Abquiki20 meteThe advantages and application fields of elevators and lifting platforms. The lifting mechanism is made of high-strength manganese steel giant tubes. Equipped with safety maintenance equipment to avoid overloading of elevators. Equipped with a safety maintenance valve to prevent hydraulic pipeline cracking. Equipped with emergency lowering equipment in case of power outage. This product is suitable for mobile high-altitude operations such as high-altitude equipment and maintenance in various industries.
Unscrew the screws on the dustproof hole on the outer side of the elevator flange, adjust the PCS system ring to align its side hole with the dustproof hole, and tighten the inner hexagon. Afterwards, remove the motor shaft key.
Abquiki.The anti-corrosion measures for the body of high-altitude work vehicles should pay attention to small scratches. The paint surface of high-altitude work vehicles often corrodes. In addition to common collisions, scratches, and small rocks on the driving tires, there can also be a peeling point, which will cause a small rust over time. Because most of these scars are small and easily overlooked. Therefore, regular inspections should be conducted on the engine hood and surrounding areas. Once discovered, it is necessary to promptly go to a professional beauty shop for processing.
During the use of hydraulic elevators, if not properly operated, there will always be problems. Many customers have reported that hydraulic elevators sometimes cannot be lifted. If the hydraulic lift pump can continue to work, other issues need to be considered. Below, the editor will explain the reasons for the hydraulic lift pump station not being oiled and solve the reasons for the hydraulic lift pump station not being oiled, as well as the solutions for mobile elevators The analysis of the pump station of hydraulic elevators such as guide rail elevators is as follows: the motor power supply is abnormal or reversed; The solution is to correctly connect the motor power supply or adjust the steering mailbox to ensure there is no hydraulic oil or insufficient oil; The solution is to add hydraulic oil.
.Outdoor elevators and factory cargo elevators are heavy lifting mechanical equipment. Outdoor elevators are used for transporting goods between floors of buildings, and are specialized hydraulic cargo elevator products. They are mainly used for transporting goods up and down between various working floors; Vertical garage and car lift between garage floors. The hydraulic system of the product is equipped with anti fall and overload protection devices, and operation buttons can be set on each floor and lifting platform workbench to achieve multi-point operation.
The size of the oil cylinder should be minimized as much as possible while meeting the design requirements. The smaller the size of the oil cylinder, the faster the lifting speed.
What kind of function can be achieved by installing the elevator? Before installation, confirm whether the motor and elevator are intact and strictly check whether the dimensions of each part connected to the motor and elevator match. Here are the dimensions and fit tolerances of the positioning boss, input shaft, and elevator groove of the motor.
The operation of the single column aluminum alloy elevator is relatively convenient. The gantry is easy to assemble across the frame, with labor-saving operation and flexible movement. It can cross obstacles such as fixed seats with a height of up to 1m, with good rigidity and stability. Equipped with universal casters for flexible mobility. The span of the two end brackets can be adjusted,AbquikiElevator, which is suitable for crossing different obstacles. The two end brackets are vertically adjustable and can be used for operations on slopes or steps with a certain slope.
Now we have an increasing demand for cargo elevators. Let me introduce the maintenance work of guide rail cargo elevators to you. When we use a guide rail elevator in our daily life, we need to regularly inspect, maintain, and maintain it. This not only extends the service life of the guide rail elevator, but also makes it more powerful when working!
Remove and disassemble the lowering valve, blow the valve core clean with compressed air, and then reinstall it.
quality index.Unscrew the screws on the dustproof hole on the outer side of the elevator flange, adjust the PCS system ring to align its side hole with the dustproof hole, and tighten the inner hexagon. Afterwards, remove the motor shaft key.
When conducting high-altitude operations on dangerous edges such as roofs, suspension bridges, slopes, or cliffs guardrails or safety nets should be installed on the side facing the air, or safety belts or ropes should be used.
Many people believe that the mechanical strength of the elevator itself is relatively high when using it so during the installation process, there is no
The method is that it may cause increased wear and inflexibility of the parts, and it is also important to pay attention to the installation precautions corresponding to the working environment and not be careless. Proper installation, when installing the elevator, please be sure to strictly follow the installation and use related matters below, and carefully assemble and use it.
Equipment maintenance.Use a heavy crane to lift the cage and accurately position it from above the standard section; Place the two suspension cages on the guide rail frame and slowly place them on the buffer spring. Prepare the drive frames of the two suspension cages and adjust each back wheel and roller to a position with a large gap to facilitate the installation of the drive frame. Install a standard section on the basic part of the elevator using heavy equipment and tighten the connecting bolts. Install two sets of drive frames above each suspension cage using heavy equipment and thread the connecting pins, and install the cage top guardrail.
What is the new price for fixed elevators? Fixed elevators are currently very popular in the market. Due to different manufacturers, materials, rated loads, and brand awareness, the prices of fixed elevators produced in the current domestic market vary. The prices of fixed elevators are: rated loads of 1-5 tons an elevation of 7 meters, a table size of 2500mm * 2000mm, and around 27000-45000 yuan; The rated load is 1-3 tons, the lifting height is 0 meters, the table size is 2300mm * 2000mm, and the price is around yuan. The rated load,AbquikiElevator small conveyor,AbquikiCustomized lifting platform by manufacturer, lifting height, and table size of each fixed elevator vary in price. (Specific bearing capacity and lifting height can be designed and customized according to user requirements)
When the motor connection of the elevator is incorrect, when a coil, or one phase winding group is connected in reverse, it can cause serious three-phase current imbalance and cause the winding to overheat.
Abquiki.High altitude work is now also very common, and elevators are also highly demanded by the market. Many high-rise transportation tasks are completed by elevators, with high efficiency and reassuring safety. However, attention should also be paid to the installation of the elevator, otherwise there may be problems, and no one wants to see such a situation happen. What are the installation precautions for elevators?
The operation of the single column aluminum alloy elevator is relatively convenient. The gantry is easy to assemble across the frame, with labor-saving operation and flexible movement. It can cross obstacles such as fixed seats with a height of up to 1m, and can operate stably on steps. Made of high-strength rectangular steel pipes, with good rigidity and stability. Equipped with universal casters for flexible mobility. The span of the two end brackets can be adjusted, which is suitable for crossing different obstacles. The two end brackets are vertically adjustable and can be used for operations on slopes or steps with a certain slope.
Three column aluminum alloy elevator: Three sets of masts support the synchronous lifting of the working platform, and the support structure is the same as that of a single masted platform, with super large load capacity and work stability. The overall lifting guardrail device has good strength and greatly reduces the height of the entire machine during transportation. It is very convenient for loading and unloading, and can be assembled or disassembled in one lift.