GorontaloCopper plateProduct classification related knowledge

Xiao Bian would like to talk about the production of a copper tube for automotive air conditioners to help you better understand this product. During the production of automotive air conditioning copper tubes, bending deformation and torsion deformation are very easy to occur. Therefore, attention should be paid to the use of straighteners in production, and the tubes should be straightened to meet the requirements of automobiles for automotive air conditioning copper tubes. The air conditioner copper pipe straightener uses vertical and horizontal rubber rollers to straighten it, so that the air conditioner copper pipe can be used by users to a certain extent.Nowadays, most straighteners can only straighten some copper pipes for automobile air conditioners with low accuracy, while most straighteners with high accuracy can only straighten some copper pipes for automobile air conditioners with small defects. Therefore, the straightening equipment used for rectangular pipes with different bending degrees is different, which brings a lot of inconvenience to the production of copper pipes for automobile air conditioners. Therefore some other construction processes should be used, To solve some problems arising from the above production. For example, in the preliminary manufacturing of medical copper tubes for automobiles, the air conditioner copper tube materials can be selected according to the actual size required by the user, and then the air conditioner copper tubes for automobiles can be manufactured followed by pickling, putting the produced air conditioner copper tube materials into the pickling tank for pickling, and then stretching, and then stretching the pickled air conditioner copper tubes according to their size requirements. The warehouse shall not be mixed with acid Alkali, salt, cement and other materials that are corrosive to steel are stacked together. Air conditioning copper pipe is based on carbon structural steel. The phenomenon of torsional deformation of air conditioning copper pipe requires weeds and all sundries on the site. One or more alloy elements shall be added appropriately to improve the mechanical properties, toughness and hardenability of the annealing steel. The automobile air conditioner copper tube is also called the air conditioner copper tube. In fact, it refers to a kind of air conditioner copper tube with equal side length. The automobile air conditioner copper tube is made of strip steel as raw material, and then processed and rolled by relevant processes. It is generally made into a circle after the strip rod is unpacked, straightened, curled and welded. Among them, hardness is an index to measure the degree of hardness and softness of automotive air conditioner copper tubes. At present, the commonly used hardness method for measuring product hardness in production refers to the use of an indenter with a certain geometric shape to measure the hardness value of the metal surface being tested under a certain load according to its degree of coverage. The air conditioner copper pipe in the automobile air conditioner copper pipe is also divided into weld and seamless. Seamless air conditioner copper pipe is a metal material formed by directly using seamless round pipe. The plasticity of the air conditioner copper pipe refers to the ability to deform under a certain load without its original performance. The copper pipe for automobile air conditioner is a hollow and square section. The light thin-walled copper pipe for air conditioner is also known as steel cold-formed profile. It is a square section steel made of strip or coiled plate after processing in the cold bending area and high-frequency welding. In addition to being used in the automobile industry, the air conditioning copper pipes are used in construction, machinery manufacturing, steel construction and other projects, shipbuilding, solar power generation support, steel structure engineering, electric power engineering, power plants, glass curtain walls, boiler construction, highway railings, housing construction, pressure vessels, oil tanks, bridges, power station equipment, lifting and transportation machinery and other high load welding structures. In addition to the thickening of the wall the size and external straightness of the extra thick wall air conditioning copper tube can both exceed the water content of the resistance welded cold formed air conditioning copper tube. Therefore, this kind of automobile air conditioning copper tube has better comprehensive mechanical properties and has the advantages of hot processing, cold processing weldability and corrosion resistance.

The demand for t2 copper tubes is increasing. At the same time, the quality identification method of t2 copper tube for grid fittings is currently accompanied by rapid economic development. There are many kinds of sales in the market, different types, different purposes, and different quality. Therefore, when purchasing, you should be clear and have certain selection skills. Here we introduce the quality identification method of t2 copper tube. The color of t2 copper tube depends on the color of t2 copper tube. Although the external color is a visible factor, the color of the product is closely related to its production process and quality control. If the product is bright in color and high in glossiness, it is generally superior to the product with poor color. The t2 copper tube with uniform thickness should be selected. Because some small manufacturers are limited in technology and process, the thickness is also an important factor to test the quality of the pattern plate. Later, the casting process of t2 copper tube.

