Chirila BangbuSquare aluminum tubeThe power of technology is awesome

The demand for t2 copper tubes is increasing. At the same time, in the market, the quality identification method of t2 copper tube for grid fittings is currently accompanied by rapid economic development. There are many kinds of sales, different types, different purposes, and different quality. Therefore, when purchasing, you should be clear and have certain selection skills. Here we introduce the quality identification method of t2 copper tube. The color of t2 copper tube depends on the color of t2 copper tube. Although the external color is a visible factor, the color of the product is closely related to its production process and quality control. If the product is bright in color and high in glossiness, it is generally superior to the product with poor color. The t2 copper tube with uniform thickness should be selected. Because some small manufacturers are limited in technology and process, it is difficult to ensure that the product thickness is uniform and neat. Therefore, the thickness is also an important factor to test the quality of the pattern plate. Later, the casting process of t2 copper tube.

Handle carefully to prevent damage and scratches. 2 When installing the keel, protect it from impacting the medical copper pipe. 3 After the installation of thermal insulation curtain wall, in order to prevent personnel from approaching, special personnel should check the distance from the ground curtain wall. 4 For each process close to the curtain wall, the medical copper pipe shall be temporarily protected before construction and can be covered with fiberboard. Even after the construction is completed, some temporary protective measures should be taken to achieve the effect of later use. 3 On the premise of considerable cohesiveness, the exterior wall external thermal insulation decorative integrated board of high-rise buildings should meet the principle of flexible gradual change, and disperse and absorb seismic stress as far as possible to reduce the impact on medical copper pipes. 4 The medical copper pipe shall be made of waterproof and moisture permeable external insulation materials to avoid damage to the wall caused by water or steam migration. 5 Under the action of negative wind pressure, the volume expansion of the air layer in the insulation layer will damage the insulation layer. The aging of medical copper pipe will affect the use of building materials to a certain extent. When it reaches its service life it needs to be replaced to prevent the trouble of aging in life. 6 The thermal expansion and cold contraction caused by the temperature difference change will cause the volume change of the non structure of the medical copper tube. Such medical copper tube has a shorter service life than the plate in normal use, and needs regular maintenance according to regulations.

Chirila Bangbu.This week, the capacity utilization rate of 163 steel plants was 821%, which was 0.06% higher than that of the previous week. The utilization rate of eliminated capacity was 90.29%, which was 0.79% lower than that of the same period last year. The profitability of steel plants was 8%, which was 0.61% higher. This week due to the impact of environmental protection, there were many small blast furnaces in Hebei Province. Although some steel plants have resumed production, this week's hot metal output has been affected. In addition, a steel plant in Shanxi Province has resumed production after being shut down due to environmental protection problems. The resumption of production of large blast furnaces in Hebei Province has led to a slight increase in capacity utilization and a decrease in operating rate. With the end of production restriction next week and the resumption of production of some blast furnaces the capacity utilization rate may continue to increase.

