Hot melt installation: pipes are connected according to the nature of thermoplastic coiled pipes. During hot melt, special heating equipment (generally electric heating type) is used to make the connecting surface of coiled pipes of the same material and pipe fittings reach the molten state, and they are pressed together manually or mechanically. This method is closely combined, safe and durable, and avoids water running, dripping and leakage at the joint of metal pipe fittings.
Flame cutting and plasma cutting are commonly used for sheet metal blanking in our factory. The equipment used includes manual cutting, copier, semi-automatic cutting machine and NC cutting machine. Manual blanking is arbitrarily large compared to other cuts Flexible and convenient, no special supporting cutting equipment is required.
.Purpose of steel plate rolling: steel plate rolling is mostly used in large-scale steel structure construction as the main support part, such as bridge piling, seabed piling and high-rise building piling. Its material: Q345C. Q345D and Q345E are also used in low temperature areas.
In addition, when the pipe rolling equipment is made, we should not have more than two longitudinal welds on the same cylinder section of the pipe rolling. For long-term pipe rolling, Q235B pipe rolling, Q345B pipe rolling, large-diameter thin-wall pipe rolling, large-diameter thick wall pipe rolling, stainless steel pipe rolling, L360 pipe rolling and 16Mn pipe rolling, the products are complete, the quality is excellent and the price is favorable. The distance between the two longitudinal welds should not be less than 200.
.In general, the hot coil pipe is mainly committed to the production of all kinds of circumferential seam and longitudinal ring coils and steel penstocks. It is reformed on the basis of traditional coil equipment and similar specifications and models, so that all parameters of the hot coil pipe can be improved, filling the gap that the original traditional coil equipment can not produce. In addition, in terms of processing technology, the hot coil pipe needs attention. The following matters are required: before processing, the hot coil pipe needs to be familiar with the technical requirements of paper, process material properties and other related aspects, select an appropriate hot coil machine, determine whether the cold coil, warm coil or hot coil, and then operate.
The products are widely used in petroleum, chemical industry, natural gas transportation, pile driving and urban water supply, heating, gas supply and other projects. The wall thickness of the hot-rolled thick wall coil of retailers generally exceeds 20mm, welded, formed, de reinforced, flaw detected and delivered under the state of steel plate heating. Sometimes the wall with special thickness needs secondary heating. It is characterized by small outer diameter tolerance and uniform wall thickness. The main thing is that the hot-rolled thick wall quality management coil will not damage the performance of raw materials. The disadvantages of hot-rolled thick wall coil are long processing time and the diameter of thick wall coil is generally above dn450.
The main materials are q23q3420, 435cimo and 42cimo, 16 manganese and 16 manganese capacity. Generally, cold rolled sheet can be used for pipe rolling, and the product standards are GB / t50205-200, GB / t3092-2001, etc. Continuous pipe is widely used in petroleum chemical industry, natural gas transmission, pile driving, urban water supply, heat supply, gas supply and other projects.
Round welded pipe joints shall be circular. The arc length of the coil calibration circle shall be 1 / 6 to 1 / of the circumference of the pipe, and the gap between the sample and the pipe shall comply with
The weld gap device is used to ensure that the weld gap meets the welding requirements, and the pipe diameter, misalignment and weld gap are strictly controlled.