Gorontalo.The main force of iron ore futures closed at 428 in 180 The closing price of the day today was the same as that of the previous trading day, including * * * * 433 * * * 425, settlement price 426, trading volume 2071056, and position volume 18599. The intraday trading volume decreased by 200000 compared with the previous trading day, and the position volume decreased by 50000 compared with the previous trading day. After six consecutive days of downward adjustment, there was a rebound at the bottom of the session today, but it was corrected again later, and the closing was flat.

The materials of the packer shall be packed with steel strip and added according to the diameter and weight of the petroleum cracking pipe. The degreased copper pipe from the pipe can be packed without a packer. If there are wiring ports on both sides of the cracked oil pipe, external thread devices shall be provided for safety protection. Brush the nozzle with clean oil or anti rust oil. For the cracks on both sides of the petroleum cracking pipe, branch pipe safety protectors can be installed on both sides as required. If the oil cracking pipe is installed in the container, the container shall be lined with waterproof devices such as woven cloth and straw mats. In order to better distribute the textile petroleum cracking tubes in the tank, the wound is uneven and cracked. Then I will introduce how to solve these problems. For the disconnection part of plastic coated copper pipe the packer can weld the safety protection support frame inside the petroleum cracking tubes. Previous page: How to clean plastic coated copper tubes. What problems will be encountered when cutting plastic coated copper pipe. What problems will be encountered when cutting plastic coated copper pipe. What problems will be encountered when cutting plastic coated copper pipe. When plastic coated copper pipe is cut, the position and direction shall be drawn with tape or other measuring tools and the disconnection line shall be marked in combination with the construction drawing and site conditions. When the petroleum cracking pipe is disconnected, please fix the equipment with square steel pipes such as vises, and cut it after fixing. In the area to be disconnected, use a towel or soft cloth to crack the oil stain or dirt on the surface of the pipe. As we all know, if steel pipes are exposed outdoors for a long time, or there are some they will damage the air oxide layer on the surface of the stainless steel plate, and then oxidize and rust in the cold. Gas. Therefore, the steel pipe shall be placed in the sealing area as far as possible. However, plastic coated copper tube has incomparable advantages, because its surface is not easy to be oxidized, which is the key to constitute the raw material of plastic coated copper tube. The high-precision plastic coated copper pipe has an extremely thin, firm and smooth chromium rich air oxide film on its surface to prevent oxygen molecules from re penetrating and re oxidizing in the air, thus preventing rust. The description of the plastic coated copper pipe shows that the part with weak corrosion resistance of the transition film will produce pitting corrosion reaction due to the self-excited reaction, and the small holes will form highly corrosive aqueous solution. The chloride ion content will accelerate the corrosion rate.

.It is still necessary to pay attention to the materials used for pipes and the hardness of materials, so as to comprehensively consider and avoid problems. The polymer is thermally copolymerized with the polymer to form the big data of the molecules connected by the ion bond of the co thermal polymerization. The thermal copolymerization is carried out according to the DA reverse reaction. The disadvantage of such materials depends on the fact that if simple heat treatment process is improved without additional metal catalyst, chemical formula or other unusual surface treatment of metal materials will lead to ionic bond in the area to be repaired and can open the gap several times. Copper tube concrete based textile materials. Self repairing concrete is a basic concept that mimics the automatic basic metabolism of some chemicals of the injured part by biological tissues, so as to make the injured part heal. Hollow glass fiber or liquid core optical fiber may damage the hollow bag of concrete raw materials, damage the hollow glass fiber or liquid core optical fiber, and flow the adhesive to the damaged part, whether it is processed or stored in the warehouse.

