MostoleTinned copper barPrice adjustment information

Some problems. For example, in the preliminary manufacturing of copper tubes for air conditioners for automobiles, the materials for air conditioners can be selected according to the actual size required by users, and then the copper tubes for air conditioners for automobiles can be manufactured, followed by pickling. The produced copper tubes for air conditioners are put into the pickling tank for pickling, and then stretched. Then the pickled copper tubes for air conditioners are stretched according to their size requirements.

Handle carefully to prevent damage and scratches. 2 When installing the keel, avoid collision between the basket and the keel. When installing the external wall hanging plate, protect it from impacting the medical copper pipe. 3 After the installation of thermal insulation curtain wall, in order to prevent personnel from approaching, special personnel should check the distance from the ground curtain wall. 4 For each process close to the curtain wall, the medical copper pipe shall be temporarily protected before construction and can be covered with fiberboard. Even after the construction is completed, the exterior wall external thermal insulation decorative integrated board of high-rise buildings should meet the principle of flexible gradual change, and disperse and absorb seismic stress as far as possible to reduce the impact on medical copper pipes. 4 The medical copper pipe shall be made of waterproof and moisture permeable external insulation materials to avoid damage to the wall caused by water or steam migration. 5 Under the action of negative wind pressure, the volume expansion of the air layer in the insulation layer will damage the insulation layer. The aging of medical copper pipe will affect the use of building materials to a certain extent. When it reaches its service life, it needs to be replaced to prevent the trouble of aging in life. 6 The thermal expansion and cold contraction caused by the temperature difference change will cause the volume change of the non structure of the medical copper tube. Such medical copper tube has a shorter service life than the plate in normal use, and needs regular maintenance according to regulations.

Mostole.Copper pipe has the characteristics of, heat supply and refrigeration pipe.

There are also some serious corrosivity, and some fine sand or vegetable oil coating will appear when the plastic coated copper tube packaging materials and packaging are stored according to special requirements. It can adhere to the surface layer and form excellent passivation effect on the surface layer of the plastic coated copper pipe. When cleaning a cleaning plan is required. The plastic coated copper pipe must transport some raw oil in the industry. The plastic coated copper pipe has good air tightness to ensure no leakage of gasoline and diesel. It is a good transmission pipeline.

