Bayan honger316L stainless steel plateJudgment and coordination

However, for some important parts, it is also considered that the yield ratio should be smaller to improve their safety and reliability. However, at this time, the utilization rate of materials is also low. Common sense: copper pipes for air conditioners are mainly used for conveying liquid, gas and steam; Boiler pipes and steam transmission pipes are used for the piping, structure and steam transmission of steam boilers, including the transmission of high-temperature and high-pressure steam; Structural pipe, widely used in aviation, automobile, tractor and other industrial sectors; Pipe for petroleum industry, mainly used for oil and gas exploitation, drill pipe and tubing, and pipe for petroleum refining and processing; Pipe for mechanical manufacturing, which is used to manufacture the race of ball bearing, the plunger, rotating shaft and body of air pump and hydraulic pump; High pressure vessel, used for manufacturing bottles, boilers, shells, etc. At present, copper pipes for air conditioners are mainly used in three aspects in practical applications. First, medical copper pipes are widely used in industrial plants, high-rise civil buildings, municipal engineering, oil platforms, bridges, railway vehicles and other fields. Because of their good plasticity, high structural stability and strong resistance to natural disasters, they are particularly suitable for building structures in earthquake prone areas. Second, the air conditioning copper pipe has high tensile strength and toughness, high buildings, bridges and other steel structures have good cold bending performance and welding performance, and the section size and surface quality are well controlled, large bridge construction mechanical manufacturing, industrial plant components and many other industries. Third, air conditioning copper pipes are mainly used to make transmission line towers, microwave transfer station towers, construction crane towers, elevator supports, etc. The idea is to use weather resistant steel when making iron towers to meet the service conditions of both normal temperature and low temperature. PPM pressure roll piercer used for air conditioning copper pipe tapping rolling is not replaced by inclined roll piercer used for square steel billet. The advantage of the conical piercer is that it has the consequence of rotary euphemism casting and the of restraining the shear deformation of the square circumference and the square back. Therefore, it can prevent the defects outside the steel pipe. It can be used for the perforation of agricultural materials, especially not for the reaming and fat wall perforation. When using a general piercer, the wall thickness/pitch diameter ratio (T/D limit is about 6%, while when using a square cone piercer, the T/D limit can be 2%. Tianjin Precision Steel Tube Factory will give you a brief introduction.

Manufacture gear, shaft sleeve, worm gear and other high-strength wear-resistant parts and high corrosion resistance elastic components. Key points of semi continuous casting process for copper tube: The copper tube has strong air absorption, easy oxidation and slag formation, large solidification shrinkage, poor thermal conductivity and other casting properties, and poor casting performance; Before casting, some alkaline earth metal compounds, such as Na3A lF6 and NaF mixture, are used as slag removers to purify the copper liquid, which is effective for improving the purity of liquid metals and the crystal structure of ingots. The pouring temperature of copper pipes is generally 1120~1180 ℃, and the pouring temperature of large-sized ingots is generally lower. The casting speed of the copper tube is low, and the metal level in the mold can be cast in an open flow manner without any protection; The melt needs to enter the mold through the hole at the bottom of the funnel. The design of funnel aperture should meet two conditions at the same time: one is to ensure the flow matching the casting speed; Second, ensure that the liquid level in the funnel is always kept at a certain height, so that the scum on the liquid level cannot flow into the crystallizer from the funnel hole; The copper tube ingot is easy to produce air holes and concentrated shrinkage cavities. At the end of pouring, the joint coating must be carefully carried out to avoid concentrated shrinkage cavities in the ingot. The red copper tube is a bar shaped object made of copper and zinc alloy, named after its yellow color. Copper content is 56%~68% brass, and its melting point is 934967 degrees. Brass has good mechanical properties and wear resistance, and can be used to manufacture precision instruments, ship parts, gun casings, etc. Different zinc content also has different colors. For example, when the zinc content is 18%, 20% will be red and yellow, while when the zinc content is 20%, 30% will be brown and yellow.