Now let me talk about the damages that are easy to occur on the surface of the copper tube. In order to prevent the accumulation of process agents or products and/or dirt, scratches and other rough surfaces, mechanical cleaning must be carried out. If the copper pipe is heated to a certain high temperature in the air during welding or grinding, chromium oxide heat return color will appear on both sides, lower surface and bottom of the weld. The color after tempering is thinner than that of the oxidation protective film, and is clearly visible. The color depends on the thickness. The thicker oxide can be found in the rainbow color, blue, purple to brown. It is usually black. It is caused by being at high temperature or being at high temperature for a long time. When any of these oxide layers exist, the chromium content on the metal surface will, and the corrosion resistance of these areas will. In this case, it is not only necessary to heat temper the color and other oxide layers, but also to clean the chromium poor metal layer under it. Free iron on the surface of t2 copper tube will rust, causing corrosion of stainless steel. Therefore, the powder that must float can usually be removed together with the dust. Some are very sticky and must be treated as embedded iron. In addition to dust, there are many surface iron sources, including cleaning with ordinary carbon steel wire brush and shot peening with sand,GorontaloBronze tube, glass beads or other abrasives previously used on ordinary carbon steel low alloy steel or cast iron, or regrinding non stainless steel products attached to copper pipe components and equipment. If there is no protection during cutting or hoisting, the wire ropes, slings and iron on the working surface can easily be embedded or dirty the surface. The copper tube shall be boiled in boiling water for 30 seconds before cold treatment. The effective internal stress is about 15%, and the residual austenite reaches the effect. Then, the cold treatment can be carried out as usual. Of course, the second suggestion is to choose the normal treatment at minus 60 degrees, and then conduct deep cooling at minus 120 degrees. The lower the treatment temperature is, the retained austenite will be rapidly transformed into martensite, but it cannot be transformed. Through experiments, it can be found that there will be about 2% of retained austenite. At this time, retained retained austenite can achieve a certain buffer effect. After cold treatment, which can effectively heat about 40% of the cold treatment stress. Tempering and cold treatment should be carried out as soon as possible after gradual heating, and most of them can avoid cracks as soon as possible so as to ensure that the products will not deform in later use and facilitate daily storage. The transformation characteristics of the area of each layer of the copper tube during empty drawing affect the asymmetry of the deformation of the metal material. One of its characteristics is that the natural widening of each layer along the wall thickness is not consistent. Of course, the external layer of the copper tube is less, the internal surface layer of the copper tube is larger, and the natural widening of the middle layers is slow from the external layer to the internal surface layer.The technical level of degreasing copper tube for mechanical equipment With the substantial improvement of the manufacturing level of mechanical equipment and the degree of control automation in China, there is still some gap between the technical level of domestic degreasing copper tube production line and the products of foreign counterparts. After years of reform and opening up. The quality of all aspects of degreased copper pipe has also risen by several grades, can provide stable and reliable production equipment for domestic and international markets, and make great contributions to the aluminum packaging industry. With the continuous improvement of people's living standards, there will be more and more demand for degreased copper tube products, and its market potential is huge. Problems such as incomplete penetration, deformation, cracks and air holes are easy to occur during the fusion welding of degreased copper tubes. Compared with fusion welding, wood is not melted during brazing, which reduces the impact of large thermal conductivity of base metal on welding quality, prevents the formation of incomplete penetration, reduces the tendency to produce pores and cracks, and ensures the performance of weld. Because the base metal is not melted, the structure and properties of the base metal are almost unchanged, alkali, salt, cement and other materials that are corrosive to steel. The air conditioning copper pipe is based on carbon structural steel. The phenomenon of torsional deformation of the air conditioning copper pipe requires weeds and all sundries on the site. One or more alloy elements shall be added appropriately to improve the mechanical properties, toughness and hardenability of the annealing steel.