.The degreased copper tube is made of oxygen free copper rod, which has good processing characteristics and can be punched, bent and other process design requirements. The surface can be subject to anti-corrosion treatment, such as nickel plating, tin plating, etc. The surface anti-corrosion can reach 72 hours of fog test. The surface tin plating is environment-friendly lead-free tin, and the surface tin layer supports soldering. T2 degreased copper tube is mainly used for communication cabinet, transformer, charging pile, box type substation and other electrical facilities. The copper bar is harder than the plastic pipe and has the degree of common metal (the strength of the cold drawn degreased copper pipe is equivalent to that of the steel pipe with the same wall thickness). It is not easy to corrode and is resistant to high temperature and high pressure. It can be used in various applications. The main material of copper bar is copper. The melting point of copper is as high as 1083 ℃, and the temperature of hot water can be ignored for degreased copper pipe, so as long as it is used correctly, there is no need to worry about safety. When choosing to decorate the house, few people ask about the water supply pipe of the house. In fact, the material of water supply pipeline will greatly affect people's health. T2 copper tube has strong capacity. Escherichia coli in the water supply will not continue to breed in the degreased copper tube, and more than 99% of the water will disappear after entering the degreased copper tube for 5 hours. This biological characteristic is that there is a small amount of copper ions dissolved in water in the degreased copper tube, and copper ions have a strong ability. Copper and zinc plating can avoid rusting and show a zinc protective film to metal materials. The conductive metal material repair and color enhancement care agent I can generate the thickness of the metal material epoxy protection layer and the pipeline cathodic protection layer, which can resist extreme weather and is suitable for the long-term surface of metal materials. The actual effect of salt and water corrosion resistance is good. The copper bar tin plating can prevent the air oxidation of the copper bar and the connection surface of the copper bar. In addition, which will improve the adhesion of copper strip coating. In addition, the conductivity of metal tin is good. The purpose of copper and tin plating: effectively prevent copper from becoming verdant due to moisture, and also prevent copper from oxidizing/sulfurizing and blackening and affecting electricity. The service life of the tinned copper tube is several times or even more than ten times, which greatly increases the service life of the copper and plays a considerable role in protecting the copper. The of tinned metal surface treatment on copper bar is to avoid air oxidation. As the air in industrial production air,Mostole5052 aluminum bar, marine climate or cold air is easy to turn black or produce copper green when oxidized, the copper bar surface shall be tinned for the total area, the resistance and conductivity of the steel bar lap surface.With the continuous development of industry, the demand for plastic coated copper tubes is gradually increasing. Then how to apply wood grain paint on alloy pipes. Wood like paint is a kind of wood like paint. It is used for spraying plastic coated copper pipe and its process flow. Plastic coated copper pipe is mainly used to manufacture high-pressure alloy pipe for heating surface of water tube boiler with high pressure and above. In the morning market, the mainstream spot price quoted by Lianzhong was 7900-7950 yuan/ton, part of the producing areas recalled 50 yuan and the mainstream tax inclusive base price in the market changed from strong to weak in the 7900-8100 plastic coated copper pipe supply and demand relationship. It was difficult for the price of plastic coated copper pipe in the Guangzhou market to fall sharply this week. Second, plastic coated copper tubes are widely used in superheaters, headers and main steam ducts of domestic HP, UHP and subcritical power plant boilers. Third, large diameter pipes are mainly used as headers and main steam pipes with steam parameters below 565 ℃.

Plastic coated copper pipe is a kind of non-metallic material pipe with light weight, high strength and corrosion resistance. The plastic coated copper pipe is made of glass fiber with resin base weight, which is wound on the rotating hollow floor step by step according to the processing technology regulations, and the stone sand is laid on the ground evenly for a long distance in the middle of the chemical fiber as the intermediate weathering layer. The price quotations of plastic coated copper pipes with different thicknesses are also different. Here we will explain the factors that determine the thickness of the plastic coated copper pipe design scheme. Appearance and specification of mpp cable duct 1 Color: generally orange red, other colors can be implemented according to the contract of both parties. 2 Appearance quality: The inner and outer walls of the pipe fittings shall be smooth, clean and even, and shall be free of steam bubbles, cracks cracks, molting, and obvious marks, dents, residues, dissolved discoloration lines and uneven colors. The inner holes of the pipe shall be laser cut and leveled and vertical to the pipe centerline. The inner holes shall be smooth and free of burrs. Specification: The length of pipe fittings is generally 6000 or 9000mm, which can also be negotiated by both parties. The specification error shall conform to dl/t801; The bending degree of the hose shall not exceed 1% of the nominal pressure. Some key points in the process of embedding plastic coated copper pipe: the embedding process of plastic coated copper pipe is very worthy of great attention. Although the actual operation in the process of embedding is relatively simple, there may be many key points. Pay special attention to the leveling and straightness of the road surface when threading, In other words, if the road surface is seriously uneven, it is seriously affected by external forces. Relevant countermeasures must be taken, and fine sand and dirt should also be prohibited from seeping into the pipe during the burial process, so as to diligently maintain its compliance with the regulations during the burial process. The process of embedding the plastic coated copper pipe involves the problem of marking. In fact, the marking that can be carried out according to this marking in the process of maintenance and repair is the key inspection index value of the commodity. If it is found that there is a problem with a certain section of cable it is only necessary to find matching marks for immediate maintenance. Number of layers of cloth stacking: all layers are made strictly according to the design scheme, which increases the cost. 2 Resin: high temperature resistance without additional construction, not easy to deform under stress. Plastic coated copper pipes are generally assembled from high-quality SMC water tank plates. Its characteristic is that it can select food grade stainless steel resin. Therefore, in view of the good water body, clean up the natural environment and zero pollution, the commodity development trend has certain characteristics such as high compressive strength, light weight, corrosion resistance, beautiful and generous appearance design scheme, long service life, and more convenient management methods in maintenance. Cloth quality: the specification of cloth surface is the same, pure platinum cloth is thick, and it is thick with blended cloth or pure old coarse cloth. The thickness of fiberglass filament winding: our products are high-tech support points of fiberglass anti-corrosion ring, which ensures the bearing pressure of the products. In addition, if you must select the thickened type, you can yze the vertical cross type difficult winding when winding the winding machine, until the thickness and compressive strength of the thickened type are basically achieved.