However, it may cause recoverable temporary damage to people who have been away from these radioactive sources for a long time. The DC brushless motor with small volume and large power is adopted which can operate without fault for a long time even if it is opened or closed. Target There will be no sharp decline in the price of copper tubes in Linyi at the end of the month. The price of plastic coated copper pipe will continue. Pop up the position line and line, select PVD chromium nitride ring and molybdenum spraying ring as the matching materials for the plastic coated copper pipe, adhere to the wear form condition simulation criteria of the sample test, use the self-developed opposed reciprocating wear tester, carry out the load level test, wear test, lean oil test, and research the load. As for the corrugated process of the finished plastic coated copper pipe as claimed in claim 1, the radiation source for the engineering design of the integrated rigid flexible connection plastic coated copper pipe belongs to the low hazard source. Basically, it will not cause artificial damage. The basic principle of the foundation of the integral rigid flexible connection plastic coated copper pipe sluice discussed the influence of process parameters and heat treatment process on the microstructure, phase distribution and mechanical properties of the alloy, and obtained some important research results. The number of joints of steel pipes and plastic coated copper pipes on the same section shall not exceed 50% of the number of pipes. Before installation, the pipe shed shall sweep and clean the hole with drill bit or high-pressure air, and the scum in the hole shall be removed, Ensure the aperture (The hole diameter shall not be less than 127cm, and the hole depth shall meet the requirements to prevent hole plugging. Most of the seamless steel pipes produced now are hot-rolled. Because of the high temperature, the deformation resistance is relatively small,Chirila BangbuLow alloy plate, and generally the steel plate is used for rolling. In this operation, the detailed thickness of the steel plate shall also be considered. If it is about the harmful elements with relatively low accuracy requirements, extended section by section, and What does plastic coated copper pipe with a diameter of 1 reflect in life when the weld length is added to 30 for the joint steel pipe of the pipe extension joint? Plastic coated copper pipe can also produce welded pipes with different pipe diameters from billets of the same width. However, which is commonly referred to as opening. Then cut the corners of these open sheets according to the height of the edge, and then use the bending machine to form the edge according to the drawing forming diagram. The shaped copper pipe shall also be installed with reinforcing ribs as required, and the four corners of the shaped plate shall be welded well. The welded parts shall be sent to the grinding workshop, and the spraying surface shall be polished and the welding interface shall be polished and leveled. The polished modeling copper pipe is then sent to the spraying workshop for processing. Before spraying, the surface of the sculpted copper pipe shall be chrome treated and the process hole shall be drilled, and the painting can be smooth without flow marks, and the color is consistent without color difference. After that, according to customer demand, the qualified products are pasted with protective film and bound with bubble film or wooden box.

Plastic coated copper pipe is a kind of non-metallic material pipe with light weight, high strength and corrosion resistance. The plastic coated copper pipe is made of glass fiber with resin base weight, which is wound on the rotating hollow floor step by step according to the processing technology regulations, and the stone sand is laid on the ground evenly for a long distance in the middle of the chemical fiber as the intermediate weathering layer. The price quotations of plastic coated copper pipes with different thicknesses are also different. Here, we will explain the factors that determine the thickness of the plastic coated copper pipe design scheme. Appearance and specification of mpp cable duct 1 Color: generally orange red, other colors can be implemented according to the contract of both parties. 2 Appearance quality: The inner and outer walls of the pipe fittings shall be smooth, clean and even, and shall be free of steam bubbles, cracks, cracks,Chirila Bangbu316L stainless steel pipe, molting, and obvious marks, dents, residues, dissolved discoloration lines and uneven colors. The inner holes of the pipe shall be laser cut and leveled and vertical to the pipe centerline. The inner holes shall be smooth and free of burrs. Specification: The length of pipe fittings is generally 6000 or 9000mm, which can also be negotiated by both parties. The specification error shall conform to dl/t801; The bending degree of the hose shall not exceed 1% of the nominal pressure. Some key points in the process of embedding plastic coated copper pipe: the embedding process of plastic coated copper pipe is very worthy of great attention. Although the actual operation in the process of embedding is relatively simple, there may be many key points. Pay special attention to the leveling and straightness of the road surface when threading, In other words, if the road surface is seriously uneven, it is seriously affected by external forces. Relevant countermeasures must be taken and fine sand and dirt should also be prohibited from seeping into the pipe during the burial process, so as to diligently maintain its compliance with the regulations during the burial process. The process of embedding the plastic coated copper pipe involves the problem of marking. In fact, the marking that can be carried out according to this marking in the process of maintenance and repair is the key inspection index value of the commodity. If it is found that there is a problem with a certain section of cable, it is only necessary to find matching marks for immediate maintenance. Number of layers of cloth stacking: all layers are made strictly according to the design scheme, without additional construction, which increases the cost. 2 Resin: high temperature resistance, not easy to deform under stress. Plastic coated copper pipes are generally assembled from high-quality SMC water tank plates. Its characteristic is that it can select food grade stainless steel resin. Therefore, in view of the good water body clean up the natural environment and zero pollution, the commodity development trend has certain characteristics such as high compressive strength, light weight,Chirila Bangbu12CR1MOV alloy plate, corrosion resistance, beautiful and generous appearance design scheme, long service life, and more convenient management methods in maintenance. Cloth quality: the specification of cloth surface is the same, pure platinum cloth is thick, and it is thick with blended cloth or pure old coarse cloth. The thickness of fiberglass filament winding: our products are high-tech support points of fiberglass anti-corrosion ring, which ensures the bearing pressure of the products. In addition, if you must select the thickened type, you can yze the vertical cross type difficult winding when winding the winding machine, until the thickness and compressive strength of the thickened type are basically achieved.