The price can be changed, and the transaction is affected. According to the feedback from the spot operation, the morning market transaction did not follow the temperature rise: after 9:00, the dealers took turns to raise the price, which was in disorder; Before ten o'clock, it was not as expected, the surrounding markets became loose and the price was low. High hanging, low selling, which is different from the opening. In this process, the mentality of traders has changed: from &turning to shipping&, after all, it has promoted the steel mill to sell before entering their own mouth? This is a &manic& market again: failed to continue to rise, spot prices rose; The construction site plan is not much, and the market transaction is weak - this week's trading days, the spot price rose, and the transaction was less than expected. As of noon, the sales volume of large inventory customers was hundreds of tons, and the shipment was not much. Judging from the transaction in the morning, the base price of t2 copper tube was 5050 yuan/ton, and the price of earthquake resistant spiral snail was 5350 yuan; Among the resources provided by the factory, the basic price of threads of Zhongtian, Yonggang and Shagang is 5130 yuan, and the differential between spiral and t2 copper pipes is 360-380 yuan/ton. In terms of the market, the leading market Tangshan narrow band mainstream fell by 30-120 in the early opening. The overall trading situation of copper bars was weak. Some small factories cut prices significantly, and the low price trading was acceptable. Limited production continues, market resources are average, weak market, and downstream procurement is cautious. 355 is the consolidation of the medium broadband market. Today's futures continue to fluctuate. Traders are less willing to ship at low prices and have a strong mood. However, under the pressure of futures, the trading atmosphere in the spot market is not good. Copper bars continued to fluctuate in the morning, and traders were affected by multiple factors to make a small weak tone trial deal. From the commercial account, we know that there are few high market transactions, few inquiry calls, and a slightly pessimistic attitude. The overall market transaction atmosphere is light and most merchants operate on the market. At present, the downstream demand is still low, the demand for terminal replenishment is low, and the purchasing enthusiasm is not high. According to traders' feedback, the current market is in a weak situation of supply and demand. Downstream feedback shows that many projects are shut down and there is a great pressure on funds. However, the relevant economic data and side news are too bearish, so the futures market is difficult to rebound, and the spot market is mainly responsible for the subsequent drop. However, some traders are still willing to maintain their prices, which is mainly due to the high price of post settlement resources and the low inventory at present. The invention relates to a manufacturing method for a double seal socket flexible connection structure of a large diameter spiral welded steel pipe.

Disadvantages: The pipe structure is loose, and it is not resistant to high pressure. It is only suitable for the production of small air conditioning copper pipes.

Plastic coated copper pipe is one of the safe carbon fiber products. Its specific content is a new structural composite building decoration material that can be produced according to the development trend of production and manufacturing by using a glass fiber as the synergist and resin as the adhesive based on the application of full intelligent technical automatic control system equipment.

Quality management.Now let me talk about the damages that are easy to occur on the surface of the copper tube. In order to prevent the accumulation of process agents or products and/or dirt, scratches and other rough surfaces mechanical cleaning must be carried out. If the copper pipe is heated to a certain high temperature in the air during welding or grinding, chromium oxide heat return color will appear on both sides, lower surface and bottom of the weld. The color after tempering is thinner than that of the oxidation protective film, and is clearly visible. The color depends on the thickness. The thicker oxide can be found in the rainbow color, blue, purple to brown. It is usually black. It is caused by being at high temperature or being at high temperature for a long time. When any of these oxide layers exist, the chromium content on the metal surface will, and the corrosion resistance of these areas will. In this case, it is not only necessary to heat temper the color and other oxide layers, but also to clean the chromium poor metal layer under it. Free iron on the surface of t2 copper tube will rust, causing corrosion of stainless steel. Therefore, the powder that must float can usually be removed together with the dust. Some are very sticky and must be treated as embedded iron. In addition to dust, there are many surface iron sources, including cleaning with ordinary carbon steel wire brush and shot peening with sand, glass beads or other abrasives previously used on ordinary carbon steel, low alloy steel or cast iron, or regrinding non stainless steel products attached to copper pipe components and equipment. If there is no protection during cutting or hoisting, the wire ropes, slings and iron on the working surface can easily be embedded or dirty the surface. The copper tube shall be boiled in boiling water for 30 seconds before cold treatment. The effective internal stress is about 15%, and the residual austenite reaches the effect. Then, the cold treatment can be carried out as usual. Of course, the second suggestion is to choose the normal treatment at minus 60 degrees, and then conduct deep cooling at minus 120 degrees. The lower the treatment temperature is, the retained austenite will be rapidly transformed into martensite, but it cannot be transformed. Through experiments, it can be found that there will be about 2% of retained austenite. At this time, retained retained austenite can achieve a certain buffer effect. After cold treatment, which can effectively heat about 40% of the cold treatment stress. Tempering and cold treatment should be carried out as soon as possible after gradual heating, and most of them can avoid cracks as soon as possible,GorontaloAlloy steel, so as to ensure that the products will not deform in later use and facilitate daily storage. The transformation characteristics of the area of each layer of the copper tube during empty drawing affect the asymmetry of the deformation of the metal material. One of its characteristics is that the natural widening of each layer along the wall thickness is not consistent. Of course, the external layer of the copper tube is less, the internal surface layer of the copper tube is larger, and the natural widening of the middle layers is slow from the external layer to the internal surface layer.The technical level of degreasing copper tube for mechanical equipment With the substantial improvement of the manufacturing level of mechanical equipment and the degree of control automation in China, there is still some gap between the technical level of domestic degreasing copper tube production line and the products of foreign counterparts. After years of reform and opening up. The quality of all aspects of degreased copper pipe has also risen by several grades, significantly narrowing the quality gap with the imported production line. The aluminum hose production line and aluminum can production line developed and produced by the company break the technological monopoly of foreign companies, can provide stable and reliable production equipment for domestic and international markets, and make great contributions to the aluminum packaging industry. With the continuous improvement of people's living standards, there will be more and more demand for degreased copper tube products, and its market potential is huge. Problems such as incomplete penetration, deformation, cracks and air holes are easy to occur during the fusion welding of degreased copper tubes. Compared with fusion welding, wood is not melted during brazing, which reduces the impact of large thermal conductivity of base metal on welding quality, prevents the formation of incomplete penetration reduces the tendency to produce pores and cracks, and ensures the performance of weld. Because the base metal is not melted, so that the original service properties of the base metal can be maintained.

