ShanggangT2 copper barContinue to force the roll market

Now let me talk about the damages that are easy to occur on the surface of the copper tube. In order to prevent the accumulation of process agents or products and/or dirt, scratches and other rough surfaces, mechanical cleaning must be carried out. If the copper pipe is heated to a certain high temperature in the air during welding or grinding,ShanggangCopper clad aluminum bar, chromium oxide heat return color will appear on both sides, lower surface and bottom of the weld. The color after tempering is thinner than that of the oxidation protective film, and is clearly visible. The color depends on the thickness. The thicker oxide can be found in the rainbow color, blue, purple to brown. It is usually black. It is caused by being at high temperature or being at high temperature for a long time. When any of these oxide layers exist, the chromium content on the metal surface will, and the corrosion resistance of these areas will. In this case, it is not only necessary to heat temper the color and other oxide layers, but also to clean the chromium poor metal layer under it. Free iron on the surface of t2 copper tube will rust, the powder that must float can usually be removed together with the dust. Some are very sticky and must be treated as embedded iron. In addition to dust, there are many surface iron sources, including cleaning with ordinary carbon steel wire brush and shot peening with sand, glass beads or other abrasives previously used on ordinary carbon steel, low alloy steel or cast iron, or regrinding non stainless steel products attached to copper pipe components and equipment. If there is no protection during cutting or hoisting, the wire ropes, slings and iron on the working surface can easily be embedded or dirty the surface. The copper tube shall be boiled in boiling water for 30 seconds before cold treatment. The effective internal stress is about 15%, and the residual austenite reaches the effect. Then, the second suggestion is to choose the normal treatment at minus 60 degrees, and then conduct deep cooling at minus 120 degrees. The lower the treatment temperature is, the retained austenite will be rapidly transformed into martensite, but it cannot be transformed. Through experiments, it can be found that there will be about 2% of retained austenite. At this time, retained retained austenite can achieve a certain buffer effect. After cold treatment, the air conditioning copper pipes need to be taken out and put into hot water for heating, which can effectively heat about 40% of the cold treatment stress. Tempering and cold treatment should be carried out as soon as possible after gradual heating, so as to ensure that the products will not deform in later use and facilitate daily storage. The transformation characteristics of the area of each layer of the copper tube during empty drawing affect the asymmetry of the deformation of the metal material. One of its characteristics is that the natural widening of each layer along the wall thickness is not consistent. Of course, the external layer of the copper tube is less, the internal surface layer of the copper tube is larger and the natural widening of the middle layers is slow from the external layer to the internal surface layer.The technical level of degreasing copper tube for mechanical equipment With the substantial improvement of the manufacturing level of mechanical equipment and the degree of control automation in China, there is still some gap between the technical level of domestic degreasing copper tube production line and the products of foreign counterparts. After years of reform and opening up. The quality of all aspects of degreased copper pipe has also risen by several grades, significantly narrowing the quality gap with the imported production line. The aluminum hose production line and aluminum can production line developed and produced by the company break the technological monopoly of foreign companies, can provide stable and reliable production equipment for domestic and international markets, and make great contributions to the aluminum packaging industry. With the continuous improvement of people's living standards, there will be more and more demand for degreased copper tube products, and its market potential is huge. Problems such as incomplete penetration, deformation, cracks and air holes are easy to occur during the fusion welding of degreased copper tubes. Compared with fusion welding, wood is not melted during brazing which reduces the impact of large thermal conductivity of base metal on welding quality, prevents the formation of incomplete penetration, reduces the tendency to produce pores and cracks, and ensures the performance of weld. Because the base metal is not melted, the structure and properties of the base metal are almost unchanged, so that the original service properties of the base metal can be maintained.