The large diameter coated medical copper tube can deform to prevent the risk of ductile damage; The medical copper tube has sufficient plastic deformation, and the medical copper tube is capable of deformation. It is stipulated that the plastic deformation and ductility of medical copper tubes are good. Good plastic deformation can ensure that the structure can have significant deformation before destruction. In some peak periods of the structure, the tectonic stress will be redistributed, which makes the tectonic stress spread gently. Good ductility indicates that under dynamic and static loads, more kinetic energy should be digested and absorbed when the structure is destroyed, which is the risk water of ductile destruction. For the structures with plastic deformation design scheme and the structures in disaster areas, the size of the deformation working capacity of medical copper tubes has a particularly critical practical significance. 3 Production and processing characteristics of medical copper tubes. It can be integrated with cold and heat treatment, and will not cause great harm to compressive strength, plastic deformation and ductility due to such production and processing. 4 Weldability of medical copper tube. The welding of medical copper tube is a rapid heating and cooling process. The metal materials in the welding and heat affected zone need to go through heating and melting, physical reflection, cooling and crystallization, and solid state change in a very short time. The industry trend is a kind of medical copper tube. Because there is no seam in the middle, it has more advantages in strength. Medical copper tubes have many different s in practical application, and each different will make the medical copper tube work well.Advantages of medical copper tubes: compared with solid copper tubes such as round steel, medical copper tubes have the same tensile strength, torsional strength, and tensile strength, and their net weight is relatively light. One is plastic copper tubes cut for social and economic development, which are widely used in the production and processing of spare parts and mechanical parts, such as oil drilling equipment, rotating shafts, bicycle frames and steel medical copper tube frames used in engineering construction. This kind of welded medical red copper pipe is developed under the special conditions that the temperature is all over and the composition is extremely unbalanced. After this kind of welding, it can produce detailed welding joints to maintain special performance indicators, which is the specified weldability. 5 Performance of medical copper tube. It refers to the service life of medical copper tube. The production and processing of annular parts with medical copper tubes can achieve the utilization rate of raw materials, simplify the production process, save raw materials and manufacturing hours such as needle bearing throw rings, hydraulic jack sleeves, etc. At present, medical copper tubes have been widely used for production and processing. Disadvantages of medical copper tubes: medical copper tubes are also indispensable raw materials for various strategies. Drums must be produced and processed by medical copper tubes. Medical copper tubes can be divided into round medical copper tubes and profiled steel according to their different cross-sectional areas. Due to the large circle area under the same diameter specification, the annular pipe can be used to transport many large diameter medical copper pipes. Large diameter coated medical copper pipes are widely used in tap water, natural gas, petroleum, chemical industry, communication, power, marine and other engineering fields. There is no solvent in the coating and no leakage, so it will not pollute the medium transported, thus ensuring the purity and hygiene of the fluid. The temperature range from - 40 ℃ to+80 ℃ can be used alternately in cold and hot cycles without aging and cracking, so it can be used in cold areas and other harsh conditions. When processing medical copper tubes, the medical copper tube factory will use pickling, which is an indispensable part of most medical copper tubes, Pickling process is the treatment after removing surface oxide scale (Carbon steel - stainless steel - lime saponified phosphorus, butter, oil, copper and aluminum pipes - and the old ones, and then wire drawing processing. Then what are the points to be noted when washing? 1 When washing the medical copper pipes, they need to be carried out in the flowing clear water tank, so as to avoid secondary pollution. When washing, and it can be lifted up and down three to four times. If the medical copper tube is not acid resistant the sling should be relaxed, the surface may be oxide and oil, and the phosphating solution cannot remove nuclear energy. However, after acid washing of medical copper tubes, water washing is also required. 2 When the medical copper tube is washed, the water in the medical copper tube needs to be cleaned to avoid water corrosion and oxidation of the medical copper tube. Therefore, it is necessary to carry out solvent treatment as soon as possible. 4 When the medical copper tube is washed, the iron salt content must be controlled within a certain range and it cannot exceed the standard, otherwise the medical copper tube may be damaged.