The selection of medical copper tube table, and the transaction is affected. According to the feedback from the spot operation, the morning market transaction did not follow the temperature rise: after 9:00, the dealers took turns to raise the price, which was in disorder; Before ten o'clock, it was not as expected, and users were very cautious in purchasing; Around 11:00, the surrounding markets became loose and the price was low. High hanging, low selling, and low volume. The market transaction is carried out in such a trilogy, which is different from the opening. In this process, the mentality of traders has changed: from &turning to shipping&, after all, it has promoted the steel mill to sell before entering their own mouth? This is a &manic& market again: failed to continue to rise, spot prices rose; The construction site plan is not much, and the market transaction is weak - this week's trading days, the spot price rose, and the transaction was less than expected. As of noon, the sales volume of large inventory customers was hundreds of tons, and the shipment was not much. Judging from the transaction in the morning, the selling price of leading resources rose generally. Among the resources in Kuti, and the price of earthquake resistant spiral snail was 5350 yuan; Among the resources provided by the factory, Yonggang and Shagang is 5130 yuan, and the differential between spiral and t2 copper pipes is 360-380 yuan/ton. In terms of the market, the leading market Tangshan narrow band mainstream fell by 30-120 in the early opening. The overall trading situation of copper bars was weak. Some small factories cut prices significantly, and the low price trading was acceptable. Limited production continues market resources are average, weak market, and downstream procurement is cautious. 355 is the consolidation of the medium broadband market. Today's futures continue to fluctuate. Traders are less willing to ship at low prices and have a strong mood. However, under the pressure of futures, and traders were affected by multiple factors to make a small weak tone trial deal. From the commercial account, we know that there are few high market transactions few inquiry calls, and a slightly pessimistic attitude. The overall market transaction atmosphere is light, and most merchants operate on the market. At present, the downstream demand is still low, the demand for terminal replenishment is low, and the purchasing enthusiasm is not high. According to traders' feedback, the current market is in a weak situation of supply and demand. Downstream feedback shows that many projects are shut down and there is a great pressure on funds. However, the relevant economic data and side news are too bearish, so the futures market is difficult to rebound, and the spot market is mainly responsible for the subsequent drop. However,GorontaloAluminum row of cold storage, some traders are still willing to maintain their prices, it is also a necessary equipment in the family. With a table, no fingerprint disposal of medical copper tube is necessary in the catering industry. Only when you cook food can you have a place to enjoy it.

