VillebanElevat
VillebanWarehoDifferent. (Specific bearing capacity and lifting height can be designed and customized according to user requirements)
Systems: explosion-proof electronic control system, remote control system, PIC system.
Villeban.How to install and use the bearings of the elevator During the process of installing the bearing device of the elevator, we cannot always ensure that the bearing device has the correct orientation, which inevitably leads to some devices not in place or bearing misalignment. Once these problems occur in the device the clearance between the bearings becomes too small, and then the inner and outer rings of the bearings cannot be located at the same rotation center. Therefore, when installing bearings it is necessary to use specialized tools, and in the future, it is also necessary to use a detector to test the bearing device, so as to ensure the success of the bearing device.
Fixed elevator is a transportation equipment that directly lifts and loads goods from the ground. It is mainly used for goods transportation between height differences in production lines, material loading and unloading, component lifting during assembly of large equipment, fixed three-dimensional parking, such as lifting a certain layer of the warehouse to transport goods or personnel to a designated warehouse location.
The motor winding is short-circuited. When a short circuit fault occurs in the motor winding, the short circuit current is much larger than the normal working current, causing the winding to overheat or even burn out.
Walking: assisted self-propelled, two wheel traction, self driving, and car modification.
Scissor type fixed lifting platform is a transportation and loading equipment that transports goods from one height to another. After operation, the platform is level with the ground, without occupying ground space and affecting passage passage.
Manual hydraulic lifting platform application Manual hydraulic platform performance: The manual hydraulic platform truck is made of high-strength steel, with a reasonable and compact design structure, safety, and reliability. It is equipped with a safety valve, a fully sealed oil cylinder, and a manual hydraulic system for lifting and lowering, making it easy to operate. Equipped with a guide wheel to save the operator's physical strength,VillebanGuide rail type lifting cargo elevator, and can protect the load wheel and pallet load wheel. Unique hydraulic pump design, the pump is simple and designed to maintain an ideal height for pipeline loading and unloading operations; The unique design concept makes the operator's operation simple and convenient.
Precautions for using guide rail type elevators: Overloading and transporting flammable and explosive products are strictly prohibited.
Inspection standard.Incorrect connection of the elevator motor When a coil, coil group, or one phase winding group is connected inversely, it can cause a serious imbalance in the three-phase current and cause the winding to overheat.
Test the goods elevator every day to see if it can operate normally.
In addition to having a fixed mode,VillebanSmall cargo elevator, there are also types of mobile elevators. As the name implies, it is a combination of lifting equipment and on-board systems. This type of lifting equipment is very flexible to move, and of course, it is better to use it. For example, there are such lifting equipment in airports, and stations or stadiums may also be equipped with such equipment, as it can be moved by itself, The scope of work is not limited to a certain place, but can be used wherever lifting operations are required. For example, when installing outdoor advertisements, some advertisements are relatively high in height. At this time, mobile lifting equipment can be used to send billboards or staff to a designated height for work. This type of equipment can also be divided into two types according to the driving mode: hydraulic lifting and electric lifting. The so-called hydraulic lifting is the use of hydraulic oil to drive to achieve a specified height. The electric mode is driven by a motor or tooth to lift to a certain height. However, currently, two wheel traction, self driving, and car modification.
The cost is reasonable.The water cooling of hydraulic stations is generally tubular water cooling, and the type selection is based on the heat load to calculate the heat exchange area, and the heat exchange capacity is calculated based on the heat load. Then, the type selection calculation is performed when the flow can be satisfied. Therefore, the two types of cooling are different and there are significant differences. Long-term lifting and lowering of cargo elevator factory
Failure Analysis of Mobile Elevator
Secondly, there should be no dirt on the friction surface. If there is any dirt, it should be washed off with gasoline or thinner; The reduction gearbox, gearbox, external meshing gear, and other parts of the equipment, as well as the hydraulic oil, must be tested according to the requirements in the table; Correct maintenance of the hydraulic guide rail elevator: Regularly inspect the wire ropes at various parts for broken wires and looseness. If any such phenomenon is found, replace it in a timely manner. The maintenance of the wire ropes must be carried out in strict accordance with the specifications; Check the connection condition of each part according to the braking rules and regulations. If there is any looseness, tighten it in a timely manner. Check the tightness of the connecting bolts of the equipment when the body is under pressure. All connecting shafts should be equipped with cotter pins; Check whether the operation of each mechanism is normal, whether there are noises and faults according to regulations, and promptly remove all faults; When installing, disassembling, and adjusting the rotating mechanism of the equipment, it is important to note that the reducer and the gear center line should be parallel,VillebanElevating cargo elevator factory building, and the meshing clearance should be appropriate; Regularly conduct a comprehensive inspection of the equipment to see if there is any damage to the wires and cables, and if there is overheating of the motor. Replace the motor in a timely manner and eliminate the fault before continuing operation; Ensure that the bearings, boxes distribution boxes, and brushes of the motor are kept clean, and that the travel switch points of each safety device must be safe and reliable.
Villeban.Test the goods elevator every day to see if it can operate normally.
In addition, it is strictly prohibited to use a hammer during installation to prevent excessive axial or radial force from damaging the bearings or gears. Be sure to tighten the mounting bolts before tightening the tension bolts. Before installation, clean the anti rust oil on the motor input shaft, positioning boss, and elevator connection parts with gasoline or zinc sodium water. Its purpose is to ensure the tightness of the connection and the flexibility of operation, and to prevent unnecessary wear and tear.
Precautions for using guide rail type elevators: Overloading and transporting flammable and explosive products are strictly prohibited.