Okefork lifterChemical composition

Hydraulic oil should be kept clean and replaced every 6 months; When repairing, maintaining, and cleaning the elevator, be sure to support the support rod.

Talking about the daily maintenance and use of hydraulic lifting platform motors. Overloading is strictly prohibited, as overloading can increase the burden on the motor and in severe cases, cause the motor to burn out.

Oke.Many people believe that the mechanical strength of the elevator itself is relatively high when using it, so they did not strictly follow the installation method specified in the manual during the installation process. Little did they know that this would cause increased wear and tear of the parts and inflexible operation. In addition, they should pay attention to the installation precautions corresponding to the working environment and not be careless. Proper installation, use, and maintenance of elevators are important steps to ensure the normal operation of mechanical equipment. Therefore, when installing the elevator, please be sure to strictly follow the installation and use related matters below, and carefully assemble and use it.

Guide rail type cargo elevators are a type of equipment for transporting heavy objects up and down, and have great applications in factories, workshops, and other places. For this type of heavy machinery, its daily maintenance and upkeep are very important, because some small details can have a significant impact on the operation safety of the equipment if not paid attention to. Therefore,OkeHydraulic mobile lifting platform, attention should be paid to the daily maintenance of cargo elevators.

.When using, the four legs should be firmly supported on a solid ground (based on the walking wheel about to leave the ground),OkeHydraulic lifting platform supplier, and sleepers can be used when necessary.

When encountering overheating in the hydraulic elevator motor, it is necessary to stop it in a timely manner, eliminate the fault, and continue running. The motor bearings should be in good condition.

The size of the oil cylinder should be minimized as much as possible while meeting the design requirements. The smaller the size of the oil cylinder, the faster the lifting speed.

Preparation before folding and installation of the elevator. Carefully prepare a special construction plan for installation and provide safety technical disclosure to the installation personnel.

A type of elevator equipment consisting of a walking mechanism, hydraulic mechanism, electric mechanism, and support mechanism. The hydraulic oil forms a certain pressure by the vane pump, and enters the lower end of the hydraulic cylinder through the oil filter isolation electromagnetic directional valve, throttle valve, hydraulic control one-way valve, and balance valve, and its rated pressure overflow valve is adjusted. The pressure gauge observes the reading value on the pressure gauge.

The pressure of the lifting platform is very important. When lifting goods, the pressure of the lifting platform will test the weight of the goods. If it is overloaded, the general lifting platform will prompt, which serves as protection. Therefore, now lifting platforms are equipped with pressure gauges. Hydraulic machinery should remind everyone to pay attention to the following points: the precautions for using small lifting platforms are based on pressure. Their load-bearing capacity is very poor and their size is small. When using the lifting platform, it is necessary to pay attention to its use. If overloaded, it will cause structural damage to the lifting platform. We have mentioned this many times before when using it.

Statistics.After entering winter, which requires users to perform seasonal maintenance and upkeep on the elevator. Below the editor will briefly introduce the winter maintenance precautions and key points of the elevator.

Carefully prepare a special construction plan for installation and provide technical disclosure to the installation personnel. I have been engaged in various types of scissor lift manufacturers and other materials for many years, causing serious damage to the platform and causing the table to tilt. Please carefully check that the general shear type high-altitude work platform was not strictly tested for tilt before leaving the factory, and was put into the market, causing many accidents. For small enterprises, they are not very concerned about this aspect of tilt detection, This is also why there are such a large number of lifting equipment with this problem. The problems with the oil cylinder and power unit system are often due to insufficient power and substandard oil cylinder quality, which are also very important issues for enterprises themselves.

When encountering overheating in the hydraulic elevator motor, it is necessary to stop it in a timely manner, eliminate the fault, and continue running. The motor bearings should be in good condition.

Recommendation and consultation.When encountering overheating in the hydraulic elevator motor,OkeLifting hydraulic platform, it is necessary to stop it in a timely manner eliminate the fault, and continue running. The motor bearings should be in good condition.

The brake operators of each mechanism on the equipment should regularly inspect and adjust the clearance of the brake pads and wheels, ensuring flexibility and reliability.

What are the common faults of hydraulic lifting platforms? The hydraulic lifting platform's oil cylinder is severely damaged, resulting in uneven lifting height of the oil cylinder. It is recommended to carefully check whether the oil cylinder is normal.

Oke.According to Beijing regulations, the arrival time is within 30 minutes.

Check the hydraulic oil quality and level. When the lifting platform is raised to a high position, the hydraulic oil level should be 40-50 millimeters higher than the bottom of the oil tank. When the color of the hydraulic oil darkens, the oil becomes sticky or there are foreign objects such as gravel in the oil, the hydraulic oil should be replaced in a timely manner. The hydraulic system of the lifting platform should be checked for hydraulic and pipeline connections. If the pipeline is damaged, it should be replaced immediately; When there is looseness in the connection part, tighten the pipe joint.

Preparation before folding and installation of the elevator. Carefully prepare a special construction plan for installation and provide safety technical disclosure to the installation personnel.