In addition, brass has a unique sound, so the gongs, cymbals, bells, horns and other instruments in the East, as well as the western brass instruments are all made of brass, which is a kind of non-ferrous metal processing bar, with good processing performance and high conductivity. It is mainly divided into copper tube (copper zinc alloy, cheaper). The manufacturing principle of copper tube: All elements without exception reduce the conductivity and thermal conductivity of the copper bar. All elements are dissolved in the copper bar, causing lattice distortion of the copper bar, causing wave dispersion when free electrons flow in a directional direction, increasing the resistivity. On the contrary, there are no or few elements with solid solution in the copper bar, which has little impact on the conductivity and thermal conductivity of the copper bar, Special attention should be paid to the fact that the solid solubility of some elements in the copper bar decreases sharply with the decrease of temperature. The precipitation of simple substances and metal compounds can not only strengthen the copper bar alloy by solid solution and dispersion, but also reduce the conductivity slightly. This is an important alloying principle for the study of high-strength and high conductivity alloys. Here, it should be pointed out that the alloy composed of iron, chromium and copper bar is a very important high-strength and high conductivity alloy; As the influence of alloy elements on the properties of copper bars is superposition, CoCrZr series alloys are * high-strength and high conductivity alloys; It is not easy to heat. Semi continuous casting copper tube has excellent conductivity. Copper tube has excellent conductivity. Alloy copper to ensure safety and fatigue resistance. Tin phosphor bronze jack adopts hard wire electrical structure without rivet joint or conflict contact, good elasticity and smooth dial. Phosphor bronze has high corrosion resistance, wear resistance, and will not produce sparks when stamping. It is used for medium speed and heavy load bearings. The working temperature is up to 250 ° C, and the active centering is insensitive to deflection. The bearing force is uniform, and the bearing capacity is high. It can withstand radial load and self lubrication without protection. The company is a manufacturer specializing in the production of various bronze tubes, bronze rods, bronze plates and profiled bronze profiles. Technical advantages: The maximum diameter of bronze bars and pipes can reach 300mm, while that of plates can reach 600mm. The wall thickness of bronze tube can be as small as 4mm. The copper tube is a common bronze material. The aluminum content of copper tube generally does not exceed 5%. Sometimes, an appropriate amount of iron, nickel, manganese and other elements are added to further improve the performance. It has high strength and good wear resistance. It is used for copper sleeves and wear resistant parts with high strength. The outstanding feature of t2 copper tube is its good wear resistance. The difference between copper tube and copper tube The copper tube is a copper based alloy with aluminum as the main alloy element. The copper tube is a copper based alloy with tin as the main alloy element. The mechanical properties of copper tube are higher than that of copper tube. The aluminum content of the copper tube in practical application is between 5% and 12%, the aluminum content is 5%, and the 7% copper tube has good plasticity and is suitable for cold working.

Shanggang.It mainly refers to strengthening the research on copper pipe corrosion and formulating a complete and scientific copper pipe use plan.