Bayan honger.The material of the water separator is the same, the expansion coefficient is the same, and the connection with the water separator is not easy to leak. Scope of application: As the copper pipe is more expensive than the plastic pipe, the cost of the floor heating system is higher.

For the production and processing of sculpted copper tubes, the sheet metal shall be first opened in the sheet metal workshop according to the dimensions shown in the drawings, which is commonly referred to as opening. Then cut the corners of these open sheets according to the height of the edge, and then use the bending machine to form the edge according to the drawing forming diagram. The shaped copper pipe shall also be installed with reinforcing ribs as required, and the four corners of the shaped plate shall be welded well. The welded parts shall be sent to the grinding workshop, and the spraying surface shall be polished and the welding interface shall be polished and leveled. The polished modeling copper pipe is then sent to the spraying workshop for processing. Before spraying, the surface of the sculpted copper pipe shall be chrome treated and the process hole shall be drilled, so as to ensure that the sculpted copper pipe can be hung on the spraying line well, and the painting can be smooth without flow marks, and the color is consistent without color difference. After that, according to customer demand, the qualified products are pasted with protective film and bound with bubble film or wooden box.

.In particular, it is an improved spray type passivation box for t2 copper pipe production line. The installation step of the connection structure 100 between t2 copper pipe and aluminum bar belongs to the improvement of the spray type passivation box structure for t2 copper pipe production line. The passivation solution spray box is set above the side of the passivation solution box, the passivation solution spray box with downward sloping bottom is connected with the inlet of the passivation solution box by the outlet set on the box wall at the bottom of the inclined bottom, the inlet of the passivation solution box is located on the box wall above the passivation solution box, the upper side of the passivation solution box is installed with a passivation pump, and the inlet pipe of the passivation pump is connected with the passivation solution box, The outlet pipe of the passivation pump is connected with the upper port of the passivation liquid spray box. With reasonable structure and convenient operation, it is convenient for operators to add passivation liquid to the passivation box, clean colloidal crystals at the bottom of the passivation box, avoid equipment blockage, avoid crystals adhering to the zinc layer on the surface of galvanized pipe, and improve the surface quality of galvanized steel pipe.

The material cost of medical copper tube will not be less than 40 yuan. The better the material is, the higher the price will be. It is called &one cent, one cent&. Moreover, in addition to the production and operation costs, labor costs, factory rent, etc., you must pay attention to the quotation below 45 yuan/square. Medical copper tubes are more and more widely used in the decoration of building exterior walls. In cold cities in the north, medical copper tubes can play a very good role in decoration and insulation. With the continuous progress of science and technology, the quality and firmness of medical copper tubes have been improved. However as long as the decoration materials are used, they will inevitably crack during installation and construction. As time goes by, there will be aging to varying degrees in daily life. Next, Zhongsheng Thermal Insulation Technology will introduce how to prevent the cracking of medical copper tubes and how to prevent the aging of medical t2 copper tubes? Let's talk about these two issues. How to prevent cracking of medical copper pipes To avoid cracks, buildings should be fully insulated, including awnings and other components. Through the quality and construction methods of external medical copper pipes, the construction quality can reach By reducing the ratio of the linear expansion coefficient of external thermal insulation materials of the building structure to the linear expansion coefficient of materials such as external decoration leveling mortar and external decoration surface, gradual changes will occur between medical copper pipes layer by layer, To prevent cracking. How to prevent medical copper tube from aging? The insulation layer of high-rise buildings shall have fire resistance , and shall have the characteristics of preventing fire spread and releasing smoke or toxic gas in case of fire. The strength and volume of materials shall not be reduced too much, and the surface shall not burst or collapse. Medical copper tube Medical copper tube is a new type of plate which is popular in China in recent years. It has many advantages, such as good heat preservation, fire insulation, sound insulation, convenient construction, beautiful appearance, etc., and is deeply welcomed by the industry. The medical copper pipe may fall during use. In order to reduce the occurrence of this kind of phenomenon, Jinan Zhongsheng Thermal Insulation Technology made a detailed ysis. Next, we will introduce the reasons for the fall of the external wall of the medical copper pipe and how to protect the medical copper pipe during installation. Reasons for the fall of the external wall of the medical copper pipe The medical copper pipe was not firmly fixed and moved, forming a push-pull effect, causing local hollowing of the insulation layer, and long-term water seepage after cracks, leading to the fall of the insulation layer. 3 At the connection between the concrete beam column and the masonry, the medical copper pipe is easy to fall off due to the deformation of the masonry. 4 Scaffold holes are not solid, forming insulation layer, and local base course is not firm and damaged. 5 The surface load of the medical copper tube is too large, or the anti negative wind pressure measures are unreasonable.

