Nai meihengEleThe key to using a hydraulic elevator during normal operation is to determine whether it is operating normally and whether there is noise based on its operating sound.
Regularly check for water accumulation and humidity. It is inevitable for high-altitude work vehicles to drive in rainy and snowy weather, or muddy roads. The bottom and some gaps, as well as the indoor floor, are prone to accumulation of sludge. If the owner does not clean them in a timely manner, this will cause moisture to hide. Therefore, the outer edges of the wheel hub, doors, bottom corners of tree trunks, keyholes and wiper brackets, and other areas of activity should be regularly inspected, and the drainage holes of the doors and various parts should be kept unobstructed to ensure that the car seat covers, such as humidity, carpets, and floors, prevent rusting of accessories.
Nai meiheng.The loading and unloading mobile boarding bridge has become a very common structural form in modern logistics sites. It is the point and endpoint of the enterprise logistics chain, and a loading and unloading operation platform for enterprises to quickly and turnover products and goods. The height of the loading and unloading operation platform is fixed, but there is always a certain height difference or gap between the transportation vehicles and the loading and unloading platform due to the height of the carriage. Causing the forklift to be unable to enter and exit the transportation vehicle for direct loading and unloading of goods. Use the boarding bridge to provide reliable connections. Enable forklift trucks to quickly enter and exit transportation vehicles for loading and unloading operations.
Now we have an increasing demand for cargo elevators. Let me introduce the maintenance work of guide rail cargo elevators to you. When we use a guide rail elevator in our daily life, we need to regularly inspect, maintain and maintain it. This not only extends the service life of the guide rail elevator, but also makes it more powerful when working! For example, the transmission part should have sufficient oil, and vulnerable parts must be regularly inspected, repaired, or replaced. Mechanical bolts, such as slewing bearings and lifting arm connecting bolts, should be checked for looseness. If there is looseness, it must be tightened or replaced immediately. Below is an introduction to the 8 steps of maintenance: important maintenance work for guide rail elevators. Regularly check the tire pressure and bearing condition of the guide rail elevators to ensure they are in good condition; Regularly check whether the structure of the bracket and panel is in good condition, and add oil and grease to the bearings and components in a timely manner, once a month; Vulnerable parts must be regularly inspected, repaired or replaced. Parts that frequently vibrate, such as bolts and slewing bearings, it must be tightened or replaced immediately.
.The transportation equipment for lifting and unloading goods is mostly used for goods transportation between height differences in production lines, material loading and unloading, component lifting during large-scale equipment assembly, fixed three-dimensional parking, and other places. So what is the new price for fixed elevators?
What is the new price for fixed elevators? Fixed elevators are currently very popular in the market. Due to different manufacturers, materials, rated loads, and brand awareness, the prices of fixed elevators produced in the current domestic market vary. The prices of fixed elevators are: rated loads of 1-5 tons, an elevation of 7 meters, a table size of 2500mm * 2000mm, and around 27000-45000 yuan; The rated load is 1-3 tons, the lifting height is 0 meters, and the price is around yuan. The rated load, lifting height, and table size of each fixed elevator vary in price. (Specific bearing capacity and lifting height can be designed and customized according to user requirements)
It is necessary to regularly inspect the brake of the guide rail type cargo elevator, and there should be no dirt on the friction surface.
Now we have an increasing demand for cargo elevators. Let me introduce the maintenance work of guide rail cargo elevators to you. When we use a guide rail elevator in our daily life,Nai meihengPrice scissors hydraulic lifting platform, we need to regularly inspect maintain, and maintain it. This not only extends the service life of the guide rail elevator, but also makes it more powerful when working! For example, the transmission part should have sufficient oil, and vulnerable parts must be regularly inspected, repaired, or replaced. Mechanical bolts, especially parts that frequently vibrate, such as slewing bearings and lifting arm connecting bolts, should be checked for looseness. If there is looseness, it must be tightened or replaced immediately. Below is an introduction to the 8 steps of maintenance: important maintenance work for guide rail elevators. Regularly check the tire pressure and bearing condition of the guide rail elevators to ensure they are in good condition; Regularly check whether the structure of the bracket and panel is in good condition, and add oil and grease to the bearings and components in a timely manner, once a month; Vulnerable parts must be regularly inspected,Nai meihengBasement hydraulic lifting platform, repaired, or replaced. Parts that frequently vibrate, such as bolts and slewing bearings, should be checked for looseness. If there is looseness, it must be tightened or replaced immediately.
