TaiwanHydrauli
TaiwanHydrauliThe above detailed introduction, I believe everyone has a comprehensive understanding and understanding of the use of hydraulic elevators, and these details cannot be ignored during the use process.
When using hydraulic elevators, check the connections of each part during use and tighten them in a timely manner if there is any looseness. All connecting shafts require the use of split pins in order to ensure sufficient use and better utilization.
Taiwan.The lifting platform truck should be placed in a trench position and corresponding anti slip measures should be taken; Remove the gearbox of the equipment, remove the axle oil box,TaiwanHydraulic lifting platform, it should be polished smooth with an oilstone; Under the electric motor, place the sleeper on the trench edge on the inner side of the steel rail use a jack to regularly pull the electric motor and remove the upper tile; How to solve the damage of important equipment in the lifting platform car? Check the status of the bearing pads and oil absorbers, investigate the cause of the damage, replace the bearing pads, and clean the bearing oil box; After assembling all components, install a new oil suction device on the axle oil box and clean the axle oil; Gear oil of gear box shall be as specified; Burning of axle box bearings is a common occurrence which is the burning of outer bearings. In severe cases, it can cause the axle box and wheel set to be fixed together, affecting equipment operation.
The function of a fixed loading and unloading platform truck. The fixed loading and unloading platform truck meets the loading and unloading needs of goods, and has good load-bearing effect, convenient loading and unloading, low consumption, and easy operation. The stability of the loading and unloading process is strong, and the height can be adjusted and lifted to a suitable position to meet the loading and unloading of goods. The later maintenance is in place and the maintenance cost is low.
.In this situation, it is necessary to regularly check all wires and cables used to ensure that there is no damage. When there is wrapping or damage, the parts should be replaced in a timely manner. I believe many people have encountered overheating in electric motors. In this case, it is necessary to stop the motor in a timely manner, and then troubleshoot the problem before continuing to use it. This way, the motor shaft can be used and the effect is good.
From this, it can be seen that the hydraulic lifting platform truck needs to carefully inspect the hydraulic and electrical systems before use, such as their overall weight being relatively light, and their maneuverability being relatively good, allowing even a single person to operate, so they are relatively suitable. The mast columns of its system are equipped with guide wheels, so its lifting and lowering are relatively stable during use. Of course, so as to ensure its size during transportation. Only in this way can you enter the car of a general elevator, and then you can smoothly open the door. Of course, some small and narrow channels are also possible, so we need to pay attention to this point.
When using a hydraulic lifting platform truck, there are many details that cannot be ignored. It mainly uses an external power supply, so when operating, the staff needs to master its operating knowledge, which is the basic content. At the same time, it is also necessary to master corresponding emergency response plans. When processing, it is also necessary to check the corresponding route,TaiwanHousehold elevator, which is the basic content. So in addition, what preparations do hydraulic elevators need to master during use?
Many times, when ordering large lifting platform vehicles, after the customer has determined the parameters, the designer first needs to consider various factors before design, when designing and manufacturing, it is necessary to consider separate assembly or table splitting to meet the requirements. At the same time it is also necessary to consider the bearing capacity of the split body, to ensure that the equipment can be easily transported, lifted, and moved.
From this, it can be seen that the hydraulic lifting platform truck needs to carefully inspect the hydraulic and electrical systems before use, so as to facilitate its use.
Workshop cost.Of course, the hydraulic lifting platform truck uses a dual protection structure, which can make the work relatively safer. When lifting, an appropriate working surface can be selected, so that the lifting platform truck will be safer during operation. The process of operating the hydraulic lifting platform truck should be standardized, so that maintenance and debugging can be carried out before leaving the factory. At the same time, it can also ensure that all technical indicators can meet the design requirements, but it is necessary to connect the ground wire during use. Of course, the hydraulic electrical system does not need to be adjusted in this situation.
When using, the weight should be evenly distributed, mainly in the center of the countertop. However, for special cases, partial loading is allowed, but the longitudinal load cannot exceed half of the rated load. The horizontal load should not exceed one-third of the rated load, so this detail needs to be noted during use.
The characteristics of hydraulic lifting platform vehicles are very obvious, such as their overall weight being relatively light, and their maneuverability being relatively good, allowing even a single person to operate, so they are relatively suitable. The mast columns of its system are equipped with guide wheels, so its lifting and lowering are relatively stable during use. Of course, it is also important to pay attention to the structure of the hydraulic lifting platform truck and ensure its compact structure, so as to ensure its size during transportation. Only in this way can you enter the car of a general elevator and then you can smoothly open the door. Of course, some small and narrow channels are also possible, so we need to pay attention to this point.
The electric lifting platform truck needs to work under load according to the regulations on the nameplate during use, but overloading is strictly prohibited during use. Especially in emergency situations, it can only briefly overload by 10%.
build.There are many details that need to be paid attention to when using an electric lifting platform car, such as placing it on a flat surface during use to prevent tipping during work. In addition, what are the precautions for using electric lifting platform vehicles?
Regularly check all wires and cables for damage, and promptly wrap and replace the damaged parts.
Nowadays, technology is constantly developing and advancing, with electric elevators being a manifestation of technological progress. So what are the characteristics of electric elevators? Let's give you a detailed introduction below.
Taiwan.Of course, the hydraulic lifting platform truck uses a dual protection structure, which can make the work relatively safer. When lifting, an appropriate working surface can be selected, so that the lifting platform truck will be safer during operation. The process of operating the hydraulic lifting platform truck should be standardized, so that maintenance and debugging can be carried out before leaving the factory. At the same time, it can also ensure that all technical indicators can meet the design requirements, but it is necessary to connect the ground wire during use. Of course, the hydraulic electrical system does not need to be adjusted in this situation.
In the current society, so this type of lifting platform car has a very good texture and can be used in places such as home floors during use. Therefore, this type of mobile lifting platform car will not cause damage to the ground during use, making it very convenient to use. The elevator is made of manganese steel, especially its theme frame, which is not easy to corrode during use and is important for convenient storage.
To understand the operation of the mechanism, the main focus is on whether it is normal and whether there is noise during use. When faults are found timely troubleshooting is necessary to ensure the normal operation and use of the machine. During installation, it is necessary to disassemble or adjust the rotating mechanism. In this case it is necessary to ensure that the rotating mechanism can be parallel to the centerline of the reducer and the centerline of the gear, and of course, the meshing clearance should also be appropriate. If this is not appropriate, then the machinery cannot operate normally.