I believe that after reading the above contents, all readers here have a clearer understanding of the automotive air conditioner copper tube. If you are interested in this product, please refer to more relevant contents. Suitable site and warehouse shall be selected for the storage of seamless air conditioning copper pipes: The site or warehouse for steel storage shall be located in a clean and well drained place away from factories and mines that produce harmful gas or dust. With the rapid development of economy, the number of cars is also fast. Nowadays people can't live without cars. So we know what role the copper tube of automobile air conditioner plays in cars.

However, adhere to the wear form condition simulation criteria of the sample test select PVD chromium nitride ring and molybdenum spraying ring as the matching materials for the plastic coated copper pipe which can operate without fault for a long time even if it is opened or closed. Target There will be no sharp decline in the price of copper tubes in Linyi at the end of the month. The price of plastic coated copper pipe will continue. Pop up the position line and line it may cause recoverable temporary damage to people who have been away from these radioactive sources for a long time. The DC brushless motor with small volume and large power is adopted, use the self-developed opposed reciprocating wear tester, carry out the load level test, wear test, lean oil test, and research the load. As for the corrugated process of the finished plastic coated copper pipe as claimed in claim 1, the radiation source for the engineering design of the integrated rigid flexible connection plastic coated copper pipe belongs to the low hazard source. Basically, it will not cause artificial damage. The basic principle of the foundation of the integral rigid flexible connection plastic coated copper pipe sluice discussed the influence of process parameters and heat treatment process on the microstructure phase distribution and mechanical properties of the alloy, and obtained some important research results. The number of joints of steel pipes and plastic coated copper pipes on the same section shall not exceed 50% of the number of pipes. Before installation, the pipe shed shall sweep and clean the hole with drill bit or high-pressure air, and the scum in the hole shall be removed, Ensure the aperture (The hole diameter shall not be less than 127cm, and the hole depth shall meet the requirements to prevent hole plugging. Most of the seamless steel pipes produced now are hot-rolled. Because of the high temperature, the deformation resistance is relatively small and generally the steel plate is used for rolling. In this operation, the detailed thickness of the steel plate shall also be considered. If it is about the harmful elements with relatively low accuracy requirements, plastic coated copper pipes must be required. The pipe shed can be installed, extended section by section, and What does plastic coated copper pipe with a diameter of 1 reflect in life when the weld length is added to 30 for the joint steel pipe of the pipe extension joint? Plastic coated copper pipe can also produce welded pipes with different pipe diameters from billets of the same width. However, it can be compared with straight seam pipes of the same length. The rental production rate is low.

It mainly refers to strengthening the research on copper pipe corrosion and formulating a complete and scientific copper pipe use plan.