Some problems. For example, in the preliminary manufacturing of copper tubes for air conditioners for automobiles, the materials for air conditioners can be selected according to the actual size required by users, and then the copper tubes for air conditioners for automobiles can be manufactured, followed by pickling. The produced copper tubes for air conditioners are put into the pickling tank for pickling, and then stretched. Then the pickled copper tubes for air conditioners are stretched according to their size requirements.

At present, the steel plant has a slightly serious loss, so it is more cautious to purchase pig iron. Although most of the manufacturers who shut down the furnace and carried out maintenance have postponed the return to work plan, there are still many sources of goods available to the steel plant and most of the steel plants currently adopt the operation mode of purchase on demand and purchase on demand, which makes it difficult to guarantee the delivery of iron plants. The price of pig iron for steelmaking in a few regions is still high, and the purchase is mainly wait-and-see. It is expected that the domestic T2 copper bar market in October will be mainly weak.

Manufacture gear, shaft sleeve, worm gear and other high-strength wear-resistant parts and high corrosion resistance elastic components. Key points of semi continuous casting process for copper tube: The copper tube has strong air absorption, easy oxidation and slag formation, large solidification shrinkage, poor thermal conductivity and other casting properties, and poor casting performance; Before casting, some alkaline earth metal compounds, such as Na3A lF6 and NaF mixture, are used as slag removers to purify the copper liquid, which is effective for improving the purity of liquid metals and the crystal structure of ingots. The pouring temperature of copper pipes is generally 1120~1180 ℃, and the pouring temperature of large-sized ingots is generally lower. The casting speed of the copper tube is low, and the metal level in the mold can be cast in an open flow manner without any protection; The melt needs to enter the mold through the hole at the bottom of the funnel. The design of funnel aperture should meet two conditions at the same time: one is to ensure the flow matching the casting speed; Second, ensure that the liquid level in the funnel is always kept at a certain height, so that the scum on the liquid level cannot flow into the crystallizer from the funnel hole; The copper tube ingot is easy to produce air holes and concentrated shrinkage cavities. At the end of pouring, named after its yellow color. Copper content is 56%~68% brass, and its melting point is 934967 degrees. Brass has good mechanical properties and wear resistance, and can be used to manufacture precision instruments, ship parts, gun casings, etc. Different zinc content also has different colors. For example, 20% will be red and yellow, while when the zinc content is 20%, 30% will be brown and yellow.

knowledge.Plastic coated copper pipe is one of the safe carbon fiber products. Its specific content is a new structural composite building decoration material that can be produced according to the development trend of production and manufacturing by using a glass fiber as the synergist and resin as the adhesive based on the application of full intelligent technical automatic control system equipment.