The price can be changed, and the transaction is affected. According to the feedback from the spot operation, the morning market transaction did not follow the temperature rise: after 9:00, the dealers took turns to raise the price, which was in disorder; Before ten o'clock, it was not as expected, and users were very cautious in purchasing; Around 11:00, the surrounding markets became loose and the price was low. High hanging, low selling, and low volume. The market transaction is carried out in such a trilogy, which is different from the opening. In this process, the mentality of traders has changed: from &turning to shipping&, it has promoted the steel mill to sell before entering their own mouth? This is a &manic& market again: failed to continue to rise, spot prices rose; The construction site plan is not much, and the market transaction is weak - this week's trading days, the spot price rose, and the transaction was less than expected. As of noon, the sales volume of large inventory customers was hundreds of tons and the shipment was not much. Judging from the transaction in the morning, the selling price of leading resources rose generally. Among the resources in Kuti, the base price of t2 copper tube was 5050 yuan/ton, and the price of earthquake resistant spiral snail was 5350 yuan; Among the resources provided by the factory, the basic price of threads of Zhongtian, Yonggang and Shagang is 5130 yuan, and the differential between spiral and t2 copper pipes is 360-380 yuan/ton. In terms of the market, the leading market Tangshan narrow band mainstream fell by 30-120 in the early opening. The overall trading situation of copper bars was weak. Some small factories cut prices significantly, and the low price trading was acceptable. Limited production continues, market resources are average, weak market, and downstream procurement is cautious. 355 is the consolidation of the medium broadband market. Today's futures continue to fluctuate. Traders are less willing to ship at low prices and have a strong mood. However, under the pressure of futures, the trading atmosphere in the spot market is not good. Copper bars continued to fluctuate in the morning, and traders were affected by multiple factors to make a small weak tone trial deal. From the commercial account, we know that there are few high market transactions, few inquiry calls, and a slightly pessimistic attitude. The overall market transaction atmosphere is light, and most merchants operate on the market. At present, the downstream demand is still low, the demand for terminal replenishment is low, and the purchasing enthusiasm is not high. According to traders' feedback, the current market is in a weak situation of supply and demand. Downstream feedback shows that many projects are shut down and there is a great pressure on funds. However, the relevant economic data and side news are too bearish, so the futures market is difficult to rebound, and the spot market is mainly responsible for the subsequent drop. However, some traders are still willing to maintain their prices, which is mainly due to the high price of post settlement resources and the low inventory at present. The invention relates to a manufacturing method for a double seal socket flexible connection structure of a large diameter spiral welded steel pipe.

.Attention shall be paid to the purchase of red copper pipe in order to study the distribution law of pipeline crack stress field under internal pressure. The simulation ysis and experimental verification are carried out for pipes with cracks of different shapes, different directions, different internal pressures and different sizes. The results show that the stress at the crack tip is much greater than that at the crack center. The crack shape has little effect on the stress. With the increase of the included angle between the crack direction and the pipe axis, the stress at the crack tip first increases and then decreases. With the increase of the pipe internal pressure, crack depth, and crack length, the stress at the crack tip increases linearly. Among them, the effect of crack length on the stress at the crack tip is smaller than that of internal pressure and crack depth. During the construction and operation of long-distance pipeline, due to the influence of pipe manufacturing defects, welding defects, stress concentration, corrosion defects and other factors, the pipeline will produce cracks and expand cracks, which is the most dangerous defect of long-distance pipeline and the main reason for pipeline failure. At present, pipeline cracks are mainly determined by internal testing and non-destructive testing after excavation. Among them, a depth of more than 1 mm in the base metal or a depth of more than 2 mm in the weld; Magnetic flux leakage internal detection has a certain detection rate for cracks with opening more than 0.25mm, but it is difficult to identify and quantify. In NDT, magnetic particle, penetration, eddy current and radiographic methods have high detection and identification rate. The generation and propagation of cracks will cause local stress concentration in the pipeline, corrosion damage and other failure phenomena fatigue damage, seriously affecting the service performance and reliability of long-distance pipeline. In this paper, the influence of crack shape, direction and size on the stress at the crack tip is yzed by studying the stress field distribution law of copper pipe cracks, which provides a reference for the prevention and control of pipe cracks. What problems will be encountered in the production of copper tubes. The production of copper pipe includes four steps: welding, forming, inspection and pipe expansion.

