Now stainless steel is gradually replacing pure iron products in our life, and now the steel pipe is also gradually innovated. Now the q355b square pipe is a typical representative. However, the above small series are not the focus. Today, and the morphology of sulfide in the rolled stock is also improved.
Aserri.Steel pipe for geological drilling (yb235-7) is a steel pipe used by geological departments for core drilling. It can be divided into drill pipe, drill collar, core pipe, casing, sedimentation pipe, etc.
With the progress of the times, square tubes are used in more and more fields, and their scope of use is obviously increasing, which makes us have many kinds of square tubes. At this time, we need to store square tubes reasonably. Customers should also learn to arrange reasonably when storing square tubes. Let's understand how to store square tubes correctly.
.The square tube represents the large capacity of the metal material under the action of tension, and the calculation formula is: where: FB -- the strong force borne by the sample when it is broken, n (Newton); So -- original cross-sectional area of sample, which is called the yield point.
Compared with other traditional pipes, square pipe supply steel pipe has lighter raw materials, high strength, good resistance, can withstand high internal pressure, sensitive application, and can get used to messy or bad geological conditions.
It is mainly caused by the fact that the square pipe body has no cover, the covering protection is not ideal, partly due to the excessive number of stacking layers, and most coastal areas belong to marine climate, with large annual rainfall, high air humidity, ponding in the square pipe and the square pipe. The protection shall be: if the bare pipe or pipe needs to be stored for a long time, it shall be protected with an uncovered object from the beginning of storage to avoid rusting, layer aging, edge warping and other phenomena of the square pipe.
Banded due to improper hot working temperature, that is, when the hot working stop forging temperature is in the phase zone (between, and 40), ferrite precipitates in bands from austenite along the metal flow direction, and the undigested austenite is cut into bands. When it is cooled to a, the banded austenite is transformed into banded pearlite. This can be improved or eliminated by increasing the final rolling temperature, increasing the forging ratio, diffusion annealing and normalizing.
The second is to clean the surface of the opposite pipe. When cleaning the opposite pipe, the surface should be cleaned with solvent or emulsion. Square pipes of various specifications, seamless square pipes, galvanized square pipes, galvanized pipes are supplied in time and cost-effective. They have become the preferred brand of many wire products. Welcome to buy! It is used to remove oil and dust. It is only suitable for removing grease and dust on the surface of square pipe, which can not remove rust and oxide scale. Therefore, it can only be used as an auxiliary means in production.
Square pipe, the steel pipe whose ratio of outer diameter to wall thickness is less than 20 is called square pipe. At present, the square tubes produced by q355b square tube factory are mainly used in tap water engineering, petrochemical industry, chemical industry, electric power industry, agricultural irrigation and urban construction. For transportation: water supply and drainage. For gas transmission: gas, steam and liquefied petroleum gas. do
Good reputation.Before gas cutting, remove the dirt and grease on the steel surface, and leave a certain space below to facilitate the blowing out of slag. During gas cutting, the movement of the cutting torch shall be kept at a uniform speed. The cutting surface should be 2 ~ 5mm away from the tip of the flame core. If the distance is too close, the edge of the cut will melt, and if it is too far away, the cutting will be interrupted easily due to insufficient heat.
The great difference between the square pipe and the thin-walled steel pipe produced by the square pipe factory lies in the thickness of the steel pipe wall. Generally speaking, the thin-walled steel pipe is cold drawn technology while the square pipe generally uses hot rolling technology. If it is distinguished by the unit of measurement, it is generally believed that the watershed between the square pipe and the thin-walled steel pipe is that the wall thickness diameter is equal to 0.02, and the thin-walled steel pipe is that the wall thickness diameter is less than 0.02, Larger than is the square pipe. In terms of use, thin-walled steel pipes are mostly used in pipes. The square tube is mostly used in the blank of hollow parts. Used on pressure bearing and important pipelines.
Large diameter welded square pipe for low pressure fluid transmission, Standard No.: gbt14980-1994. Representative material: grade q235ab. It is mainly used to transport low-pressure fluids such as water sewage, gas air and heating steam.
Two main factors should be considered in the design of square pipe section: one is the safety of the section; the other is the economy of the section. For the safety of the section, we require that the ratio of waist thickness to height of H-section steel should not be less than 145. For H-section steel used as column its economy is expressed by the ratio of torsion radius to its mass.
Marketing Department.The modification of Ca, rare earth and other trace elements on inclusions changes the structure, morphology and physical properties of inclusions in steel, so as to improve the mechanical properties of square tubes.
Steel for construction and engineering according to the classification of use without phase transformation or partial phase transformation of square tube: A. ordinary carbon structural steel; b. Low alloy structural steel; c. Steel reinforcement.
The standard number of spiral square pipe (standard of the Ministry of petroleum) for low pressure transmission is syt5037-2008. The representative materials are q235bq345b and other carbon steel materials. It is mainly used for low-pressure transmission of water, oil, natural gas, heating and other pipelines.
Aserri.The strength, plasticity and angle discussed later are the machine function indicators of metal under static load. In practice, many mechanical machines are under repeated load and the whole opportunity is tired in this environment.
Stainless steel q355b square pipe for mechanical structure, Standard No.: gbt12770-1991. Representative materials 0Cr 1cr1 00cr19ni 1Cr18Ni 0cr18ni11nb, etc. are mainly used for mechanical parts and structural parts such as machinery, automobile, bicycle, furniture, hotel and restaurant decoration.
Tensile strength: 490-675 yield strength: & Ge; 345 elongation: & Ge; 22 mechanical properties of seamless pipe: tensile strength: 490-675 yield strength: ≥ 345 elongation: & Ge; 21 mechanical properties of seamless pipe: tensile strength: 490-675 yield strength: ≥ 345 elongation: & Ge; 21 mechanical properties of seamless pipe: tensile strength: 490-675 yield strength: ≥ 345 elongation: & Ge; 22 mechanical properties of seamless pipe: tensile strength: 490-675 yield strength: ≥ 345 elongation: & Ge; 22 square tube belongs to low alloy series. It is one of the materials of seamless steel pipe. In low alloy materials, this material is ordinary. Square tube used to be called Q345B square tube.