HDPE plastic square pipe made according to the properties of square pipe has the advantages of light texture, high strength, good resistance, easy laying, low water resistance, low cost and corrosion resistance. Its service performance and economic benefits far exceed reinforced concrete pipe and general specification iron pipe. It is an updated product of engineering pipe.
Elongation after square tube breaking (& sigma;): in the tensile test, the percentage of the length increased by the gauge length of the sample after breaking and the length of the original gauge length is called elongation. In & sigma; Expressed in%.
Anchorage.Principle of cold drawing strengthening: the lattice defects of steel increase during plastic deformation, and the serious distortion of defect lattice will hinder the progress and slip of lattice, so the yield point of steel increases and the plasticity and toughness decrease. Due to the internal stress in plastic deformation, the modulus of steel decreases. The cold drawn reinforcement is stored at room temperature for 15 ~ 20d or heated to 100 ~ 200 ℃ and maintained for a fixed time. This process is called aging treatment.
Square tube is in our reality
.Square pipe also known as square and rectangular cold-formed hollow section steel, is referred to as square pipe and rectangular pipe for short. The allowable deviation of wall thickness of square pipe is f and J q355b respectively. When the wall thickness is no more than 10mm, it shall not exceed plus or minus 10% of the nominal wall thickness. Long term square pipe, rectangular pipe, seamless square pipe galvanized square pipe, galvanized pipe, 20-year-old brand, price advantage and quality guarantee! When the wall thickness is greater than 10mm, it is plus or minus 8% of the wall thickness, except for the wall thickness of corners and weld areas.
Great relationship. Large fillet radius insufficient blank holder area, and the material is not easy to move and transfer inward the resistance of the material into the die will increase in the deformation process thus increasing the large tensile stress in the force transfer area, which may lead to tensile cracking.
Square pipe, the square tubes produced by q355b square tube factory are mainly used in tap water engineering, petrochemical industry, chemical industry, electric power industry, agricultural irrigation and urban construction. For transportation: water supply and drainage. For gas transmission: gas, steam and liquefied petroleum gas. do
Great relationship. Large fillet radius, easy to produce unstable wrinkles; If the fillet is too small, the resistance of the material into the die will increase in the deformation process, and the material is not easy to move and transfer inward, thus increasing the large tensile stress in the force transfer area, which may lead to tensile cracking.
B. converter steel: (a) acid converter steel; (b) Basic converter steel. Or (a) bottom blown converter steel; (b) Side blown converter steel; (c) Top blown converter steel.
Drawing process flow of square tube in the production process of square tube, it needs a lot of processes to complete the production process, so that the production quality of square tube can be more strictly guaranteed. This paper mainly introduces the drawing process flow of square tube. Let's understand it below.
Executive standard.The test can be carried out under cold and hot conditions. If the test temperature is not specified, the test shall be carried out under normal temperature, but not lower than - 10 ℃.
Section shape classification square tube is classified according to section shape: simple section square tube: square tube, whether shot blasting or sand blasting, compressed air is used. Professional square pipe, square rectangular pipe, seamless square pipe, galvanized square pipe, galvanized pipe has high pressure resistance grade, good waterproof performance, fire and high temperature resistance, strong overload capacity, corrosion resistance, radiation protection and long service life. Of course, it is not shot blasting, so it is necessary to use high-speed rotating impeller. In the repair and shipbuilding industry, shot blasting (small steel shot) is mostly used in square pipe pretreatment (rust removal before coating); Sand blasting (mineral sand is used in repair and shipbuilding) is mostly used in formed ships or sections to remove the old paint and rust on the square tube and repaint it. In the repair and shipbuilding industry, the main function of shot blasting and sand blasting is to increase the adhesion of square tube coating paint.
The surface compressive stress characteristics of the square tube will be obtained after isothermal quenching.
technological innovation.Therefore, the plasticity and quality of q355b square tube forged are relatively good, so general manufacturers will forge q355b square tube, professional square tube, seamless square tube, galvanized square tube, galvanized tube to ensure quality, service and quality. Your satisfaction is our pursuit! Welcome to inquire. So now there are many applications of q355b square tube.
After spraying (throwing) derusting, it can not only expand the physical adsorption on the pipe surface, but also enhance the mechanical adhesion between the layer and the pipe surface. Therefore, spray (throwing) derusting is an ideal derusting method for pipelines. Generally speaking, shot blasting (sand) is mainly used for the inner surface treatment of the pipe, and shot blasting (sand) is mainly used for the outer surface treatment of the pipe. Several problems should be paid attention to in derusting by spraying (throwing).
Hot rolled q355b square tube continuous casting slab or blooming slab is used as raw material, heated by stepping heating furnace and descaled by high-pressure water into roughing mill. Roughing material enters finishing mill after head cutting tail cutting and then computer rolling. After final rolling, it is rolled into straight hair coil through laminar cooling and coiler. The head and tail of straight hair curl are often tongue shaped and fish tail shaped, with poor accuracy of thickness and width, and there are often defects such as wave shape, hem, tower shape and so on. The coil weight is heavy and the inner diameter of the steel coil is 690mm.
Anchorage.Application of square tube products: for mechanical equipment, steel structure, automobile parts, bridge ground pile, guardrail and ship internal structure.
The normal process flow is as follows: the round steel is perforated to form a tube embryo, then pickling is carried out, the black skin on the outer surface is washed off, and then grinding is carried out. After passing the inspection, the rolling mill or cold drawing and cold drawing are carried out. Annealing is required for wall reduction, but not for air drawing. After forming, annealing and straightening are carried out, and pickling is tested and stored in the warehouse. Basically, these are the processes. Better manufacturers will perform whitening treatment during annealing to make the surface treatment more beautiful. The narrow blank of square pipe can produce welded pipe with larger diameter, and the blank of the same width can also produce welded pipe with different diameter. However, compared with the straight seam square pipe with the same length, the weld length increases by 60%, and the production speed is low. Square pipes with large or thick diameter are usually made of steel blank directly, while small welded pipes and thin-walled welded pipes only need to be directly welded with steel strip. Then after simple polishing, wire drawing is OK. Therefore, straight seam welding is mostly used for relatively welded pipes, and spiral welding is mostly used for large-diameter welded pipes.
The standard quantity of combustible and nonflammable square pipes is gbt97-1 (gbt97-199). The representative material is l245-l4 pipeline steel. Professional square pipes, square rectangular pipes, seamless square pipes, galvanized square pipes and galvanized pipes are of high quality and low price. They are fire-resistant, waterproof, high temperature resistant, durable, safe and reliable. They are mainly used to transport combustible and nonflammable fluids with high requirements.