Job description.What problems should we pay attention to in each production. It is a key process to weld copper pipe with correct process. Welding materials, welding speed of t2 copper pipe, welding current, welding voltage, wire arrangement, spacing, inclination and other process parameters will affect the performance of the weld. The residual stress of final welded pipe affected by forming is divided into anti-corrosion performance of copper pipe. Copper pipe is a kind of production of pipe material, which is processed into seamless square pipe. The physical properties of copper tubes are slightly weaker than those of hot-rolled steel tubes. The copper tube adopts a two-step push tube expanding machine, which integrates cone die tube expansion, data medium frequency induction heating and hydraulic press. With effective processing technology, low energy consumption, less infrastructure construction, good products, wide application fields of raw materials and products, and what are the production batches suitable for copper tube testing. When purchasing copper tubes, we pay more attention to their general possibilities and observations, but this is effective for a few customers, but it is time-consuming and labor-intensive for many customers and may not be able to accurately distinguish between them. For such problems, it is recommended to conduct a large number of inspections within a small scope of procurement, and then the following is how to conduct inspections. The dimension tolerance of the cleanliness and wall thickness of the inner cavity of the copper tube is strict. However, in the whole process of electric welding, due to the role of the molten metal material of the air conditioning copper pipe, the thickness of the pipe at the welding point will be uneven, and the inside and outside of the welding will be uneven. This will cause energy consumption of the conveyor. At this time, the internal welding ground must be used for leveling. Next, we will take you to the production process of copper pipe - internal welding and calibration. At present, many materials are also used in the life of red copper pipes. Be as judgmental as possible when buying. In fact, so you should decide how much to use before buying.

As the passivation effect of copper material on the agent is weak, time saving (only two thirds of the time of the original rectifier, or even shorter), material saving (at the same time, raw materials can be saved 30%, and efficiency is high (more than one third of the output value of each savings). The degreased copper tube has less deformation resistance and is easier to form. The original color of copper should be orange or rose, but it is easy to oxidize into purple in the air, so it is also called degreasing copper tube. In terms of conductivity and thermal conductivity, brass rod has no hardness of copper rod, and degreased copper tube is inferior to copper wire. The defatted copper tube Huangtong brand has its own advantages and disadvantages, but the differences are also luminous points. Can affect people's lives, because it can be applied to different aspects. As the conductivity of copper is better than aluminum, copper bus is widely used in electrical equipment, especially in complete power distribution equipment. The UVW phase bus and PE bus in the general distribution cabinet are copper bus; In use, copper bus bars are generally marked with colored letters or painted with colored paint.

Gorontalo.Attention shall be paid to the purchase of red copper pipe in order to study the distribution law of pipeline crack stress field under internal pressure. The simulation ysis and experimental verification are carried out for pipes with cracks of different shapes, different directions, different internal pressures and different sizes. The results show that the stress at the crack tip is much greater than that at the crack center. The crack shape has little effect on the stress. With the increase of the included angle between the crack direction and the pipe axis, the stress at the crack tip first increases and then decreases. With the increase of the pipe internal pressure, crack depth, and crack length, the stress at the crack tip increases linearly. Among them, the effect of crack length on the stress at the crack tip is smaller than that of internal pressure and crack depth. During the construction and operation of long-distance pipeline, due to the influence of pipe manufacturing defects, internal and external loads, stress concentration, the pipeline will produce cracks and expand cracks, which is the most dangerous defect of long-distance pipeline and the main reason for pipeline failure. At present, pipeline cracks are mainly determined by internal testing and non-destructive testing after excavation. Among them, ultrasonic internal testing has a good identification rate for cracks with a length of more than 25 mm, a depth of more than 1 mm in the base metal or a depth of more than 2 mm in the weld; Magnetic flux leakage internal detection has a certain detection rate for cracks with opening more than 0.25mm, but it is difficult to identify and quantify. In NDT, magnetic particle, penetration, eddy current and radiographic methods have high detection and identification rate. The generation and propagation of cracks will cause local stress concentration in the pipeline, which is prone to brittle fracture, fatigue damage, corrosion damage and other failure phenomena, seriously affecting the service performance and reliability of long-distance pipeline. In this paper, the influence of crack shape, direction and size on the stress at the crack tip is yzed by studying the stress field distribution law of copper pipe cracks, which provides a reference for the prevention and control of pipe cracks. What problems will be encountered in the production of copper tubes. The production of copper pipe includes four steps: welding, forming, inspection and pipe expansion.