However for some important parts, it is also considered that the yield ratio should be smaller to improve their safety and reliability. However, at this time, the utilization rate of materials is also low. Common sense: copper pipes for air conditioners are mainly used for conveying liquid, gas and steam; Boiler pipes and steam transmission pipes are used for the piping, structure and steam transmission of steam boilers, including the transmission of high-temperature and high-pressure steam; Structural pipe, widely used in aviation automobile, tractor and other industrial sectors; Pipe for petroleum industry, mainly used for oil and gas exploitation, such as casing, drill pipe and tubing, and pipe for petroleum refining and processing; Pipe for mechanical manufacturing, which is used to manufacture the race of ball bearing, the plunger, rotating shaft and body of air pump and hydraulic pump; High pressure vessel, etc. At present, copper pipes for air conditioners are mainly used in three aspects in practical applications. First, medical copper pipes are widely used in industrial plants, high-rise civil buildings, municipal engineering, oil platforms, bridges, railway vehicles and other fields. Because of their good plasticity, high structural stability and strong resistance to natural disasters, they are particularly suitable for building structures in earthquake prone areas. Second, the air conditioning copper pipe has high tensile strength and toughness, high buildings, bridges and other steel structures have good cold bending performance and welding performance, so it is widely used in vehicle manufacturing, large bridge construction, mechanical manufacturing, industrial plant components and many other industries. Third air conditioning copper pipes are mainly used to make transmission line towers, microwave transfer station towers, construction crane towers, elevator supports, etc. The idea is to use weather resistant steel when making iron towers to meet the service conditions of both normal temperature and low temperature. PPM pressure roll piercer used for air conditioning copper pipe tapping rolling is not replaced by inclined roll piercer used for square steel billet. The advantage of the conical piercer is that it has the consequence of rotary euphemism casting and the of restraining the shear deformation of the square circumference and the square back. Therefore, it can prevent the defects outside the steel pipe. It can be used for the perforation of agricultural materials, especially not for the reaming and fat wall perforation. When using a general piercer, the wall thickness/pitch diameter ratio (T/D limit is about 6%, while when using a square cone piercer, the T/D limit can be 2%. Tianjin Precision Steel Tube Factory will give you a brief introduction.

Use the medical copper tube table to eat. Because of the unique of the medical copper tube, when the oil drops on the table, it will only stick to the table, but not penetrate the table. Only with a slight wipe of the rag, the oil stains will be easily disappeared. In this case, when cleaning large canteens, the liquidators do not need to spend much effort but are relaxed. They just need to prepare a rag and a basin of clean water, and its exterior is not made of the medical copper tube. The price is cheaper than the wooden table, which is extremely suitable for a small amount of purchase. The medical copper tube has a natural bright and beautiful feeling. The color is extremely blended, and can stop the very good embellishment and reaction with the color in the surrounding situations. Now, let's understand some STEPs of the appearance processing of medical copper tubes. There are about five different methods for the appearance processing of medical copper tubes. Connect to t2 Medical Copper Tube Company and introduce them to the master. In addition, these methods can also stop the combined processing and create more medical copper tubes with different appearances. No matter which method is used, the following STEPs should be followed. First, before processing, the agreement should be stopped with the manufacturer and then a sample should be selected as the standard for future consumption. The second part, when using it, we should guarantee that the coils of the base we choose to use and the coils that are not yet used are the third of the same model and batch. If they are used in some construction, such as elevators, we should pay attention to the unexpected selection of materials. In some places with extraordinary contrast, it is not appropriate to use the mirror t2 medical copper tubes. When processing, it is necessary to select the appropriate manufacturing process, such as weld grinding, how to restore the appearance. Class For the processing of the appearance of some textured t2 medical copper tubes, which is also called unidirectionality. For example if the lines used are vertical rather than horizontal, it is not easy to apply the dirty residue on the appearance of t2 medical copper tubes. It is extremely easy when they are clean. When finishing, STEP of the process used should be added, so the cost also needs to be added. Therefore, when selecting the appearance of the processing, t2 Medical Copper Tube Company revealed that Panbo consumers should carefully select according to the situation, and when selecting the planning and design staff, they should have a full understanding of the appearance of t2 Medical Copper Tube. Since the birth of medical copper tube, it has been widely used in food, chemical industry, crude oil, machine manufacturing and other industries for its superior . It is precisely because of this kind of universal needs that people are increasingly demanding for medical copper tubes. Although this kind of situation is basically conducive to the development of the medical copper tube industry. Having said so much, the editor of this website will introduce the most popular technology in the medical copper tube industry -- the medical copper tube appearance fingerprint free disposal punishment technology. Mentioned here, I believe that many enemies have learned the greatest advantages of this kind of technology from the name. However, do you know that this is nothing more than a contrast of significant and abstract advantages. The most one-sided introduction is also my face. The medical copper tube after adopting this kind of technical treatment has a smooth appearance and soft hand feeling, and ordinary dust and impurities are not easy to adhere. Therefore, just wipe it with a wet rag and you will lose the clean and smooth appearance. Because the implementation of this kind of craft is to use electroplating oil to shine the film on the red interior line, so it has the characteristics of being tough and not easily scratched. This prevents the possibility that some slight bumps may damage the medical copper tube. It also allows the medical copper tube to be used twice as quickly. Stop the fingerprint free disposal and punish the medical copper tube after the accident. It also loses great promotion in appearance. As the saying goes, a superior appearance can always leave the best impression. Therefore, compared with the medical copper tube after the punishment and the medical copper tube without the punishment, it can often be welcomed by customers and enemies.Hot rolling and hot expansion. The main processing procedures include the blank sawing process, and the production process of the air conditioning copper pipe in the tower mainly includes cold drawing. Ring furnace heating process, pipe rolling process, sizing process, cooling bed process, straightening process, pipe cutting soot blowing process, magnetic flux leakage detection process, surface inspection length measurement and weighing to packaging and warehousing. Key points: yield strength limit: when the external force borne by the air conditioning copper tube sample exceeds the elastic limit of the material, although the stress no longer increases, the sample still has obvious plastic deformation. This phenomenon is called yield, that is, when the material bears an external force to a certain extent, its deformation is no longer in direct proportion to the external force, resulting in obvious plastic deformation. The stress when the air conditioning copper pipe yields is called the yield strength limit, there will be an obvious yield point on the tensile curve, while for materials with low plasticity, there will be no obvious yield point, so it is difficult to calculate the yield limit according to the external force at the yield point. Therefore, expressed as 0. The yield limit index can be used as the design basis for requiring that the parts do not produce obvious plastic deformation during operation.