Columns for bearing steel structures such as offshore platforms, super long-span building structures and electric pole tower and mast structures requiring wind resistance and earthquake resistance. Inspection equipment maintenance and packaging strategy: 16Mn thick wall coil adopts PLC automatic system, and all parts of Shenzhen thick wall coil focus on panel operation. The cutting length of 16Mn thick wall coil adopts photoelectric induction, accurate positioning and automatic cutting. Each working process adopts double pump oil pressure system, which runs smoothly, Shenzhen thick wall coiled pipe has good cutting synchronization performance. 16Mn thick wall coiled pipe has different application ranges: length: 0-1400mm, thickness: 2-15mm, application: 3 inches x2 4x, application voltage: 380V 50Hz. It is used according to the specified parameters and range to ensure that it can play an important role and value in use. The packaging process of new product 16Mn thick wall coil includes main processes such as filling, wrapping and sealing, as well as related pre and post processes, such as cleaning, stacking and disassembly. The process of 16Mn thick wall rolling pipe shall be strict, and it shall be produced in the correct way and principle. In addition, the process of 16Mn thick wall coiled pipe also includes measuring or stamping on the package. The use of mechanical packaging products can improve productivity, reduce labor intensity, meet the needs of large-scale production, d7z3xjb87v21w and meet the requirements of cleanliness and hygiene. The production process of rolling pipe is round pipe blank → Heating → Perforation & rarr; Roll cross rolling, continuous rolling or → Off pipe & rarr; Sizing (or reducing) → Cooling → Straightening & rarr; Hydrostatic test (or flaw detection) → Mark & rarr; According to different production, warehousing supply indicators can be divided into hot-rolled pipe, cold drawn pipe, pipe, etc. quality management? Hot rolled seamless tubes are produced on the automatic tube rolling mill. The solid tube blank is cut into the required length by removing the surface defects. The Shenzhen coiled tube is centered on the end face of the perforated end of the tube blank, and then sent to the heating furnace for heating. It is perforated on the piercing machine. At the same time, it rotates and advances continuously. Under the action of the roll and top head, a cavity called rough tube is gradually formed inside the tube blank, Then it is sent to the automatic pipe mill for continuous rolling, and the wall thickness is adjusted by the whole machine. The Shenzhen coiled pipe is sized by the sizing machine to meet the specification requirements. The production of hot-rolled seamless steel pipe by the continuous pipe mill is relatively advanced. If you want to obtain seamless pipe with smaller size and better quality, that is, the heated pipe blank is placed in a closed cylinder, and the perforated rod and rod move, Professional hot-rolled steel pipe, large-diameter thick wall rolling pipe thick wall straight seam rolling pipe, steel casing, rolling pipe factory has advanced technology, more affordable price and more preferential. Welcome to consult. Make the parts extruded from the smaller die hole. This method can produce the steel pipe with smaller diameter. Work course standard requirements & amp; amp; quot;Standard requirements: the Executive Standards of hot-rolled thick wall coil product line are: GB / t50205-200, GB / t3092-2001, etc.
Quality risk.The steel plate or strip is bent and then welded to form a thick wall coil. According to the welding form, it is divided into straight seam welded pipe and spiral welded pipe. According to the purpose, it is divided into ordinary welded pipe, galvanized welded pipe, oxygen blowing welded pipe, wire sleeve metric welded pipe, rolling pipe deep well pump pipe, automobile pipe, transformer pipe, welded thin-wall pipe, welded pipe and spiral welded pipe. Coil pipe is dedicated to the production of, longitudinal ring coil pipe and steel pressure pipe, and is modified according to similar specifications of traditional rolling equipment. The function of increasing the parameters of spiral steel pipe equipment by 30% fills the gap that the original traditional rolling equipment can not produce. It can produce steel pipes with a diameter of 400 or more and a wall thickness of 8-100mm. The material mainly includes Q235, Q345, 20, 16 manganese, 16 manganese capacity, etc. Product executive standards include: GB / t50205-2001, GB / t3092-2001, etc. The products are widely used in petroleum, chemicals, natural gas transportation, pile driving, urban water supply, heating, gas supply and other projects. When the coiled pipe is greater than 600mm, two longitudinal welds are allowed, and the spacing shall be greater than 200mm.
During pipe rolling, the surface damage of steel plate shall be prevented. The parts with serious scratches must be polished for transition, and the wall thickness of the polished parts shall not be less than the design wall thickness.
Let me introduce the standard coil produced by steel plate. In the process of rolling, the surface of the circuit board should be protected from damage. Parts with severe scars shall be ground to achieve transition, and the wall thickness of the ground part shall not be less than the design wall thickness.