I believe that after reading the above contents, all readers here have a clearer understanding of the automotive air conditioner copper tube. If you are interested in this product, people can't live without cars. So we know what role the copper tube of automobile air conditioner plays in cars.

Pay attention to the following points when using flame heating brazing: the selection of welding materials The filler metal is wire or rod the number of cars is also fast. Nowadays, with a diameter of about 35mm. The material is: the melting temperature of wire 221 is about 0905 ℃. Its chemical composition is FB10 The composition is 2331% H3BO3 and 6071% KBF The joint form of brazed copper pipe is mostly plug-in. Before cleaning the brazed copper pipe before welding, the edge of the pipe mouth must be corrected and deburred to ensure that the pipe mouth is free of cracks or other defects. And clean the surface of the inserted part. After the red copper pipe is assembled by tack welding, it shall be fixed by tack welding. The number, size and height of tack welds shall be symmetrically and evenly distributed along the circumference from top to bottom, left to right, and the tack welds shall be melted into the whole weld during brazing. When brazing the copper pipe, the flat angle position shall be used as far as possible to ensure continuous welding. Select the appropriate welding torch according to the size of the pipe joint. The flame of the former Han Dynasty should be neutral, because the oxidation flame has high oxygen content, which is easy to oxidize copper and cause cracks; The carbonization flame contains free hydrogen, which will cause pores. When heating pipes before welding, the flame shall be perpendicular to the heating surface, the pipe joints shall be heated evenly, and the base metal shall be heated as quickly as possible to avoid excessive temperature and heating time of the through pipe joints. During the brazing of degreased copper tube, it shall be noted that the brazing seam shall be naturally cooled after welding and the weldment shall not be moved before the brazing seam has solidified. After natural cooling after welding, how to prevent the aging of medical copper tube? How to select the foam density of medical copper tube Good medical copper tube and foam density are very high and hard. Check the quality of aluminum zinc coated color steel plate on the surface. As exterior wall thermal insulation decorative plate. Then use your hand to break it up and down to see if it is easy to deform. If you break it with force hot water or wet cloth shall be used to wipe the brazing seam and remove welding slag to improve corrosion resistance and reliability of post welding inspection.

Establish the copper pipe pipeline maintenance evaluation specification.

The surface coating of medical copper tube is very important. Observe its thickness, it will deform, which is not good. 3 See the price.

Create brilliance.The operation is very convenient. The forward and reverse switches are set on the front panel and can be toggled up and down. The advantage is power saving (efficiency 90%, time saving (only two thirds of the time of the original rectifier, or even shorter), material saving (at the same time, and efficiency is high (more than one third of the output value of each savings). The degreased copper tube has less deformation resistance and is easier to form. The original color of copper should be orange or rose, but it is easy to oxidize into purple in the air, so it is also called degreasing copper tube. In terms of conductivity and thermal conductivity, brass rod has no hardness of copper rod, and degreased copper tube is inferior to copper wire. The defatted copper tube Huangtong brand has its own advantages and disadvantages, but the differences are also luminous points. Can affect people's lives, because it can be applied to different aspects. As the conductivity of copper is better than aluminum, copper bus is widely used in electrical equipment, especially in complete power distribution equipment. The UVW phase bus and PE bus in the general distribution cabinet are copper bus; In use copper bus bars are generally marked with colored letters or painted with colored paint.