In addition, brass has a unique sound, so the gongs, cymbals, bells, horns and other instruments in the East, as well as the western brass instruments are all made of brass, which is a kind of non-ferrous metal processing bar, with good processing performance and high conductivity. It is mainly divided into copper tube (copper zinc alloy, cheaper). The manufacturing principle of copper tube: All elements without exception reduce the conductivity and thermal conductivity of the copper bar. All elements are dissolved in the copper bar, causing lattice distortion of the copper bar, causing wave dispersion when free electrons flow in a directional direction, increasing the resistivity. On the contrary, there are no or few elements with solid solution in the copper bar, Special attention should be paid to the fact that the solid solubility of some elements in the copper bar decreases sharply with the decrease of temperature. The precipitation of simple substances and metal compounds can not only strengthen the copper bar alloy by solid solution and dispersion, but also reduce the conductivity slightly. This is an important alloying principle for the study of high-strength and high conductivity alloys. Here it should be pointed out that the alloy composed of iron, silicon, chromium and copper bar is a very important high-strength and high conductivity alloy; As the influence of alloy elements on the properties of copper bars is superposition, CoCrZr series alloys are * high-strength and high conductivity alloys; It is not easy to heat. Semi continuous casting copper tube has excellent conductivity. Copper tube has excellent conductivity. Alloy copper to ensure safety and fatigue resistance. Tin phosphor bronze jack adopts hard wire electrical structure without rivet joint or conflict contact, which can ensure excellent touch, good elasticity and smooth dial. Phosphor bronze has high corrosion resistance, wear resistance, and will not produce sparks when stamping. It is used for medium speed and heavy load bearings. The working temperature is up to 250 ° C, and the active centering is insensitive to deflection. The bearing force is uniform, and the bearing capacity is high. It can withstand radial load and self lubrication without protection. The company is a manufacturer specializing in the production of various bronze tubes, bronze rods, bronze plates and profiled bronze profiles. Technical advantages: The maximum diameter of bronze bars and pipes can reach 300mm, while that of plates can reach 600mm. The wall thickness of bronze tube can be as small as 4mm. The copper tube is a common bronze material. The aluminum content of copper tube generally does not exceed 5%. Sometimes, an appropriate amount of iron, nickel, manganese and other elements are added to further improve the performance. It has high strength and good wear resistance. It is used for copper sleeves and wear resistant parts with high strength. The outstanding feature of t2 copper tube is its good wear resistance. The difference between copper tube and copper tube The copper tube is a copper based alloy with aluminum as the main alloy element. The copper tube is a copper based alloy with tin as the main alloy element. The mechanical properties of copper tube are higher than that of copper tube. The aluminum content of the copper tube in practical application is between 5% and 12%, the aluminum content is 5%, and the 7% copper tube has good plasticity and is suitable for cold working.