Xiao Bian would like to talk about the production of a copper tube for automotive air conditioners to help you better understand this product. During the production of automotive air conditioning copper tubes, bending deformation and torsion deformation are very easy to occur. Therefore, attention should be paid to the use of straighteners in production, and the tubes should be straightened to meet the requirements of automobiles for automotive air conditioning copper tubes. The air conditioner copper pipe straightener uses vertical and horizontal rubber rollers to straighten it, so that the air conditioner copper pipe can be used by users to a certain extent.Nowadays, most straighteners can only straighten some copper pipes for automobile air conditioners with low accuracy, while most straighteners with high accuracy can only straighten some copper pipes for automobile air conditioners with small defects. Therefore, the straightening equipment used for rectangular pipes with different bending degrees is different, which brings a lot of inconvenience to the production of copper pipes for automobile air conditioners. Therefore, some other construction processes should be used, To solve some problems arising from the above production. For example, in the preliminary manufacturing of medical copper tubes for automobiles, the air conditioner copper tube materials can be selected according to the actual size required by the user, and then the air conditioner copper tubes for automobiles can be manufactured, followed by pickling, putting the produced air conditioner copper tube materials into the pickling tank for pickling, and then stretching, and then stretching the pickled air conditioner copper tubes according to their size requirements. The warehouse shall not be mixed with acid Alkali, salt, cement and other materials that are corrosive to steel are stacked together. Air conditioning copper pipe is based on carbon structural steel. The phenomenon of torsional deformation of air conditioning copper pipe requires weeds and all sundries on the site. One or more alloy elements shall be added appropriately to improve the mechanical properties, toughness and hardenability of the annealing steel. The automobile air conditioner copper tube is also called the air conditioner copper tube. In fact, it refers to a kind of air conditioner copper tube with equal side length. The automobile air conditioner copper tube is made of strip steel as raw material, and then processed and rolled by relevant processes. It is generally made into a circle after the strip rod is unpacked, straightened, curled and welded. Among them, hardness is an index to measure the degree of hardness and softness of automotive air conditioner copper tubes. At present, the commonly used hardness method for measuring product hardness in production refers to the use of an indenter with a certain geometric shape to measure the hardness value of the metal surface being tested under a certain load according to its degree of coverage. The air conditioner copper pipe in the automobile air conditioner copper pipe is also divided into weld and seamless. Seamless air conditioner copper pipe is a metal material formed by directly using seamless round pipe. The plasticity of the air conditioner copper pipe refers to the ability to deform under a certain load without its original performance. The copper pipe for automobile air conditioner is a hollow and square section. The light thin-walled copper pipe for air conditioner is also known as steel cold-formed profile. It is a square section steel made of strip or coiled plate after processing in the cold bending area and high-frequency welding. In addition to being used in the automobile industry, the air conditioning copper pipes are used in construction, machinery manufacturing, steel construction and other projects, shipbuilding, solar power generation support, steel structure engineering, electric power engineering, power plants, agricultural and chemical machinery, glass curtain walls, boiler construction, highway railings, housing construction, pressure vessels, power station equipment bridges, lifting and transportation machinery and other high load welding structures. In addition to the thickening of the wall, this kind of automobile air conditioning copper tube has better comprehensive mechanical properties and has the advantages of hot processing, cold processing, weldability and corrosion resistance.

In addition, the stress corrosion cracking inside the stainless steel plate will cause the transition film on the surface of the stainless steel plate. Therefore, the surface of plastic coated copper pipe shall be cleaned to a certain extent to ensure its service life. The oil cracking tube circuit breaker must be selected. The fracture of the plastic coated copper pipe shall be kept on a true circle, and the fracture line shall be inclined to the pivot of the plastic coated copper pipe. Too large is the reason for cutting plastic coated copper pipe into flat or oval shape, so moderate energy shall be used when cutting square steel pipe. What matters should be paid attention to when purchasing plastic coated copper tubes.

The materials of the packer shall be packed with steel strip and added according to the diameter and weight of the petroleum cracking pipe. The degreased copper pipe from the pipe can be packed without a packer. If there are wiring ports on both sides of the cracked oil pipe, external thread devices shall be provided for safety protection. Brush the nozzle with clean oil or anti rust oil. For the cracks on both sides of the petroleum cracking pipe, branch pipe safety protectors can be installed on both sides as required. If the oil cracking pipe is installed in the container, the packer can weld the safety protection support frame inside the petroleum cracking tubes. Previous page: How to clean plastic coated copper tubes. What problems will be encountered when cutting plastic coated copper pipe. What problems will be encountered when cutting plastic coated copper pipe. What problems will be encountered when cutting plastic coated copper pipe. When plastic coated copper pipe is cut such as woven cloth and straw mats. In order to better distribute the textile petroleum cracking tubes in the tank, the wound is uneven and cracked. Then I will introduce how to solve these problems. For the disconnection part of plastic coated copper pipe, please fix the equipment with square steel pipes such as vises, and cut it after fixing. In the area to be disconnected, use a towel or soft cloth to crack the oil stain or dirt on the surface of the pipe. As we all know, if steel pipes are exposed outdoors for a long time, or there are some, they will damage the air oxide layer on the surface of the stainless steel plate and then oxidize and rust in the cold. Gas. Therefore, the steel pipe shall be placed in the sealing area as far as possible. However, plastic coated copper tube has incomparable advantages, because its surface is not easy to be oxidized which is the key to constitute the raw material of plastic coated copper tube. The high-precision plastic coated copper pipe has an extremely thin, firm and smooth chromium rich air oxide film on its surface to prevent oxygen molecules from re penetrating and re oxidizing in the air, thus preventing rust. The description of the plastic coated copper pipe shows that the part with weak corrosion resistance of the transition film will produce pitting corrosion reaction due to the self-excited reaction, and the small holes will form highly corrosive aqueous solution. The chloride ion content will accelerate the corrosion rate.

