SofiaGuide raiSecondly there should be no dirt on the friction surface. If there is any dirt, it should be washed off with gasoline or thinner; The reduction gearbox, gearbox, external meshing gear, and other parts of the equipment, as well as the hydraulic oil, must be tested according to the requirements in the table; Correct maintenance of the hydraulic guide rail elevator: Regularly inspect the wire ropes at various parts for broken wires and looseness. If any such phenomenon is found, replace it in a timely manner. The maintenance of the wire ropes must be carried out in strict accordance with the specifications; Check the connection condition of each part according to the braking rules and regulations. If there is any looseness, whether there are noises and faults according to regulations, and promptly remove all faults; When installing, disassembling, and adjusting the rotating mechanism of the equipment, and the meshing clearance should be appropriate; Regularly conduct a comprehensive inspection of the equipment to see if there is any damage to the wires and cables, boxes, distribution boxes, and brushes of the motor are kept clean, and that the travel switch points of each safety device must be safe and reliable.
Frequently check for water accumulation and humidity. It is inevitable for aerial vehicles to drive in rainy and snowy weather, or muddy roads. The bottom and some gaps and indoor floors are prone to sludge accumulation. If the owner does not clean them in a timely manner, this can cause moisture to hide. Therefore,SofiaFive ton cargo elevator, activities in the outer edges of wheel hubs, doors bottom corners of tree trunks, key holes, and wiper brackets, as well as other areas, should be regularly inspected, and the drainage holes in the doors and various parts should be kept unblocked to ensure that the car seat covers, such as humidity, carpets, and floors, prevent rust from forming parts.
Sofia.The one-way valve is damaged. The one-way valve is designed to prevent oil return. If there is a problem, there will be some backflow, so it can be replaced at this time.
Characteristics of hydraulic elevators: Hydraulic lifting platform products are divided into curved arm type hydraulic lifting machines, scissors type hydraulic lifting machines, mast type hydraulic lifts, and straight arm type hydraulic lifts according to their working modes. Hydraulic elevator is a replacement product of folding arm elevator (lifting platform) and scissor fork elevator (lifting platform). It can be widely used for the decoration and decoration of stations, docks airports, hotels, posts and telecommunications, municipal gardens, cleaning companies, public building facades, or the installation and maintenance of power systems, etc. This elevator has the advantages of light weight, self-propelled walking, electric starting, self supporting legs, simple operation, large working area, and especially the ability to cross obstacles for aerial work.
.Hydraulic lifting platforms are widely used in factory maintenance, municipal construction, and decoration of hotels in industrial and mining enterprises, with reliable quality and perfect performance.
Incorrect connection of the elevator motor When a coil, coil group, or one phase winding group is connected inversely, it can cause a serious imbalance in the three-phase current and cause the winding to overheat.
Corrosion prevention measures for the body of aerial work vehicles Attention to small scratches The paint surface of aerial work vehicles often corrodes. In addition to common collisions, scratches, and small rocks on the drive tire, there can also be a paint peeling point that can cause a small rust over time. Because most of these scars are small and easy to ignore. Therefore, regularly inspect the engine compartment lid and surrounding areas, and once found, go to a professional beauty shop for processing in a timely manner.
The hydraulic lifting platform can be divided into four wheeled mobile type, two wheeled traction type vehicle modified type, vehicle type, auxiliary self-propelled type, and the lifting height varies from a meter to 1 meter.
In fact, it is also important to pay attention to some details, as follows: It is actually difficult to pierce the bearings into the shaft pins when excessively installing them. However, sometimes, some people think of using a hammer to hammer the bearings to facilitate the installation, and use brute force during installation. In fact, directly striking the bearings with a hammer can cause significant damage to the bearings, which is the main reason for causing bearing damage and reducing the service life of the bearings. So when installing bearings, we must not go too far. Fortunately, we can place some soft cloth or cardboard on top of them before installing them.
Guide rail elevator (also known as cargo elevator) is a non scissor fork type hydraulic lifting platform, mainly used in industrial buildings, restaurants, restaurants, warehouses, docks, workshops, and other places where vertical cargo handling is required between two or more floors. The low height is particularly suitable for sites that are not suitable for digging pits on site. What issues should we pay attention to in these places where elevators are used?
Test conclusion.Is the water cooling and air cooling of the hydraulic station the same?
Prepare the foundation according to the foundation plan, pay attention to alignment, leveling, and alignment, and ensure the level of the foundation and various usage requirements.
Systems: explosion-proof electronic control system remote control system,SofiaTwo story cargo elevator, PIC system.
For guideway elevators installed outdoors, they are often exposed to rain and sunlight so special attention should be paid to regular maintenance and inspection to avoid accidents.
Product range.Incorrect connection of the elevator motor When a coil, or one phase winding group is connected inversely, it can cause a serious imbalance in the three-phase current and cause the winding to overheat.
The main structure and use of the guide rail type elevator are closed gear transmission, and the large and small gears are made of steel. After quenching and tempering treatment, they belong to the soft tooth surface. As the common failure form of closed soft tooth surface gear transmission is tooth surface pitting, the design is based on the tooth surface fatigue strength and checked based on the tooth root bending fatigue strength. The bracket bracket is used to fix and support all mechanical parts and some electrical components of the elevator chassis. It is mainly welded from parts such as side plates, connecting tubes, and connecting pieces. The materials are all selected, including the thickness of both sides of the plate, products, and tens of millions of products. Professional elevator factory transactions are safe and guaranteed. At the same time, in order to reduce the weight of the bracket, many process holes are designed on both sides of the plate. The worm gear and worm mechanism has the advantages of large transmission ratio, compact structure, small impact load, stable transmission, low noise, and has the characteristics of reverse self-locking. It can ensure that the transmission mechanism can self-lock when the motor is powered off during patient handling, so a worm gear reducer is selected. The involute worm is used and the material is steel. Its spiral surface is quenched to improve transmission efficiency and increase wear resistance. The worm gear is made of polyformaldehyde. Plastic worm wheels have the advantages of good processing economy, stable transmission, vibration absorption and noise reduction, light weight, and self reliance, making the design of the elevator more humanized.
For guideway elevators installed outdoors, they are often exposed to rain and sunlight, so special attention should be paid to regular maintenance and inspection to avoid accidents.
Sofia.Many people believe that the mechanical strength of the elevator itself is relatively high when using the elevator, so the installation method specified in the manual is not strictly followed during the installation process. However, this can lead to increased wear of parts and inflexibility in operation. In addition, it is necessary to pay attention to the installation precautions corresponding to the working environment and not be careless. Correct installation, use, when installing the elevator, please be sure to carefully assemble and use it in strict accordance with the following installation and use related matters.
Precautions for elevator installation: Keep the access road of external construction elevators smooth and have sufficient space for parking equipment. When using a steam crane for auxiliary installation, full consideration should be given to whether the on-site environment meets the operating conditions of the steam crane.
Knowledge popularization and superior performance of scissor fork type fixed lifting platform: equipped with safety devices to prevent overloading of the lifting platform; Equipped with a protection valve to prevent hydraulic oil pipe from cracking; Equipped with an emergency lowering device for sudden power failure; The doors of the upper and lower floors are equipped with safety devices that interlock with the system.