retailer.The degreased copper tube is made of oxygen free copper rod, bent and other process design requirements. The surface can be subject to anti-corrosion treatment, such as nickel plating, tin plating, zinc plating, etc. The surface anti-corrosion can reach 72 hours of fog test. The surface tin plating is environment-friendly lead-free tin, and the surface tin layer supports soldering. T2 degreased copper tube is mainly used for communication cabinet, transformer, charging pile, box type substation and other electrical facilities. The copper bar is harder than the plastic pipe and has the degree of common metal (the strength of the cold drawn degreased copper pipe is equivalent to that of the steel pipe with the same wall thickness). It is not easy to corrode and is resistant to high temperature and high pressure. It can be used in various applications. The main material of copper bar is copper. The melting point of copper is as high as 1083 ℃, and the temperature of hot water can be ignored for degreased copper pipe, so as long as it is used correctly, there is no need to worry about safety. When choosing to decorate the house, few people ask about the water supply pipe of the house. In fact,Bayan hongerAluminum row of cold storage, the material of water supply pipeline will greatly affect people's health. T2 copper tube has strong capacity. Escherichia coli in the water supply will not continue to breed in the degreased copper tube, and copper ions have a strong ability. Copper and zinc plating can avoid rusting and show a zinc protective film to metal materials. The conductive metal material repair and color enhancement care agent I can generate the thickness of the metal material epoxy protection layer and the pipeline cathodic protection layer, which can resist extreme weather and is suitable for the long-term surface of metal materials. The actual effect of salt and water corrosion resistance is good. The copper bar tin plating can prevent the air oxidation of the copper bar and the connection surface of the copper bar. In addition, the melting of metal tin and copper will produce aluminum alloy which will improve the adhesion of copper strip coating. In addition, and also prevent copper from oxidizing/sulfurizing and blackening and affecting electricity. The service life of the tinned copper tube is several times or even more than ten times the conductivity of metal tin is good. The purpose of copper and tin plating: effectively prevent copper from becoming verdant due to moisture, which greatly increases the service life of the copper and plays a considerable role in protecting the copper. The of tinned metal surface treatment on copper bar is to avoid air oxidation. As the air in industrial production air, the copper bar surface shall be tinned for the total area, the demand for plastic coated copper tubes is gradually increasing. Then how to apply wood grain paint on alloy pipes. Wood like paint is a kind of wood like paint. It is used for spraying plastic coated copper pipe and its process flow. Plastic coated copper pipe is mainly used to manufacture high-pressure alloy pipe for heating surface of water tube boiler with high pressure and above. In the morning market, and the tax inclusive base price quoted by Hongwang and Chengde was 8070-8150 yuan/ton. On a month on month basis, and the mainstream tax inclusive base price in the market changed from strong to weak in the 7900-8100 plastic coated copper pipe supply and demand relationship. It was difficult for the price of plastic coated copper pipe in the Guangzhou market to fall sharply this week. Second, plastic coated copper tubes are widely used in superheaters, headers and main steam ducts of domestic HP, UHP and subcritical power plant boilers. Third, large diameter pipes are mainly used as headers and main steam pipes with steam parameters below 565 ℃.

Attention shall be paid to the purchase of red copper pipe in order to study the distribution law of pipeline crack stress field under internal pressure. The simulation ysis and experimental verification are carried out for pipes with cracks of different shapes, different directions, different internal pressures and different sizes. The results show that the stress at the crack tip is much greater than that at the crack center. The crack shape has little effect on the stress. With the increase of the included angle between the crack direction and the pipe axis, the stress at the crack tip first increases and then decreases. With the increase of the pipe internal pressure, crack depth, and crack length, the stress at the crack tip increases linearly. Among them, the effect of crack length on the stress at the crack tip is smaller than that of internal pressure and crack depth. During the construction and operation of long-distance pipeline,Bayan honger7075 aluminum pipe, due to the influence of pipe manufacturing defects, welding defects, internal and external loads, stress concentration, corrosion defects and other factors, the pipeline will produce cracks and expand cracks, which is the most dangerous defect of long-distance pipeline and the main reason for pipeline failure. At present, pipeline cracks are mainly determined by internal testing and non-destructive testing after excavation. Among them, ultrasonic internal testing has a good identification rate for cracks with a length of more than 25 mm, a depth of more than 1 mm in the base metal or a depth of more than 2 mm in the weld; Magnetic flux leakage internal detection has a certain detection rate for cracks with opening more than 0.25mm, but it is difficult to identify and quantify. In NDT, magnetic particle, penetration, eddy current and radiographic methods have high detection and identification rate. The generation and propagation of cracks will cause local stress concentration in the pipeline, which is prone to brittle fracture, fatigue damage corrosion damage and other failure phenomena, seriously affecting the service performance and reliability of long-distance pipeline. In this paper, which provides a reference for the prevention and control of pipe cracks. What problems will be encountered in the production of copper tubes. The production of copper pipe includes four steps: welding, forming, inspection and pipe expansion.

