AachenSelf pro
Aachenfork lifAachenCylinder mounted hydraulic lifting platform,
Before installation, pay attention to alignment, leveling, and alignment points, and confirm that the foundation meets the requirements before construction.
A hydraulic elevator is a type of elevator equipment consisting of a walking mechanism, hydraulic mechanism, and enters the lower end of the hydraulic cylinder through an oil filter,AachenDouble shear hydraulic lifting platform, explosion-proof electromagnetic directional valve, throttle valve, hydraulic control one-way valve, and balance valve, causing the hydraulic cylinder to move upwards and lift heavy objects. The return oil at the upper end of the hydraulic cylinder returns to the oil tank through the explosion-proof electromagnetic directional valve, and its rated pressure overflow valve is adjusted. The pressure gauge observes the reading value on the pressure gauge.
Aachen.What technical issues are required for the installation of hydraulic freight elevators? The installation of hydraulic freight elevators is actually quite complex. If you do not understand the equipment pictures designed by the elevator manufacturer and the detailed situation of the hydraulic freight elevator designed by the elevator manufacturer, installation errors may occur, leading to equipment failure of the freight elevator! When installing hydraulic freight elevators, it is necessary to accurately calculate the size of the pit. The guide rail hydraulic freight elevator is a freight elevator composed of chains, guide rail torque tubes, and other components, mainly driven by the chain to assist in the upward and downward telescopic lifting of the freight elevator. The pulleys at the four corners of the countertop should be fixed on the surrounding guide rails. The entire elevator equipment is installed on the wall, and wall mounted installation is chosen to enhance the stability of the freight elevator. Choosing the appropriate wall size also requires careful planning.
After the pre installation is completed, the pre installed equipment should be fixed, and the positions of cables, oil pipes, and components such as the pre installed frame should be confirmed to be correct before reinforcement work can be carried out. Reinforcement requires welding or screws, and the hydraulic cargo elevator after reinforcement has robustness and safety.
.Users should arrange dedicated personnel to operate hydraulic elevators, formulate usage details and safety precautions for hydraulic elevators based on their own situation, and hang them on the
Protective device: In case of power or oil circuit failure, there should be a safety rope to prevent the workbench from falling out of control. (Allow controlled descent)
After 10000 hours of operation on the hydraulic lift, major repairs will be carried out to the mechanical and electrical systems.
To consider its capacity, generally mobile equipment takes 2-3 times the high flow rate of pump Z, and fixed equipment takes 3-4 times.
The manufacturer of hydraulic cargo elevators tells you the reason for the instability of hydraulic lifting equipment. Hangzhou hydraulic cargo elevator equipment has always had good stability, mainly used for heavy types of goods. However, during use, Hangzhou hydraulic cargo elevators may inevitably encounter some faults during the lifting process, such as very unstable conditions. What is the reason for the instability of the elevator? How to solve these problems?
Electrical equipment or component failures. Hydraulic elevator manufacturers tell you that the main reasons for high noise generated by electric motors are: bent or severely worn motor rotors, or damaged bearings, which cause electric motors to sweep and produce noise; The cooling fan of the electric motor is damaged or not firmly fixed, resulting in high noise; The electric motor is not firmly fixed and can also cause vibration, producing high noise.
Packaging strategy. There is air in front of the pilot valve of the elevator overflow valve noise overflow valve. The damping hole on the main valve core of the overflow valve is blocked by oil dirt, and the pilot valve and valve seat are matched without spring deformation or incorrect installation. The remote control port has excessive oil flow, low or high hydraulic oil viscosity, and resonance occurs with components in the circuit. Troubleshooting: Strengthen sealing, repeatedly adjust the pressure, exhaust and clean the valve body several times, Make the damping hole unobstructed, repair or replace the spring, reduce the flow of the remote control port, replace the oil, and other components. The pressure setting of other components should not be similar to the pressure setting of the relief valve. 5. The noise of the elevator pipeline is usually caused by excessive dead bends or loose fixed sleeves in the hydraulic pipeline.
When using hydraulic elevators, the main causes of noise are mechanical mechanism failures hydraulic system failures, etc. Today, the manufacturer of hydraulic cargo elevators will introduce to you the reasons for the noise generated by hydraulic elevators.
The hydraulic lifting platform often checks the connection status of each part, and if there is any looseness, it should be tightened. The connection bolts of the machine body should be checked for tightness when the elevator body is under pressure (the compression condition can be formed by rotating the arm). All connecting shafts need to have split pins and need to be fully opened.
The combined platform is often used in small workshops with small volume of goods. However, because this platform needs to complete two functions at the same time it inevitably increases the distance of handling tools/vehicles in the workshop.
Good reputation.Protective device: In case of power or oil circuit failure, there should be a safety rope to prevent the workbench from falling out of control. (Allow controlled descent)
Generally speaking for situations with large lifting loads and small lifting heights, a lifting mechanism should be selected. For situations with small loads but large lifting heights, a lifting mechanism should be selected. According to the initial structure of the jacking, in order to meet the stability requirements, and in order to achieve the same effective area as the jacking force, the oil cylinder is added. If the latter is larger, a lifting mechanism should be selected.
The vibration range is proportional to the lifting height. The higher the height, the larger the shaking range, especially for mobile hydraulic cargo elevators. When the working height exceeds 10 meters the wind ropes at the four corners of the hydraulic cargo elevator should be tightened to strengthen leg protection, increase stability,AachenIndoor hydraulic lifting platform car, and reduce shaking.
Aachen.Before installation, the installation personnel should confirm the infrastructure such as the foundation and shaft, pay attention to alignment, leveling, and alignment points, and confirm that the foundation meets the requirements before construction.
Do not use hydraulic lifting equipment with malfunctioning issues. The problem should be resolved before carrying cargo.
Therefore, in the hydraulic pipeline assembly line, it is necessary to avoid dead bends as much as possible and check the tightness of the sleeve in a timely manner.