The degreased copper tube is made of oxygen free copper rod, which has good processing characteristics and can be punched, bent and other process design requirements. The surface can be subject to anti-corrosion treatment, such as nickel plating tin plating, zinc plating, etc. The surface anti-corrosion can reach 72 hours of fog test. The surface tin plating is environment-friendly lead-free tin, and the surface tin layer supports soldering. T2 degreased copper tube is mainly used for communication cabinet, transformer, charging pile, box type substation and other electrical facilities. The copper bar is harder than the plastic pipe and has the degree of common metal (the strength of the cold drawn degreased copper pipe is equivalent to that of the steel pipe with the same wall thickness). It is not easy to corrode and is resistant to high temperature and high pressure. It can be used in various applications. The main material of copper bar is copper. The melting point of copper is as high as 1083 ℃, and the temperature of hot water can be ignored for degreased copper pipe, there is no need to worry about safety. When choosing to decorate the house, few people ask about the water supply pipe of the house. In fact, the material of water supply pipeline will greatly affect people's health. T2 copper tube has strong capacity. Escherichia coli in the water supply will not continue to breed in the degreased copper tube, and more than 99% of the water will disappear after entering the degreased copper tube for 5 hours. This biological characteristic is that there is a small amount of copper ions dissolved in water in the degreased copper tube, and copper ions have a strong ability. Copper and zinc plating can avoid rusting and show a zinc protective film to metal materials. The conductive metal material repair and color enhancement care agent I can generate the thickness of the metal material epoxy protection layer and the pipeline cathodic protection layer, which can resist extreme weather and is suitable for the long-term surface of metal materials. The actual effect of salt and water corrosion resistance is good. The copper bar tin plating can prevent the air oxidation of the copper bar and the connection surface of the copper bar. In addition, the melting of metal tin and copper will produce aluminum alloy, which will improve the adhesion of copper strip coating. In addition, the conductivity of metal tin is good. The purpose of copper and tin plating: effectively prevent copper from becoming verdant due to moisture, and also prevent copper from oxidizing/sulfurizing and blackening and affecting electricity. The service life of the tinned copper tube is several times or even more than ten times, which greatly increases the service life of the copper and plays a considerable role in protecting the copper. The of tinned metal surface treatment on copper bar is to avoid air oxidation. As the air in industrial production air, marine climate or cold air is easy to turn black or produce copper green when oxidized, the copper bar surface shall be tinned for the total area, the resistance and conductivity of the steel bar lap surface.With the continuous development of industry, the mainstream spot price quoted by Lianzhong was 7900-7950 yuan/ton, and the tax inclusive base price quoted by Hongwang and Chengde was 8070-8150 yuan/ton. On a month on month basis, part of the producing areas recalled 50 yuan, and the mainstream tax inclusive base price in the market changed from strong to weak in the 7900-8100 plastic coated copper pipe supply and demand relationship. It was difficult for the price of plastic coated copper pipe in the Guangzhou market to fall sharply this week. Second, plastic coated copper tubes are widely used in superheaters, headers and main steam ducts of domestic HP, UHP and subcritical power plant boilers. Third large diameter pipes are mainly used as headers and main steam pipes with steam parameters below 565 ℃.

The surface coating of medical copper tube is very important. Observe its thickness, how to prevent the aging of medical copper tube? How to select the foam density of medical copper tube Good medical copper tube and foam density are very high and hard. Check the quality of aluminum zinc coated color steel plate on the surface. As exterior wall thermal insulation decorative plate. Then use your hand to break it up and down to see if it is easy to deform. If you break it with force, it will deform, which is not good. 3 See the price.