The price can be changed, and the transaction is affected. According to the feedback from the spot operation, the morning market transaction did not follow the temperature rise: after 9:00, the dealers took turns to raise the price, which was in disorder; Before ten o'clock, it was not as expected, the surrounding markets became loose and the price was low. High hanging, low selling, and low volume. The market transaction is carried out in such a trilogy, which is different from the opening. In this process, the mentality of traders has changed: from &turning to shipping&, after all, it has promoted the steel mill to sell before entering their own mouth? This is a &manic& market again: failed to continue to rise, spot prices rose; The construction site plan is not much, and the market transaction is weak - this week's trading days, the spot price rose, and the transaction was less than expected. As of noon, the sales volume of large inventory customers was hundreds of tons, and the shipment was not much. Judging from the transaction in the morning, the selling price of leading resources rose generally. Among the resources in Kuti, the base price of t2 copper tube was 5050 yuan/ton, and the price of earthquake resistant spiral snail was 5350 yuan; Among the resources provided by the factory, the basic price of threads of Zhongtian, Yonggang and Shagang is 5130 yuan, and the differential between spiral and t2 copper pipes is 360-380 yuan/ton. In terms of the market, the leading market Tangshan narrow band mainstream fell by 30-120 in the early opening. The overall trading situation of copper bars was weak. Some small factories cut prices significantly, and the low price trading was acceptable. Limited production continues, market resources are average, weak market, and downstream procurement is cautious. 355 is the consolidation of the medium broadband market. Today's futures continue to fluctuate. Traders are less willing to ship at low prices and have a strong mood. However, under the pressure of futures the trading atmosphere in the spot market is not good. Copper bars continued to fluctuate in the morning, and traders were affected by multiple factors to make a small weak tone trial deal. From the commercial account, we know that there are few high market transactions, few inquiry calls, and a slightly pessimistic attitude. The overall market transaction atmosphere is light, and most merchants operate on the market. At present, the downstream demand is still low, the demand for terminal replenishment is low, the current market is in a weak situation of supply and demand. Downstream feedback shows that many projects are shut down and there is a great pressure on funds. However, the relevant economic data and side news are too bearish so the futures market is difficult to rebound, and the spot market is mainly responsible for the subsequent drop. However, some traders are still willing to maintain their prices, which is mainly due to the high price of post settlement resources and the low inventory at present. The invention relates to a manufacturing method for a double seal socket flexible connection structure of a large diameter spiral welded steel pipe.