In addition, quartz sand is used as sand intercalation layer on the long distance uniform pavement in the middle of chemical fiber. Its wall thickness and structure are reasonable and the plastic coated copper pipe laying process stipulates that the plastic coated copper pipe is a non-metallic material pipe with light quality, high strength and corrosion resistance. The glass fiber with epoxy resin based weight relief is coiled on the rotating hollow floor step by step according to the processing technology. It can make full use of the efficacy of raw materials, achieve the goal of applying compressive strength, improve the strength and stiffness, and ensure the reliability and stability of t2 copper tube. FRP sand pipe is accepted by many customers because of its excellent resistance to solvent erosion, light weight, high strength, non fouling, strong durability, low comprehensive project cost, convenient installation, reliability and other advantages. Plastic coated copper pipe is used in: gray and black metallurgy industry, nonferrous plate metallurgy industry, power industry, coal engineering, petroleum industry, chemical industry, electromechanical engineering industry, cotton textile, vehicle and motorcycle processing and manufacturing industry, railway line for industrial production, shipbuilding, engineering construction, light industry, food industry, electronic industry, power, culture and art, sports culture and game entertainment, agriculture and animal husbandry commercial services, treatment and health and its national defense and civilian industries.

In addition, brass has a unique sound, so the gongs, cymbals, bells, horns and other instruments in the East, as well as the western brass instruments, are all made of brass, which is a kind of non-ferrous metal processing bar, with good processing performance and high conductivity. It is mainly divided into copper tube (copper zinc alloy, cheaper). The manufacturing principle of copper tube: All elements without exception reduce the conductivity and thermal conductivity of the copper bar. All elements are dissolved in the copper bar, causing lattice distortion of the copper bar, causing wave dispersion when free electrons flow in a directional direction, increasing the resistivity. On the contrary, there are no or few elements with solid solution in the copper bar, which has little impact on the conductivity and thermal conductivity of the copper bar, Special attention should be paid to the fact that the solid solubility of some elements in the copper bar decreases sharply with the decrease of temperature. The precipitation of simple substances and metal compounds can not only strengthen the copper bar alloy by solid solution and dispersion, but also reduce the conductivity slightly. This is an important alloying principle for the study of high-strength and high conductivity alloys. Here, it should be pointed out that the alloy composed of iron, silicon, chromium and copper bar is a very important high-strength and high conductivity alloy; As the influence of alloy elements on the properties of copper bars is superposition, CoCrZr series alloys are * high-strength and high conductivity alloys; It is not easy to heat. Semi continuous casting copper tube has excellent conductivity. Copper tube has excellent conductivity. Alloy copper to ensure safety and fatigue resistance. Tin phosphor bronze jack adopts hard wire electrical structure without rivet joint or conflict contact, which can ensure excellent touch, good elasticity and smooth dial. Phosphor bronze has high corrosion resistance, wear resistance and will not produce sparks when stamping. It is used for medium speed and heavy load bearings. The working temperature is up to 250 ° C, and the active centering is insensitive to deflection. The bearing force is uniform, and the bearing capacity is high. It can withstand radial load and self lubrication without protection. The company is a manufacturer specializing in the production of various bronze tubes, bronze rods, bronze plates and profiled bronze profiles. Technical advantages: The maximum diameter of bronze bars and pipes can reach 300mm, while that of plates can reach 600mm. The wall thickness of bronze tube can be as small as 4mm. The copper tube is a common bronze material. The aluminum content of copper tube generally does not exceed 5%. Sometimes, an appropriate amount of iron nickel, manganese and other elements are added to further improve the performance. It has high strength and good wear resistance. It is used for copper sleeves and wear resistant parts with high strength. The outstanding feature of t2 copper tube is its good wear resistance. The difference between copper tube and copper tube The copper tube is a copper based alloy with aluminum as the main alloy element. The copper tube is a copper based alloy with tin as the main alloy element. The mechanical properties of copper tube are higher than that of copper tube. The aluminum content of the copper tube in practical application is between 5% and 12%, and the 7% copper tube has good plasticity and is suitable for cold working.