Extend the length of the part: 566, divide it into 24 equal parts symmetrical, and the length of each bisector from the middle to the side is: 11 110 106 10 93 84 75 66 57 0 50 44 40 39 2.
discount.The rolling pipe factory mainly produces steel plate rolling pipe and thick wall rolling pipe. With the development of domestic economic situation and the acceleration of welding and casting trend, but also improves the working environment and labor efficiency. At present the advantage of NC cutting is gradually recognized. NC cutting not only greatly improves the rate of plate and product quality, the CNC cutting machines used in the thick wall rolling pipe processing industry are mainly flame and ordinary plasma cutting machines, but pure flame cutting can not meet the needs of modern production, At present, most CNC cutting machines are CNC plasma cutting machines. This type of cutting machine can meet the needs of thick wall coiled pipe plate processing and thick wall coiled pipe parts processing, so the demand will be greater and greater, but there is still a very obvious gap with foreign countries, mainly in
Meet the requirements of American Petroleum Institute standards.
The function of parameters of pipe rolling equipment is improved by 30% which fills the gap that can not be produced by traditional steel rolling equipment. It can produce steel pipes with diameter of more than 400 and wall thickness of 4-100mm. The main materials are q23q3420, cold-rolled sheet can be used for pipe rolling. Product standards: GB / t50205-200, GB / t3092-2001, etc.
.Chinese Name: welded pipe English Name: welded tube, and welding the joint with appropriate welding. Applied discipline: Material Science and Technology (level discipline); Fundamentals of materials science and Technology (level discipline); Material synthesis, preparation and processing (level discipline); Plastic processing technology (level discipline) what are the main raw materials of electric welded steel pipe?
1800mm steel pipe elbow detailed introduction to elbow: first of all, the material is hot pushed, the pusher is a horn shaped core or mandrel, the mandrel is thickened and thickened, the process of pushing the elbow is the process of expanding the diameter, and it is supported on the back. The material tube part passes through the mandrel, and there is an arched frame at the rear to fix the mandrel. There's a car in the middle. Some cars are driven hydraulically, others are driven by mechanical transmission, that is, screw drive, and then the car pushes forward, and the car pushes the pipeline along the core. The rod moves forward, there is an induction coil outside the mandrel, the tube is heated and heated, and then the trolley pushes the tube down and processes one.
With the development of domestic economic situation and the acceleration of welding and casting trend, the advantages of NC cutting are gradually recognized. It has long provided various brand products such as hot-rolled steel pipe, large-diameter thick wall rolling pipe, thick wall straight seam rolling pipe, steel casing and rolling pipe factory. The designated products are complete and the quality is guaranteed. NC cutting not only greatly improves the rate of plate and product quality, but also improves the working environment and labor efficiency. At present, the NC cutting machines used in the thick wall coil processing industry are mainly flame and ordinary plasma cutting machines, but pure flame cutting can not meet the needs of modern production. At present, most NC cutting machines are NC plasma cutting machines. This type of cutting machine can meet the needs of thick wall coiled pipe plate processing and thick wall coiled pipe parts processing, so the demand will be greater and greater, but there is still a very obvious gap with foreign countries which is mainly reflected in: 90% of the developed thick wall coiled pipe processing industry is digital control cutting machine, and only 10% is manual cutting; The CNC cutting machine only accounts for part of the total blanking. 10%, of which the proportion of NC plasma cutting is small. In industrial production, plasma cutting, laser cutting and so on. Among them, plasma cutting has a wider cutting range than gas cutting More efficient. Fine plasma cutting technology is close to laser cutting in material cutting surface quality, but the cost is much lower than laser cutting. Therefore since the successful development of the United States in the mid-1950s, plasma cutting has developed rapidly. With the rapid development of computer and digital technology, NC cutting is also developing, which improves the machining accuracy. It shows great advantages in saving materials and improving labor productivity. This leads to the development of plasma cutting technology from manual or semi-automatic to NC, which has become one of the main directions of NC cutting technology. NC plasma cutting technology is a set of high-tech technologies such as NC technology, plasma cutting technology and inverter power supply technology. Its development is based on the common progress of computer, plasma arc characteristic research, power electronics and other disciplines. The CNC cutting technology began in the 1980s, and the CNC plasma cutting technology was later. However, recently, some domestic universities, research institutes and manufacturers have studied NC plasma cutting technology and gradually developed and produced various specifications of NC plasma cutting equipment, narrowing the gap of foreign advanced technology.