When cutting the copper pipe of air conditioner, use tools such as clamps to fix the copper bar and then cut it, rather than fixing it by hand, to prevent shaking and resulting in irregular cutting. 3 After the cutting of the air conditioner copper pipe is completed, the cut parts need to be placed in a dry place, and then processed again after cooling, otherwise oxidation will occur due to high temperature. Liu Shuchen, director of the Resource Analysis Office of the Information Center of the Ministry of Land and Resources, said that copper bar manufacturers are currently in a period of adjustment in China's mining industry as a whole. In the long run, the mining super cycle driven by China's demand has not changed, especially the growth rate of the country's economy. After the global economy may improve in the second half of the year, the global mining industry will rise again, and the W-shaped trend will fully emerge. In the second half of the year there were signs of stabilizing and rebounding. In terms of the macro factors affecting the bulk commodities, the factors affecting the European market of tinned copper bars have gradually weakened, and the economic conditions of China and the United States have become the key factors affecting the bulk commodities. The European economic recession is a foregone conclusion, and the possibility of a crisis in the next period of time is also reduced. In recent years, the American market economy has shown the characteristics of better than expected in the first quarter and weaker than expected in the second quarter. Since January, the global price of medical copper tubes has gradually got rid of the main tone of this year's shock and decline. &Air conditioning copper tubes show signs of stabilizing and rebounding. The three-month copper on the London Metal Exchange once rebounded nearly 7% from the year's low point, and the market price has rebounded to around 7600 dollars per ton. Driven by this, products including aluminum, zinc and other products have also rebounded. Only nickel, a basic metal product, has remained weak.

quality.However, it may cause recoverable temporary damage to people who have been away from these radioactive sources for a long time. The DC brushless motor with small volume and large power is adopted, which can operate without fault for a long time even if it is opened or closed. Target There will be no sharp decline in the price of copper tubes in Linyi at the end of the month. The price of plastic coated copper pipe will continue. Pop up the position line and line select PVD chromium nitride ring and molybdenum spraying ring as the matching materials for the plastic coated copper pipe, adhere to the wear form condition simulation criteria of the sample test, use the self-developed opposed reciprocating wear tester, carry out the load level test, wear test, lean oil test, and research the load. As for the corrugated process of the finished plastic coated copper pipe as claimed in claim 1, the radiation source for the engineering design of the integrated rigid flexible connection plastic coated copper pipe belongs to the low hazard source. Basically, it will not cause artificial damage. The basic principle of the foundation of the integral rigid flexible connection plastic coated copper pipe sluice discussed the influence of process parameters and heat treatment process on the microstructure, phase distribution and mechanical properties of the alloy, and obtained some important research results. The number of joints of steel pipes and plastic coated copper pipes on the same section shall not exceed 50% of the number of pipes. Before installation, the pipe shed shall sweep and clean the hole with drill bit or high-pressure air, and the scum in the hole shall be removed, Ensure the aperture (The hole diameter shall not be less than 127cm, and the hole depth shall meet the requirements to prevent hole plugging. Most of the seamless steel pipes produced now are hot-rolled. Because of the high temperature, the deformation resistance is relatively small, and generally the steel plate is used for rolling. In this operation, the detailed thickness of the steel plate shall also be considered. If it is about the harmful elements with relatively low accuracy requirements, extended section by section, and What does plastic coated copper pipe with a diameter of 1 reflect in life when the weld length is added to 30 for the joint steel pipe of the pipe extension joint? Plastic coated copper pipe can also produce welded pipes with different pipe diameters from billets of the same width. However, it can be compared with straight seam pipes of the same length. The rental production rate is low.

Defects in metal: various defects in the red copper strip, such as impurity atoms, vacancies, internal (grain boundary) dislocations and external surfaces cause lattice distortion and cause electron wave scattering, which affects conductivity.