The operation is very convenient. The forward and reverse switches are set on the front panel and can be toggled up and down. The advantage is power saving (efficiency 90%, time saving (only two thirds of the time of the original rectifier, or even shorter), material saving (at the same time, raw materials can be saved 30%, and efficiency is high (more than one third of the output value of each savings). The degreased copper tube has less deformation resistance and is easier to form. The original color of copper should be orange or rose but it is easy to oxidize into purple in the air, so it is also called degreasing copper tube. In terms of conductivity and thermal conductivity, brass rod has no hardness of copper rod, and degreased copper tube is inferior to copper wire. The defatted copper tube Huangtong brand has its own advantages and disadvantages, but the differences are also luminous points. Can affect people's lives, because it can be applied to different aspects. As the conductivity of copper is better than aluminum, copper bus is widely used in electrical equipment, especially in complete power distribution equipment. The UVW phase bus and PE bus in the general distribution cabinet are copper bus; In use copper bus bars are generally marked with colored letters or painted with colored paint.

Remove the flame. If the filler metal does not melt, continue to heat the joint and try again. The melted filler metal is sucked into the casing port according to the capillary effect until a complete filler metal ring appears on the casing port. Remove the flame Pay special attention not to let the flame directly contact the filler metal. It should be the heat at the joint that melts the filler metal. In order to clean the copper pipe, the welding flux must have a degree of corrosivity, and shall be cleaned after brazing. The so-called &self-cleaning& fluxes are generally not recommended because of their corrosivity.