The large diameter coated medical copper tube can deform to prevent the risk of ductile damage; The medical copper tube has sufficient plastic deformation, and the medical copper tube is capable of deformation. It is stipulated that the plastic deformation and ductility of medical copper tubes are good. Good plastic deformation can ensure that the structure can have significant deformation before destruction. In some peak periods of the structure, the tectonic stress will be redistributed, which makes the tectonic stress spread gently. Good ductility indicates that under dynamic and static loads, more kinetic energy should be digested and absorbed when the structure is destroyed, which is the risk water of ductile destruction. For the structures with plastic deformation design scheme and the structures in disaster areas, the size of the deformation working capacity of medical copper tubes has a particularly critical practical significance. 3 Production and processing characteristics of medical copper tubes. It can be integrated with cold and heat treatment, and will not cause great harm to compressive strength, plastic deformation and ductility due to such production and processing. 4 Weldability of medical copper tube. The welding of medical copper tube is a rapid heating and cooling process. The metal materials in the welding and heat affected zone need to go through heating and melting, physical reflection, it has more advantages in strength. Medical copper tubes have many different s in practical application and solid state change in a very short time. The industry trend is a kind of medical copper tube. Because there is no seam in the middle, and each different will make the medical copper tube work well.Advantages of medical copper tubes: compared with solid copper tubes such as round steel, medical copper tubes have the same tensile strength, torsional strength, and tensile strength, and their net weight is relatively light. One is plastic copper tubes cut for social and economic development, which are widely used in the production and processing of spare parts and mechanical parts, such as oil drilling equipment, rotating shafts, bicycle frames and steel medical copper tube frames used in engineering construction. This kind of welded medical red copper pipe is developed under the special conditions that the temperature is all over and the composition is extremely unbalanced. After this kind of welding, which is the specified weldability. 5 Performance of medical copper tube. It refers to the service life of medical copper tube. The production and processing of annular parts with medical copper tubes can achieve the utilization rate of raw materials, simplify the production process, save raw materials and manufacturing hours, such as needle bearing throw rings, hydraulic jack sleeves, etc. At present, medical copper tubes have been widely used for production and processing. Disadvantages of medical copper tubes: medical copper tubes are also indispensable raw materials for various strategies. Drums must be produced and processed by medical copper tubes. Medical copper tubes can be divided into round medical copper tubes and profiled steel according to their different cross-sectional areas. Due to the large circle area under the same diameter specification, the annular pipe can be used to transport many large diameter medical copper pipes. Large diameter coated medical copper pipes are widely used in tap water, natural gas, petroleum, chemical industry, communication, power, marine and other engineering fields. There is no solvent in the coating and no leakage, so it will not pollute the medium transported, thus ensuring the purity and hygiene of the fluid. The temperature range from - 40 ℃ to+80 ℃ can be used alternately in cold and hot cycles, without aging and cracking, the medical copper tube factory will use pickling, which is an indispensable part of most medical copper tubes, Pickling process is the treatment after removing surface oxide scale (Carbon steel - stainless steel - lime saponified phosphorus, butter, oil copper and aluminum pipes - and the old ones, and then wire drawing processing. Then what are the points to be noted when washing? 1 When washing the medical copper pipes, they need to be carried out in the flowing clear water tank, so as to avoid secondary pollution. When washing, the medical copper pipes need to be fully immersed in water. At this time, the sling should be relaxed, and it can be lifted up and down three to four times. If the medical copper tube is not acid resistant, the surface may be oxide and oil, and the phosphating solution cannot remove nuclear energy. However, after acid washing of medical copper tubes, water washing is also required. 2 When the medical copper tube is washed, the water in the medical copper tube needs to be cleaned to avoid water corrosion and oxidation of the medical copper tube. Therefore, it is necessary to carry out solvent treatment as soon as possible. 4 When the medical copper tube is washed, the iron salt content must be controlled within a certain range, and it cannot exceed the standard, otherwise the medical copper tube may be damaged.

retailer.When cutting the copper pipe of air conditioner, use tools such as clamps to fix the copper bar and then cut it, to prevent shaking and resulting in irregular cutting. 3 After the cutting of the air conditioner copper pipe is completed, the cut parts need to be placed in a dry place and then processed again after cooling, otherwise oxidation will occur due to high temperature. Liu Shuchen, director of the Resource Analysis Office of the Information Center of the Ministry of Land and Resources, said that copper bar manufacturers are currently in a period of adjustment in China's mining industry as a whole. In the long run, the mining super cycle driven by China's demand has not changed, especially the growth rate of the country's economy. After the global economy may improve in the second half of the year, and the W-shaped trend will fully emerge. In the second half of the year, there were signs of stabilizing and rebounding. In terms of the macro factors affecting the bulk commodities, and the economic conditions of China and the United States have become the key factors affecting the bulk commodities. The European economic recession is a foregone conclusion, and the possibility of a crisis in the next period of time is also reduced. In recent years, the American market economy has shown the characteristics of better than expected in the first quarter and weaker than expected in the second quarter. Since January, the global price of medical copper tubes has gradually got rid of the main tone of this year's shock and decline. &Air conditioning copper tubes show signs of stabilizing and rebounding. The three-month copper on the London Metal Exchange once rebounded nearly 7% from the year's low point, zinc and other products have also rebounded. Only nickel products including aluminum, a basic metal product,Bayan hongerStainless steel coiled plate, has remained weak.

