Schiedam Hydra
Schiedam DoublRegularly check all wires and cables for damage. It is necessary to wrap and replace the damaged parts in a timely manner.
There is air in front of the pilot valve of the elevator overflow valve noise overflow valve. The damping hole on the main valve core of the overflow valve is blocked by oil dirt, and the pilot valve and valve seat are matched without spring deformation or incorrect installation. The remote control port has excessive oil flow, low or high hydraulic oil viscosity, and resonance occurs with components in the circuit. Troubleshooting: Strengthen sealing, repeatedly adjust the pressure, exhaust and clean the valve body several times, Make the damping hole unobstructed, repair or replace the spring, reduce the flow of the remote control port,Schiedam 3-meter hydraulic lifting platform, replace the oil, and other components. The pressure setting of other components should not be similar to the pressure setting of the relief valve. 5. The noise of the elevator pipeline is usually caused by excessive dead bends or loose fixed sleeves in the hydraulic pipeline.
Schiedam .Check valve leakage, oil pipe check valve leakage. The solution is to carefully check whether the one-way valve is functioning properly. If it is not normal, it is recommended to replace the one-way valve with a new one.
When the hydraulic lifting platform is working, the load cannot exceed its rated load. When it is raised to a certain height, the larger the mass of the object, the greater the shaking
.When the hydraulic system malfunctions, motor, valve, and hydraulic installation after repairing the hydraulic system, which can easily cause vibration and generate significant noise.
There are many reasons for unstable workbench descent, such as overload, unstable support, severe eccentric load, hydraulic oil impurities, etc. In response to the above reasons, it can be solved by reducing the load, adjusting the center of gravity of the load, and replacing hydraulic oil wholesale for hydraulic cargo elevators.
The main device does not engage. When this fault occurs check whether the three-phase power supply is normal, whether the internal and external emergency stop button switches, the electric lock switch are turned on, whether the three-phase electrical phase sequence is correct, and whether the relay working indicator light is on.
The electromagnetic coil of the electromagnetic directional valve is not firmly fixed, new steel wire ropes will not suddenly break when used under normal circumstances, unless incorrect operation or safety protection devices fail, as the load borne by the steel wire may exceed its breaking capacity. The damage to the steel wire rope of the cargo elevator is mainly gradually formed during long-term use. After a certain period of repeated bending and friction, the steel wire on the surface of the steel wire rope will experience bending fatigue and wear, and the steel wire on the surface layer will gradually break. At this point, if it cannot be used again, and frequent separation and suction can also produce high noise.
Excellent quality.The smoothness of the gearbox, gearbox, external meshing gears, and hydraulic oil are all carried out according to the requirements in the smoothness table.
The development of elevators is at its peak as many manufacturers have chosen more multi-story buildings to fully utilize the site, so they also need a device to facilitate the improvement of goods.
The hydraulic lifting platform is a manually movable type,Schiedam Self hydraulic lifting platform, and the lifting power of the platform is a two machine or three-phase power supply. It has manual and electric power and is also equipped with a hand pump for use in case of power outage. This series of platforms have the characteristics of flexible movement, stable lifting, and easy operation, and are mainly used in factories, government agencies, commercial stores, and the construction and decoration industry.
There is noise inside the hydraulic cylinder. When replacing the hydraulic oil, there was air in the hydraulic cylinder due to an operational error. Under high pressure, it is easy to generate cavitation and high-frequency noise. When the rod is bent or replaced with a new seal, the new seal is too tight, which can also produce significant noise. If it is a problem of tight sealing, the noise can be reduced after running in for a period of time. If the rod is bent, it needs to be corrected. In addition, hydraulic pipelines should use hoses as much as possible, even when arranging pipelines, it can reduce vibration and noise, and the pipelines should avoid dead bends as much as possible.
Quality risk.Remember not to overload, overload is the root cause of many faults.
If any problems are found, please contact the manufacturer in a timely manner to avoid exceeding the warranty period.
Oil leakage is a common malfunction. Due to loose joints or damaged sealing rings, oil leakage may occur. Therefore, this fault can be solved by tightening the oil leakage joint or replacing the damaged sealing ring.
Schiedam .Introduction to the unloading lifting platform: The unloading lifting platform is a specialized auxiliary equipment used in conjunction with forklifts for cargo loading and unloading. With it forklifts can directly drive from the ground into the interior of car compartments for batch loading and unloading operations. The warehouse unloading platform products use manual hydraulic power and do not require power supply. Only one person needs to operate to achieve safe and fast loading and unloading of goods. It can reduce a lot of labor, improve the efficiency of loading and unloading operations, speed up the flow of materials, there should be a device to make the workbench emergency descend.
After 5000 hours of elevator operation, carry out medium maintenance on the mechanical and electrical systems.