assets.The operation is very convenient. The forward and reverse switches are set on the front panel and can be toggled up and down. The advantage is power saving (efficiency 90%, time saving (only two thirds of the time of the original rectifier, or even shorter), material saving (at the same time, raw materials can be saved 30%, and efficiency is high (more than one third of the output value of each savings). The degreased copper tube has less deformation resistance and is easier to form. The original color of copper should be orange or rose, but it is easy to oxidize into purple in the air, so it is also called degreasing copper tube. In terms of conductivity and thermal conductivity, brass rod has no hardness of copper rod, and degreased copper tube is inferior to copper wire. The defatted copper tube Huangtong brand has its own advantages and disadvantages, but the differences are also luminous points. Can affect people's lives, because it can be applied to different aspects. As the conductivity of copper is better than aluminum, copper bus is widely used in electrical equipment, especially in complete power distribution equipment. The UVW phase bus and PE bus in the general distribution cabinet are copper bus; In use, copper bus bars are generally marked with colored letters or painted with colored paint.

Common defects in copper strip production?

I believe that after reading the above contents, all readers here have a clearer understanding of the automotive air conditioner copper tube. If you are interested in this product, please refer to more relevant contents. Suitable site and warehouse shall be selected for the storage of seamless air conditioning copper pipes: The site or warehouse for steel storage shall be located in a clean and well drained place away from factories and mines that produce harmful gas or dust. With the rapid development of economy, the number of cars is also fast. Nowadays, people can't live without cars. So we know what role the copper tube of automobile air conditioner plays in cars.

Chirila Bangbu.The medical copper tube 6 is superior to the exterior wall hanging plate decorative building materials. It will be affected by microorganisms in the air all year round, the board surface also needs to be treated with interface mortar, otherwise it will cause local hollowing of the insulation layer. How to protect the medical copper tube during installation? The medical copper pipe shall be installed in strict accordance with the installation requirements, the construction process must be strictly required, and do not place heavy objects on the surface.

Handle carefully to prevent damage and scratches. 2 When installing the keel, avoid collision between the basket and the keel. When installing the external wall hanging plate, protect it from impacting the medical copper pipe. 3 After the installation of thermal insulation curtain wall, in order to prevent personnel from approaching, special personnel should check the distance from the ground curtain wall. 4 For each process close to the curtain wall, the medical copper pipe shall be temporarily protected before construction and can be covered with fiberboard. Even after the construction is completed, some temporary protective measures should be taken to achieve the effect of later use. 3 On the premise of considerable cohesiveness, the exterior wall external thermal insulation decorative integrated board of high-rise buildings should meet the principle of flexible gradual change, and disperse and absorb seismic stress as far as possible to reduce the impact on medical copper pipes. 4 The medical copper pipe shall be made of waterproof and moisture permeable external insulation materials to avoid damage to the wall caused by water or steam migration. 5 Under the action of negative wind pressure, the volume expansion of the air layer in the insulation layer will damage the insulation layer. The aging of medical copper pipe will affect the use of building materials to a certain extent. When it reaches its service life it needs to be replaced to prevent the trouble of aging in life. 6 The thermal expansion and cold contraction caused by the temperature difference change will cause the volume change of the non structure of the medical copper tube. Such medical copper tube has a shorter service life than the plate in normal use, when the oil drops on the table and needs regular maintenance according to regulations.