The process flow of plastic coated copper pipe: the settlement price of 904l stainless steel plate is on the high side, and the price is stable. 904l stainless steel plate: last Friday, the steel plant made all the orders. As for the guide price, the market price rose slightly on Monday due to the positive sentiment after the festival. The working efficiency of t2 copper pipe after the expansion from Tuesday to Friday should be the same. Between the upper and lower clamping groove bodies of the alloy pipe to be flared, the end of the alloy pipe to be flared faces the flaring die, extends a certain length (depending on the flaring length), and then drives the upper clamping groove body to move down through the oil cylinder. Then, the flaring hydraulic cylinder drives the flaring die to the alloy pipe, so that the t2 copper pipe flaring die will stretch the alloy pipe port to expand its inner diameter in the alloy pipe port at the front end. The length of flared section can be 20200 mm. How to solve the crack of plastic coated copper pipe? How to solve the common fault of crack in case of improper operation during the construction of plastic coated copper pipe project? If it is not handled in time, there is a serious risk. Therefore, I will carry out practical operations in strict accordance with the engineering construction specifications and requirements related to immediacy, find more practical welding processes and then ensure the welding quality of electric welding. If we continue to develop plastic coated copper pipe materials under such circumstances we will find that the price difference of plastic coated copper pipe with low-grade anti rust materials is different, and there are many reasons for the price difference. First, there are significant differences in production. Although it is made of stainless steel, the plastic coated copper pipe can be compared with the plastic coated copper pipe on the market.

Pursuit of excellence.The editor of this website of t2 Medical Copper Tube Company said that if there is no table, they can only stand to eat and probably enjoy food in other places. In the catering industry, there are various kinds of tables, and all kinds of tables are available. There are wooden tables and medical copper controlled tables. This table controlled by red copper in Chinese medicine is most common in large canteens such as schools while wooden tables can often be found in small restaurants as one of the steel products of medical copper tubes. As his name is common, medical copper tubes have the ability to prevent rust. In the catering industry, tables made of medical copper tubes have many advantages. Next, the teacher of Medical Copper Tube Consumption Co., Ltd. will introduce you to the master. The medical copper tube table is easy to see in the large canteen. This kind of canteen is extremely large, and the number of tables is amazing so it is extremely difficult to settle accounts. If a wooden table is used, it will cost a lot of money,ShanggangRed copper bar, and it will also take a lot of work to settle after eating.

The demand for t2 copper tubes is increasing. At the same time, in the market, the quality identification method of t2 copper tube for grid fittings is currently accompanied by rapid economic development. There are many kinds of sales, different purposes and different quality. Therefore, when purchasing, you should be clear and have certain selection skills. Here we introduce the quality identification method of t2 copper tube. The color of t2 copper tube depends on the color of t2 copper tube. Although the external color is a visible factor, the color of the product is closely related to its production process and quality control. If the product is bright in color and high in glossiness, it is generally superior to the product with poor color. The t2 copper tube with uniform thickness should be selected. Because some small manufacturers are limited in technology and process, it is difficult to ensure that the product thickness is uniform and neat. Therefore, the thickness is also an important factor to test the quality of the pattern plate. Later, the casting process of t2 copper tube.

No heating and plating bath is required. The process is simple and easy to operate. The cold drawn degreased copper tube bright tin plating is one of the anti discoloration mirror bright brush tin plating and degreased copper tube tin plating mean copper bar partial or overall tin plating.

Handle carefully to prevent damage and scratches. 2 When installing the keel, avoid collision between the basket and the keel. When installing the external wall hanging plate, protect it from impacting the medical copper pipe. 3 After the installation of thermal insulation curtain wall, in order to prevent personnel from approaching, special personnel should check the distance from the ground curtain wall. 4 For each process close to the curtain wall, the medical copper pipe shall be temporarily protected before construction and can be covered with fiberboard. Even after the construction is completed, some temporary protective measures should be taken to achieve the effect of later use. 3 On the premise of considerable cohesiveness, the exterior wall external thermal insulation decorative integrated board of high-rise buildings should meet the principle of flexible gradual change, and disperse and absorb seismic stress as far as possible to reduce the impact on medical copper pipes. 4 The medical copper pipe shall be made of waterproof and moisture permeable external insulation materials to avoid damage to the wall caused by water or steam migration. 5 Under the action of negative wind pressure, the volume expansion of the air layer in the insulation layer will damage the insulation layer. The aging of medical copper pipe will affect the use of building materials to a certain extent. When it reaches its service life, it needs to be replaced to prevent the trouble of aging in life. 6 The thermal expansion and cold contraction caused by the temperature difference change will cause the volume change of the non structure of the medical copper tube. Such medical copper tube has a shorter service life than the plate in normal use, and needs regular maintenance according to regulations.