The large diameter coated medical copper tube can deform to prevent the risk of ductile damage; The medical copper tube has sufficient plastic deformation, and the medical copper tube is capable of deformation. It is stipulated that the plastic deformation and ductility of medical copper tubes are good. Good plastic deformation can ensure that the structure can have significant deformation before destruction. In some peak periods of the structure, the tectonic stress will be redistributed, more kinetic energy should be digested and absorbed when the structure is destroyed, which is the risk water of ductile destruction. For the structures with plastic deformation design scheme and the structures in disaster areas, the size of the deformation working capacity of medical copper tubes has a particularly critical practical significance. 3 Production and processing characteristics of medical copper tubes. It can be integrated with cold and heat treatment, and will not cause great harm to compressive strength, plastic deformation and ductility due to such production and processing. 4 Weldability of medical copper tube. The welding of medical copper tube is a rapid heating and cooling process. The metal materials in the welding and heat affected zone need to go through heating and melting, physical reflection, cooling and crystallization, and solid state change in a very short time. The industry trend is a kind of medical copper tube. Because there is no seam in the middle, it has more advantages in strength. Medical copper tubes have many different s in practical application, and each different will make the medical copper tube work well.Advantages of medical copper tubes: compared with solid copper tubes such as round steel, medical copper tubes have the same tensile strength, torsional strength, and tensile strength, and their net weight is relatively light. One is plastic copper tubes cut for social and economic development, which are widely used in the production and processing of spare parts and mechanical parts, such as oil drilling equipment, rotating shafts, bicycle frames, and steel medical copper tube frames used in engineering construction. This kind of welded medical red copper pipe is developed under the special conditions that the temperature is all over and the composition is extremely unbalanced. After this kind of welding, it can produce detailed welding joints to maintain special performance indicators, which is the specified weldability. 5 Performance of medical copper tube. It refers to the service life of medical copper tube. The production and processing of annular parts with medical copper tubes can achieve the utilization rate of raw materials, simplify the production process, save raw materials and manufacturing hours, such as needle bearing throw rings, hydraulic jack sleeves, etc. At present, medical copper tubes have been widely used for production and processing. Disadvantages of medical copper tubes: medical copper tubes are also indispensable raw materials for various strategies. Drums must be produced and processed by medical copper tubes. Medical copper tubes can be divided into round medical copper tubes and profiled steel according to their different cross-sectional areas. Due to the large circle area under the same diameter specification, the annular pipe can be used to transport many large diameter medical copper pipes. Large diameter coated medical copper pipes are widely used in tap water, natural gas, petroleum, chemical industry, power, marine and other engineering fields. There is no solvent in the coating and no leakage, so it will not pollute the medium transported, thus ensuring the purity and hygiene of the fluid. The temperature range from - 40 ℃ to+80 ℃ can be used alternately in cold and hot cycles, without aging and cracking, so it can be used in cold areas and other harsh conditions. When processing medical copper tubes, the medical copper tube factory will use pickling, which is an indispensable part of most medical copper tubes, Pickling process is the treatment after removing surface oxide scale (Carbon steel - stainless steel - lime saponified phosphorus, butter, oil, copper and aluminum pipes - and the old ones, and then wire drawing processing. Then what are the points to be noted when washing? 1 When washing the medical copper pipes, they need to be carried out in the flowing clear water tank, so as to avoid secondary pollution. When washing, the medical copper pipes need to be fully immersed in water. At this time, the surface may be oxide and oil and it can be lifted up and down three to four times. If the medical copper tube is not acid resistant, and the phosphating solution cannot remove nuclear energy. However, after acid washing of medical copper tubes, the water in the medical copper tube needs to be cleaned to avoid water corrosion and oxidation of the medical copper tube. Therefore, it is necessary to carry out solvent treatment as soon as possible. 4 When the medical copper tube is washed, the iron salt content must be controlled within a certain range, and it cannot exceed the standard otherwise the medical copper tube may be damaged.