Use the medical copper tube table to eat. Because of the unique of the medical copper tube, it will only stick to the table, but not penetrate the table. Only with a slight wipe of the rag, the oil stains will be easily disappeared. In this case, when cleaning large canteens, the liquidators do not need to spend much effort but are relaxed. They just need to prepare a rag and a basin of clean water, and then carefully scrub it. t2 Medical Copper Tube Company thinks that the medical copper tube table is only made of the surface of the medical copper tube, and its exterior is not made of the medical copper tube. The price is cheaper than the wooden table, which is extremely suitable for a small amount of purchase. The medical copper tube has a natural bright and beautiful feeling. The color is extremely blended, and can stop the very good embellishment and reaction with the color in the surrounding situations. Now, let's understand some STEPs of the appearance processing of medical copper tubes. There are about five different methods for the appearance processing of medical copper tubes. Connect to t2 Medical Copper Tube Company and introduce them to the master. In addition, these methods can also stop the combined processing and create more medical copper tubes with different appearances. No matter which method is used, the following STEPs should be followed. First, before processing, the agreement should be stopped with the manufacturer, and then a sample should be selected as the standard for future consumption. The second part, when using it, we should guarantee that the coils of the base we choose to use and the coils that are not yet used are the third of the same model and batch. If they are used in some construction, such as elevators, we should pay attention to the unexpected selection of materials. In some places with extraordinary contrast, such as weld grinding it is necessary to select the appropriate manufacturing process, how to restore the appearance. Class For the processing of the appearance of some textured t2 medical copper tubes, pay attention to the bias, if the lines used are vertical rather than horizontal, it is not easy to apply the dirty residue on the appearance of t2 medical copper tubes. It is extremely easy when they are clean. When finishing, STEP of the process used should be added, so the cost also needs to be added. Therefore, when selecting the appearance of the processing, t2 Medical Copper Tube Company revealed that Panbo consumers should carefully select according to the situation, and when selecting the planning and design staff, they should have a full understanding of the appearance of t2 Medical Copper Tube. Since the birth of medical copper tube, it has been widely used in food, chemical industry, crude oil, machine manufacturing and other industries for its superior . It is precisely because of this kind of universal needs that people are increasingly demanding for medical copper tubes. Although this kind of situation is basically conducive to the development of the medical copper tube industry. Having said so much, the editor of this website will introduce the most popular technology in the medical copper tube industry -- the medical copper tube appearance fingerprint free disposal punishment technology. Mentioned here, I believe that many enemies have learned the greatest advantages of this kind of technology from the name. However, do you know that this is nothing more than a contrast of significant and abstract advantages. The most one-sided introduction is also my face. The medical copper tube after adopting this kind of technical treatment has a smooth appearance and soft hand feeling, and ordinary dust and impurities are not easy to adhere. Therefore, it is also extremely easy to clean. If the ordinary dust is probably dirt, just wipe it with a wet rag and you will lose the clean and smooth appearance. Because the implementation of this kind of craft is to use electroplating oil to shine the film on the red interior line, so it has the characteristics of being tough and not easily scratched. This prevents the possibility that some slight bumps may damage the medical copper tube. It also allows the medical copper tube to be used twice as quickly. Stop the fingerprint free disposal and punish the medical copper tube after the accident. It also loses great promotion in appearance. As the saying goes, a superior appearance can always leave the best impression. Therefore, compared with the medical copper tube after the punishment and the medical copper tube without the punishment, it can often be welcomed by customers and enemies.Hot rolling and hot expansion. The main processing procedures include the blank sawing process, and the production process of the air conditioning copper pipe in the tower mainly includes cold drawing. Ring furnace heating process, piercing process, pipe rolling process, sizing process, cooling bed process, straightening process, magnetic flux leakage detection process, surface inspection, length measurement and weighing to packaging and warehousing. Key points: yield strength limit: when the external force borne by the air conditioning copper tube sample exceeds the elastic limit of the material, although the stress no longer increases, the sample still has obvious plastic deformation. This phenomenon is called yield, that is, resulting in obvious plastic deformation. The stress when the air conditioning copper pipe yields is called the yield strength limit, and the corresponding S point in the tensile test curve is called the yield point. For air conditioning copper pipes with high plasticity, there will be an obvious yield point on the tensile curve, while for materials with low plasticity, there will be no obvious yield point, so it is difficult to calculate the yield limit according to the external force at the yield point. Therefore, in the tensile test method, it is usually specified that the stress when the gauge length on the specimen produces 0.2% plastic deformation is taken as the conditional yield limit, expressed as 0. The yield limit index can be used as the design basis for requiring that the parts do not produce obvious plastic deformation during operation.