Development Curriculum.It is applicable to the removal of thin liquid oil stain and light rust and the generation of phosphating film with certain corrosion resistance. See Table 3 for example of formula and operating conditions. Table 3 Degreasing, rust removal, phosphating and passivation

The price of tube billets was adjusted and lowered mainly due to the production restriction of environmental protection and the weak demand for temperature and weather. Recently, the terminal demand has also shrunk due to the sudden drop in temperature, causing a weak shock. According to the communication with local traders in Cangzhou, various good news last week led to the shipment of thermal expansion pipes in Cangzhou in the past two weeks, which is better in the off-season, and the shipment of some specifications has improved. However, the trading atmosphere in the small and medium-sized pipe market is still cold, and the demand is slowing down gradually. To sum up, it is expected that the market price of Cangzhou seamless pipe will be stable and weak in the near future.

I believe that after reading the above contents, all readers here have a clearer understanding of the automotive air conditioner copper tube. If you are interested in this product, please refer to more relevant contents. Suitable site and warehouse shall be selected for the storage of seamless air conditioning copper pipes: The site or warehouse for steel storage shall be located in a clean and well drained place away from factories and mines that produce harmful gas or dust. With the rapid development of economy, the number of cars is also fast. Nowadays, people can't live without cars. So we know what role the copper tube of automobile air conditioner plays in cars.

Shanggang.What problems should we pay attention to in each production. It is a key process to weld copper pipe with correct process. Welding materials, welding speed of t2 copper pipe,Shanggang321 stainless steel round steel, welding current, welding voltage, wire arrangement, spacing, inclination and other process parameters will affect the performance of the weld. The residual stress of final welded pipe affected by forming is divided into anti-corrosion performance of copper pipe. Copper pipe is a kind of production of pipe material, which is processed into seamless square pipe. The physical properties of copper tubes are slightly weaker than those of hot-rolled steel tubes. The copper tube adopts a two-step push tube expanding machine, which integrates cone die tube expansion, data medium frequency induction heating and hydraulic press. With effective processing technology, low energy consumption less infrastructure construction, good products, wide application fields of raw materials and products, and what are the production batches suitable for copper tube testing. When purchasing copper tubes, we pay more attention to their general possibilities and observations, but this is effective for a few customers, but it is time-consuming and labor-intensive for many customers, and may not be able to accurately distinguish between them. For such problems, it is recommended to conduct a large number of inspections within a small scope of procurement, and then the following is how to conduct inspections. The dimension tolerance of the cleanliness and wall thickness of the inner cavity of the copper tube is strict. However, in the whole process of electric welding, due to the role of the molten metal material of the air conditioning copper pipe, the thickness of the pipe at the welding point will be uneven, and the inside and outside of the welding will be uneven. This will cause energy consumption of the conveyor. At this time the internal welding ground must be used for leveling. Next, we will take you to the production process of copper pipe - internal welding and calibration. At present, many materials are also used in the life of red copper pipes. Be as judgmental as possible when buying. In fact, there are many things to pay attention to when purchasing copper tubes. Want to keep high when buying. What should we pay attention to when buying copper tubes next. The daily use and market are calculated according to the weight, so you should decide how much to use before buying.