Mostole.The process flow of plastic coated copper pipe: the settlement price of 904l stainless steel plate is on the high side, and the price is stable. 904l stainless steel plate: last Friday, the steel plant made all the orders. As for the guide price, the end of the alloy pipe to be flared faces the flaring die, extends a certain length (depending on the flaring length), and then drives the upper clamping groove body to move down through the oil cylinder. Then, the flaring hydraulic cylinder drives the flaring die to the alloy pipe, so that the t2 copper pipe flaring die will stretch the alloy pipe port to expand its inner diameter in the alloy pipe port at the front end. The length of flared section can be 20200 mm. How to solve the crack of plastic coated copper pipe? How to solve the common fault of crack in case of improper operation during the construction of plastic coated copper pipe project? If it is not handled in time, there is a serious risk. Therefore, I will carry out practical operations in strict accordance with the engineering construction specifications and requirements related to immediacy, find more practical welding processes and then ensure the welding quality of electric welding. If we continue to develop plastic coated copper pipe materials under such circumstances, we will find that the price difference of plastic coated copper pipe with low-grade anti rust materials is different, and there are many reasons for the price difference. First, there are significant differences in production. Although it is made of stainless steel, the plastic coated copper pipe can be compared with the plastic coated copper pipe on the market.

For the production and processing of sculpted copper tubes, the sheet metal shall be first opened in the sheet metal workshop according to the dimensions shown in the drawings, which is commonly referred to as opening. Then cut the corners of these open sheets according to the height of the edge, and then use the bending machine to form the edge according to the drawing forming diagram. The shaped copper pipe shall also be installed with reinforcing ribs as required, and the four corners of the shaped plate shall be welded well. The welded parts shall be sent to the grinding workshop, and the spraying surface shall be polished and the welding interface shall be polished and leveled. The polished modeling copper pipe is then sent to the spraying workshop for processing. Before spraying, the surface of the sculpted copper pipe shall be chrome treated and the process hole shall be drilled, so as to ensure that the sculpted copper pipe can be hung on the spraying line well, and the painting can be smooth without flow marks, and the color is consistent without color difference. After that, according to customer demand, the qualified products are pasted with protective film and bound with bubble film or wooden box.

The materials of the packer shall be packed with steel strip and added according to the diameter and weight of the petroleum cracking pipe. The degreased copper pipe from the pipe can be packed without a packer. If there are wiring ports on both sides of the cracked oil pipe, external thread devices shall be provided for safety protection. Brush the nozzle with clean oil or anti rust oil. For the cracks on both sides of the petroleum cracking pipe, branch pipe safety protectors can be installed on both sides as required. If the oil cracking pipe is installed in the container, the container shall be lined with waterproof devices, the packer can weld the safety protection support frame inside the petroleum cracking tubes. Previous page: How to clean plastic coated copper tubes. What problems will be encountered when cutting plastic coated copper pipe. What problems will be encountered when cutting plastic coated copper pipe. What problems will be encountered when cutting plastic coated copper pipe. When plastic coated copper pipe is cut, the wound is uneven and cracked. Then I will introduce how to solve these problems. For the disconnection part of plastic coated copper pipe,MostoleHeat dissipation copper tube, the position and direction shall be drawn with tape or other measuring tools and the disconnection line shall be marked in combination with the construction drawing and site conditions. When the petroleum cracking pipe is disconnected, please fix the equipment with square steel pipes such as vises, and cut it after fixing. In the area to be disconnected, use a towel or soft cloth to crack the oil stain or dirt on the surface of the pipe. As we all know, if steel pipes are exposed outdoors for a long time, or there are some, they will damage the air oxide layer on the surface of the stainless steel plate, and then oxidize and rust in the cold. Gas. Therefore, the steel pipe shall be placed in the sealing area as far as possible. However, plastic coated copper tube has incomparable advantages, because its surface is not easy to be oxidized, which is the key to constitute the raw material of plastic coated copper tube. The high-precision plastic coated copper pipe has an extremely thin, firm and smooth chromium rich air oxide film on its surface to prevent oxygen molecules from re penetrating and re oxidizing in the air, thus preventing rust. The description of the plastic coated copper pipe shows that the part with weak corrosion resistance of the transition film will produce pitting corrosion reaction due to the self-excited reaction, and the small holes will form highly corrosive aqueous solution. The chloride ion content will accelerate the corrosion rate.