1.5 welding of
1018 stainless
304ti stainlesStainless welded pipe (grade y) gb3280-84 stainless cold plate (grade I)
The competition in stainless steel pipe industry is fierce and gradually intensified. With the flood of fresh brand blood and the downturn of market economy, the development of stainless steel pipe manufacturers is faltering. However, it can be seen from some relevant data that the overall market potential is still great. Stainless steel pipe connection manufacturers should know how to proceed step by step and make steady progress in order to have a chance to win the market.
.Austenitic stainless steel has good resistance to uniform corrosion, but there are still the following problems in local corrosion resistance: intergranular corrosion of austenitic stainless steel. Austenitic stainless steel will have intergranular corrosion when it is kept warm at 450 ~ 850 ℃ or cooled slowly. The higher the carbon content, the greater the tendency of intergranular corrosion. In addition, intergranular corrosion also occurs in the heat affected zone of the weldment. This is due to the precipitation of Cr rich Cr23C6 on the grain boundary. The chromium poor area is formed in the surrounding matrix, which is caused by corrosion of the primary cell. This intergranular corrosion phenomenon also exists in the ferritic stainless steel mentioned above.
SPHDSPHD—& mdash; Hot rolled steel plate and strip for stamping.
.Prepare materials and tools, prepare corresponding materials and tools, and check whether they match and apply.
Air pressure and water pressure test: conduct water pressure test for pressure resistant pipes one by one, the professional stainless steel plate, stainless steel coil, stainless steel belt and stainless steel pipe are strictly tested and the quality is guaranteed. The preferential activities are in progress. Welcome to consult. It is easy to bend, which will affect the production of decorative plate. If the thickness is too large and the steel plate is too heavy,S32750 super duplex stainless steel plate, it will not only increase the cost of the steel plate, but also bring unnecessary difficulties to the operation. At the same time, the allowance that should be left during processing or use of stainless steel plate shall also be considered. The thickness of copper plate is not absolutely consistent, but the thickness of the same steel plate shall be as consistent as possible. Generally, for medium-sized saw plate, the thickness tolerance is 0.05-0.15mm. If the requirements are too strict, the grinding cost will also increase. Generally, it is a structural steel plate with high resistance and high degree. The greater the mechanical damage resistance, the longer the service durability, but the grinding and processing cost is also relatively high.
The rolling of cold drawn (rolled) seamless steel pipe is more complex than that of hot rolled (seamless steel pipe). The first three steps of their production process are basically the same. The difference starts from the fourth step. After the round tube blank is emptied, it needs to be started and annealed. After annealing, pickling shall be carried out with special acid. After pickling, apply oil. Then it is followed by multi pass cold drawing (cold rolling) and special heat treatment. After heat treatment, it will be straightened.
The slab solidified on the surface continues to be rapidly cooled through the secondary cooling section until the core becomes solid, and the whole continuous casting process of stainless steel pipe fittings is completed.
The main function of chromium is the organizational structure of. Chromium has high chemical stability,303 stainless steel welded pipe, can form a passive film on the steel surface, isolate the metal from the outside, protect the steel plate from oxidation and increase the corrosion resistance of the steel plate. After the passivation film, the corrosion resistance decreases.
Affordable price.Standard provisions.
Production process of hot rolled stainless steel strip / coil: 1. Pickling → 2. High temperature rolling → 3. Process → 4. Annealing → 5. Leveling → ⒍ fine cutting → ⒎ packaging → 8. Reach customers.
If the thickness of the steel plate is not enough, the professional stainless steel plate, stainless steel coil, stainless steel belt and stainless steel pipe are strictly tested and the quality is guaranteed. The preferential activities are in progress. Welcome to consult. It is easy to bend, which will affect the production of decorative plate. If the thickness is too large and the steel plate is too heavy, it will not only increase the cost of the steel plate, but also bring unnecessary difficulties to the operation. At the same time, the allowance that should be left during processing or use of stainless steel plate shall also be considered. The thickness of copper plate is not absolutely consistent, but the thickness of the same steel plate shall be as consistent as possible. Generally, for medium-sized saw plate, the thickness tolerance is 0.05-0.15mm. If the requirements are too strict, the grinding cost will also increase. Generally, it is a structural steel plate with high resistance and high degree. The greater the mechanical damage resistance, the longer the service durability, but the grinding and processing cost is also relatively high.
The corrosion resistance of corrosion-resistant stainless steel plate mainly depends on its alloy composition (chromium, nickel, titanium, silicon aluminum, manganese, which mainly acts on chromium. Chromium has high chemical stability, can form a passive film on the steel surface, isolate the metal from the outside, protect the steel plate from oxidation and increase the corrosion resistance of the steel plate. After the passive film, the corrosion resistance decreases.
Good quality.For the length of welding arc, 2 ~ 4mm is better for ordinary steel welding, and ~ 3mm is better for stainless steel welding. If it is too long, the protection effect is not good.
When the stainless steel pipe with solid core welding wire is prefabricated, and the ventilation is very easy. At this time,Price of stainless steel square tube, the blocking plate is usually used to block both sides of the welded junction in the pipe, and the bottom welding is carried out for the protection of ventilation (see Table 1), and the outside is blocked with adhesive cloth.
Mechanical machinability in high-speed machine, the feed rate and cutting speed of alloy are the same as L. If carbonization is adopted, with a density of 93 GCM which is also called 188 stainless steel in the industry. High temperature resistance of 800 ℃, with the characteristics of good processing performance and high toughness, it is widely used in industry furniture decoration industry and food and medical industry.
The two ends of the 6m long steel pipe are mechanically cut, and the pipe end is relatively sharp to prevent direct contact with the sealing ring of the pipe fitting. It is necessary to cut off a small section at both ends of the pipe or grind off the corner edge with a hand grinder and then clamp the pipe fittings.
Origin: domestic and imported (Sweden, Japan, South Korea, South Africa and Taiwan); classified according to the thickness of thin plate (0.2mm-4mm), medium plate (4mm-20mm), thick plate (20mm-60mm) and extra thick plate, according to the production of hot-rolled steel plate and cold-rolled steel