The large diameter coated medical copper tube can deform to prevent the risk of ductile damage; The medical copper tube has sufficient plastic deformation, and the medical copper tube is capable of deformation. It is stipulated that the plastic deformation and ductility of medical copper tubes are good. Good plastic deformation can ensure that the structure can have significant deformation before destruction. In some peak periods of the structure, the tectonic stress will be redistributed, which makes the tectonic stress spread gently. Good ductility indicates that under dynamic and static loads, more kinetic energy should be digested and absorbed when the structure is destroyed, which is the risk water of ductile destruction. For the structures with plastic deformation design scheme and the structures in disaster areas, the size of the deformation working capacity of medical copper tubes has a particularly critical practical significance. 3 Production and processing characteristics of medical copper tubes. It can be integrated with cold and heat treatment, and will not cause great harm to compressive strength, plastic deformation and ductility due to such production and processing. 4 Weldability of medical copper tube. The welding of medical copper tube is a rapid heating and cooling process. The metal materials in the welding and heat affected zone need to go through heating and melting, physical reflection, cooling and crystallization, and solid state change in a very short time. The industry trend is a kind of medical copper tube. Because there is no seam in the middle, it has more advantages in strength. Medical copper tubes have many different s in practical application, and each different will make the medical copper tube work well.Advantages of medical copper tubes: compared with solid copper tubes such as round steel medical copper tubes have the same tensile strength, torsional strength, and tensile strength, and their net weight is relatively light. One is plastic copper tubes cut for social and economic development, which are widely used in the production and processing of spare parts and mechanical parts, rotating shafts, bicycle frames, and steel medical copper tube frames used in engineering construction. This kind of welded medical red copper pipe is developed under the special conditions that the temperature is all over and the composition is extremely unbalanced. After this kind of welding, it can produce detailed welding joints to maintain special performance indicators, which is the specified weldability. 5 Performance of medical copper tube. It refers to the service life of medical copper tube. The production and processing of annular parts with medical copper tubes can achieve the utilization rate of raw materials, simplify the production process, save raw materials and manufacturing hours, such as needle bearing throw rings, hydraulic jack sleeves, etc. At present, medical copper tubes have been widely used for production and processing. Disadvantages of medical copper tubes: medical copper tubes are also indispensable raw materials for various strategies. Drums must be produced and processed by medical copper tubes. Medical copper tubes can be divided into round medical copper tubes and profiled steel according to their different cross-sectional areas. Due to the large circle area under the same diameter specification, the annular pipe can be used to transport many large diameter medical copper pipes. Large diameter coated medical copper pipes are widely used in tap water, natural gas, petroleum, chemical industry, power, marine and other engineering fields. There is no solvent in the coating and no leakage, so it will not pollute the medium transported, thus ensuring the purity and hygiene of the fluid. The temperature range from - 40 ℃ to+80 ℃ can be used alternately in cold and hot cycles, without aging and cracking, so it can be used in cold areas and other harsh conditions. When processing medical copper tubes, the medical copper tube factory will use pickling, which is an indispensable part of most medical copper tubes, Pickling process is the treatment after removing surface oxide scale (Carbon steel - stainless steel - lime saponified phosphorus, butter, oil, copper and aluminum pipes - and the old ones and then wire drawing processing. Then what are the points to be noted when washing? 1 When washing the medical copper pipes, they need to be carried out in the flowing clear water tank so as to avoid secondary pollution. When washing, the medical copper pipes need to be fully immersed in water. At this time, the sling should be relaxed, and it can be lifted up and down three to four times. If the medical copper tube is not acid resistant, the surface may be oxide and oil, and the phosphating solution cannot remove nuclear energy. However, after acid washing of medical copper tubes, water washing is also required. 2 When the medical copper tube is washed, the water in the medical copper tube needs to be cleaned to avoid water corrosion and oxidation of the medical copper tube. Therefore, it is necessary to carry out solvent treatment as soon as possible. 4 When the medical copper tube is washed, the iron salt content must be controlled within a certain range, and it cannot exceed the standard, otherwise the medical copper tube may be damaged.

In future work, try to protect the surface of the copper tube.