ParksHydraulic straight top lifting platformHow to install and operate reasonably

Regular refueling is necessary for maintenance of the elevator: During the use of the elevator, due to the large load, there is also significant friction between various components, especially the elevator chain and elevator shaft pins. It is necessary to ensure that an appropriate amount of oil is added before each use to ensure flexibility and non jamming during operation. If the elevator is in operation and once&quo; appears; Squeak and Squeak&# quo; The friction sound can be basically determined to be due to a lack of oil in the elevator. It is necessary to immediately stop working and investigate the cause, and cannot forcibly operate, which can easily cause unforeseeable hidden dangers. Summary: Regular refueling is not allowed when maintaining the elevator.

After careful inspection, it was found that it was mainly caused by two reasons

Parks.If the lowering valve is not tightly sealed, check if the lowering valve has electricity. If there is electricity, eliminate the malfunction of the lowering valve itself or replace the lowering valve. The slide valve of the lowering valve must be kept clean and move flexibly.

High altitude work is now also very common, and elevators are also highly demanded by the market. Many high-rise transportation tasks are completed by elevators, with high efficiency and reassuring safety. However, otherwise there may be problems, and no one wants to see such a situation happen. What are the installation precautions for elevators?

.Before using the machine, the staff should carefully inspect the hydraulic and electrical systems to ensure that there are no leaks or bare leaks before use.

Drain all the hydraulic oil in the oil tank, open the oil tank, take out the oil suction filter, clean it, and return it to the oil tank. Install it in its original position. Fill the fuel tank with new oil.

Installing bearings for elevators may seem simple, but it is also important to pay attention to some details, sometimes, some people may think of using a hammer to hammer the bearings for convenience, and use brute force during installation. In fact, directly hitting the bearings with a hammer can cause significant damage to the bearings, which is the main reason for bearing damage and reducing the service life of the bearings. So when installing bearings, we must not go too far. Fortunately, we can place some soft cloth or cardboard on top of them before installing them.

The guide rail type cargo elevator has been inspected and debugged before leaving the factory, and all technical indicators have met the design requirements. When in use, only the power supply needs to be connected, and the hydraulic and electrical systems do not need to be adjusted.

The hydraulic pipeline is probably congested. The hydraulic pipeline is also a particularly important key, checking whether the hydraulic pipeline is smooth. Focus on checking whether there are signs of congestion or jamming in various hydraulic valves, including one-way stop valves, electromagnetic directional valves, proportional control valves, overflow valves,ParksHydraulic lifting platform, etc. If there are problems, the hydraulic valve should be cleaned or replaced in a timely manner, as the hydraulic oil may deteriorate or contain impurities. After the hydraulic oil is permanently used, there may be impurities or deterioration in the hydraulic oil. Take a sample for inspection to see if it contains fluid particles, discoloration, or odor. If necessary, replace the hydraulic oil.

Elevators are now very popular among people and can easily transport goods to high-rise buildings. Among them, hydraulic elevators are more popular among people, and people can choose the one that suits them according to their actual situation. However, during normal work, it is important to pay attention to the lifting speed of hydraulic elevators and avoid making mistakes. So what factors will affect the lifting speed of hydraulic elevators?

Product line.What are the advantages of installing a guide rail type elevator for goods? The advantages of civil engineering are easy to install: there is no need for a machine room above the shaft, and the top layer can be installed at a height of more than 5 meters. The computer room can be located within a radius of 15 meters of the shaft, occupying an area of only 3-4 square meters. The hydraulic elevator is not equipped with a counterweight device to improve the utilization rate of the shaft area. The load and load cylinder of the hydraulic elevator directly act on the foundation pit, and the strength requirement for the shaft is low. A brick structure or brick concrete structure shaft is sufficient.

When encountering overheating in the electric motor during daily maintenance of the elevator it is necessary to quickly park the car, and then continue running. The motor bearings should be smooth and excellent.

Regularly check the connection of each part of the hydraulic elevator remove obstacles, and tighten it if there is any looseness. The tightness of the body connecting bolts should be checked when the body is under pressure, and all connecting shafts must have split pins and be sufficient.

When working at heights exceeding 1.5 meters safety nets or safety belts must be used. Specializing in the production of scissor type elevators, a 20 year old brand with competitive prices and guaranteed quality!

Customer first.When conducting high-altitude operations on dangerous edges such as roofs, suspension bridges, slopes, or cliffs, guardrails or safety nets should be installed on the side facing the air, or safety belts or ropes should be used.

When using the hydraulic lifting platform,ParksFixed hydraulic lifting platform, it is also necessary to check for overheating, as this equipment is equipped with a motor. If the motor is overheated, it may cause damage to the motor. However, replacing a motor is relatively expensive. Therefore during driving or trial operation, it should be stopped immediately, and then the fault that caused the motor to overheat should be checked and eliminated, Only then can the machine continue to be used.

What are the pressures on lifting platforms? The movement of lifting platforms has always been a concern for us. Our usage scenarios are uncertain and most of them are part-time workers. Therefore, in order to better attract customers, we are constantly researching mobile lifting platforms to meet different needs. However,ParksHydraulic mobile lifting platform, for some large logistics or enterprise processing plants, we are still accustomed to using fixed elevators, He has a huge load capacity and strong stability, which can meet the needs of many customers, which is also the use of lifting platforms in China in recent years.

Parks.Although lifting cargo elevators have good safety, in practical work, if we do not pay attention to detailed maintenance, we should pay attention to them when performing daily maintenance.

Avoid, especially during storage. Store in a cool and dry place, and avoid rainy and snowy weather during work.

Familiarity with the usage process and without a doubt, this is the first thing to understand. There are two ways to understand it: first, carefully read the user manual provided by the manufacturer when the hydraulic lifting platform leaves the factory; The second is the equipment that needs to be installed. A professional installation technician will be dispatched to install the hydraulic lifting platform. After the installation is completed, relevant users will be trained on the operating process and safety precautions of the hydraulic lifting platform, and some maintenance matters in the future will also be explained; What should be paid attention to during the running-in period when using hydraulic lifting platforms? Check the wear of components. For newly processed and assembled components, there may be subtle deviations in shape and size that require a period of time for running-in. Therefore, during the running-in period, it is necessary to pay attention to whether there is any rapid wear. If there is any, the manufacturer of the hydraulic lifting platform should handle it in a timely manner to avoid equipment failure; Work between the pins and bearings to ensure that they are not worn, and add some engine oil or grease appropriately; Confirm if there is any noise during the running-in period. If it is found that the hydraulic lifting platform is noisy during operation, there is no need to worry in the early stage. If there are no major problems, the noise will naturally disappear. However, please make sure to promptly produce it and solve the problem; Regularly check if the components are loose. Before use, check if there are any signs of looseness in screws, nuts, retaining rings, oil pipe joints, etc. If there are any, please reinforce or replace them in a timely manner to avoid accidents.