Fault analysis of mobile elevators: Mobile elevators cannot lift or have weak lifting force: overflow valve pressure regulation does not meet the requirements: adjust the pressure to the required value; Oil cylinder internal leakage: check or exchange oil cylinder components; Clamping or internal leakage of directional valve: Check or exchange valve components; If the oil level is too low and the oil inlet filter is blocked, add enough oil and clean the filter. The fuel supply pump has drawbacks: check or exchange the pump.
When installing, disassembling, attention should be paid to ensuring that the center line of the exhibition organization reducer is parallel to the center line of the gear, and its meshing surface is not less than 70%, and the meshing interval should be appropriate.
original.It is good not to cover the car with clothes for high-altitude work vehicles. If the vehicle is parked outside in windy and rainy weather, the clothes will repeatedly slap the car paint, especially if the car is blowing sand on the clothes, because over time, it will lead to black paint. In addition, when the wind does not directly spray powder or clean the mechanism on the sand, it should be washed with water and prevent the high-altitude work vehicle vacuum cleaner from scratching the sand particles on the paint surface.
Attention should be paid to inspecting whether each steel wire rope has broken wires and loose strands. If it exceeds the relevant regulations it must be replaced immediately. The care and maintenance of steel wire ropes should strictly follow the regulations.
Regularly check for water accumulation and humidity. It is inevitable for high-altitude work vehicles to drive in rainy and snowy weather, or muddy roads. The bottom and some gaps, as well as the indoor floor, are prone to accumulation of sludge. If the owner does not clean them in a timely manner, this will cause moisture to hide. Therefore, the outer edges of the wheel hub, doors, bottom corners of tree trunks, keyholes and wiper brackets, and other areas of activity should be regularly inspected, and the drainage holes of the doors and various parts should be kept unobstructed to ensure that the car seat covers, such as humidity, carpets, and floors, prevent rusting of accessories.
Usually, all wires and cables are inspected for damage. We need to quickly bandage and replace the damaged department. Professional elevator manufacturer with quality assurance, professional company, timely supply,Nai meihengFully automatic hydraulic lifting platform, high cost-effectiveness, has become the preferred brand for many wire products. Welcome to purchase!
Professional is king.Prepare the foundation according to the basic plan, pay attention to finding, leveling, and aligning points, and ensure the level of the foundation and various usage requirements.
Check, adjust, and replace defective parts of the heavy operating rod mechanism; Clean the valve components; Check the cleanliness of the hydraulic oil valve core for clamping (manufacturing, installation issues, dirt issues)
What is the new price for fixed elevators? Fixed elevators are currently very popular in the market. Due to different manufacturers, materials, rated loads, and brand awareness, the prices of fixed elevators produced in the current domestic market vary. The prices of fixed elevators are: rated loads of 1-5 tons, an elevation of 7 meters, a table size of 2500mm * 2000mm, the lifting height is 0 meters, the table size is 2300mm * 2000mm, and the price is around yuan. The rated load lifting height, and table size of each fixed elevator vary in price. (Specific bearing capacity and lifting height can be designed and customized according to user requirements)
Nai meiheng.The transportation equipment for lifting and unloading goods is mostly used for goods transportation between height differences in production lines, material loading and unloading, component lifting during large-scale equipment assembly, fixed three-dimensional parking, it is necessary to check whether each organization operates normally and whether there is any noise. If any obstacles are found they must be quickly eliminated.
Now that you understand how to use a hydraulic lift, and improves the efficiency and quality of the lowering work.