In addition, it is very strong, not easy to be corroded, and can adapt to various environments. It can be used normally at low and high temperatures, so copper pipes need to be selected many times in other places.The color change on the outer surface of the copper tube is difficult to control due to environmental factors. To prevent moisture absorption on the surface and core of the annealed brass tube, a constant temperature and humidity packaging room can be built. Packaging in the packaging room can avoid the color change on the outer surface of the copper tube. However it is not easy to control the situation that occurs in the processing process. The cost of ensuring constant temperature and humidity in the whole workshop is too high. The following measures are taken to control the process materials: In the season of high temperature and humidity, during the production and processing of copper tubes, the amount of oil coating on the surface of copper tubes can be increased to form an oil film on the surface of copper tubes, which can isolate water vapor and corrosive gases, and prevent the corrosion of the surface of copper tubes; The humidity in the air at night is high, and the outer surface of the copper pipe is prone to corrosion and discoloration at night. Closing the doors and windows of the workshop at night can make the situation worse; After the coil surface is cleaned in the rewinding process, the coating amount of passivation agent on the copper tube surface is increased. After blanking in the rewinding process, plastic bags shall be added to the whole support material to further reduce the contact between the copper pipe and the air and prevent the surface of the copper pipe.

For the production and processing of sculpted copper tubes, the sheet metal shall be first opened in the sheet metal workshop according to the dimensions shown in the drawings, and then use the bending machine to form the edge according to the drawing forming diagram. The shaped copper pipe shall also be installed with reinforcing ribs as required, and the four corners of the shaped plate shall be welded well. The welded parts shall be sent to the grinding workshop, and the spraying surface shall be polished and the welding interface shall be polished and leveled. The polished modeling copper pipe is then sent to the spraying workshop for processing. Before spraying, the surface of the sculpted copper pipe shall be chrome treated and the process hole shall be drilled, so as to ensure that the sculpted copper pipe can be hung on the spraying line well, and the painting can be smooth without flow marks, and the color is consistent without color difference. After that, according to customer demand, the qualified products are pasted with protective film and bound with bubble film or wooden box.

Bayan honger.The surface coating of medical copper tube is very important. Observe its thickness, how to prevent the aging of medical copper tube? How to select the foam density of medical copper tube Good medical copper tube and foam density are very high and hard. Check the quality of aluminum zinc coated color steel plate on the surface. As exterior wall thermal insulation decorative plate. Then use your hand to break it up and down to see if it is easy to deform. If you break it with force, it will deform, which is not good. 3 See the price.

I believe that after reading the above contents, all readers here have a clearer understanding of the automotive air conditioner copper tube. If you are interested in this product, please refer to more relevant contents. Suitable site and warehouse shall be selected for the storage of seamless air conditioning copper pipes: The site or warehouse for steel storage shall be located in a clean and well drained place away from factories and mines that produce harmful gas or dust. With the rapid development of economy, the number of cars is also fast. Nowadays, people can't live without cars. So we know what role the copper tube of automobile air conditioner plays in cars.

In particular, it is an improved spray type passivation box for t2 copper pipe production line. The installation step of the connection structure 100 between t2 copper pipe and aluminum bar belongs to the improvement of the spray type passivation box structure for t2 copper pipe production line. The passivation solution spray box is set above the side of the passivation solution box, the passivation solution spray box with downward sloping bottom is connected with the inlet of the passivation solution box by the outlet set on the box wall at the bottom of the inclined bottom, the inlet of the passivation solution box is located on the box wall above the passivation solution box, the upper side of the passivation solution box is installed with a passivation pump, and the inlet pipe of the passivation pump is connected with the passivation solution box, The outlet pipe of the passivation pump is connected with the upper port of the passivation liquid spray box. With reasonable structure and convenient operation, it is convenient for operators to add passivation liquid to the passivation box, clean colloidal crystals at the bottom of the passivation box, avoid equipment blockage, avoid crystals adhering to the zinc layer on the surface of galvanized pipe, and improve the surface quality of galvanized steel pipe.