or processes. Here's the & ldquo; Surface treatment before coating & rdquo; It refers to all treatment measures for preparation for coating or joint protection with coating. Therefore, the surface treatment before coating is also called coating surface pretreatment.

According to the welding specification, process test and process analysis, it is determined that the butt weld of Q345B square pipe adopts double-layer CO2 gas shielded welding. H08Mn2SiA, 2mm welding wire for welding material; The shielding gas is pure CO2 gas. The welding current of layer weld is 200 ~ 250A, and that of the second layer is 240 ~ 320A; The arc voltage is 24 ~ 26V. The process requirement is that the layer weld must be fully welded to ensure good back forming; The welding current, arc voltage, wire feeding speed and welding speed can be adjusted according to the equipment model.

The flattening speed of the sample can be 20 ~ 50mmin.

The modification of Ca, morphology and physical properties of inclusions in steel, spheroidize and refine inclusions in steel so as to improve the mechanical properties of square tubes.

how much.On the basis of thermodynamic calculation, rectangular tube,KhemiselKhechna50 galvanized square pipe size,KhemiselKhechnaGalvanized greenhouse square pipe, seamless square tube, galvanized square tube and galvanized tube is professional. New and old customers are welcome to consult during the preferential activities. The process conditions of calcium treatment of 20CrMo sulfur-containing square tube are analyzed, and the sulfur-containing gear rolled products after calcium treatment are sampled and studied. The conclusions are as follows: in order to minimize the generation of Cao in sulfur-containing square tube steel, Omega in molten steel; (O) It must be taken off to 10 & times; The rate of calcium can only be guaranteed below 10-6.

Square pipe for diamond core drilling (gb3423-8) is a square pipe for drill pipe, core rod and casing for diamond core drilling.

Steel with chromium content of more than 5% in steel and high corrosion of external medium (acid, alkali salt) is called square pipe. According to the condition in steel, square tubes can be divided into martensite, ferrite, austenite and ferrite & mdash; Austenite type, precipitation hardening square tube, according to the standard gb3280 & mdash; 92 regulations, a total of 55 regulations.

KhemiselKhechna.Empty bending is the bending moment formed in one direction between the outer roll and the outer wall of the tube blank to bend the strip. Empty bending will compress the bending line, the compression effect will lengthen the bending line longitudinally, and the metal at the bending will accumulate and thicken, which is the compression thickening effect of empty bending.

In fact, the casting cleaning is not just shot blasting. For large parts, the drum sand cleaning is carried out first, that is, the riser of the casting is cut off and rolled in the drum, and the square tubes collide with each other in the drum to remove most of the sand on the surface before shot blasting or shot blasting.

You can really feel that the square tube is widely used in the development, and q355b square tube factory continues to extend in the technical level, which makes the current square tube develop more widely.