UlanhotFreight elevator type hydraulic lifting platformImprovement of system speed change mechanism

Oil leakage from the oil cylinder: If it is a problem with the sealing ring replace the sealing ring. If there are debris or debris on the oil cylinder, it is recommended to replace it with a new one.

Ensure that there is a suitable power supply at the installation site, and separate maintenance of the distribution box is required. The distribution box should have a leakage switch, and the hydraulic cargo elevator construction site should be equipped with a fire extinguisher to prevent welding operations from causing fires. When selecting a leakage switch, it should be suitable for the operating power.

Ulanhot.Clean the surface of the base and install anchor bolts. If the construction elevator is installed on the floor, use a pad iron under the base screws to increase the force surface between the nut and the floor, in order to reduce the impact of the nut on the floor; Insert steel plate gaskets of different thicknesses between the chassis and the foundation stone at the anchor bolts to adjust the verticality of the guide rail frame; Install three standard sections and measure the verticality of the guide rail frame using a theodolite; After adjusting the verticality of the guide rail frame, tighten the four foundation bolts; Adjust the verticality of the fence door frame as above and press it tightly

Introduction to the unloading lifting platform: The unloading lifting platform is a specialized auxiliary equipment used in conjunction with forklifts for cargo loading and unloading. With it, forklifts can directly drive from the ground into the interior of car compartments for batch loading and unloading operations. The warehouse unloading platform products use manual hydraulic power and do not require power supply. Only one person needs to operate to achieve safe and fast loading and unloading of goods. It can reduce a lot of labor, improve the efficiency of loading and unloading operations, speed up the flow of materials and obtain greater economic benefits.

.The smoothness of the gearbox, gearbox, external meshing gears, and hydraulic oil are all carried out according to the requirements in the smoothness table.

Reason: Manual pump and gear pump have severe oil leakage. Cleaning method: Replace the oil pump sealing ring to clean it. Reason: Gear pump is damaged, which cause electric motors to sweep and produce noise; The cooling fan of the electric motor is damaged or not firmly fixed, resulting in high noise; The electric motor is not firmly fixed and can also cause vibration, producing high noise.

After 10000 hours of operation on the hydraulic lift, major repairs will be carried out to the mechanical and electrical systems.

The safety belt should be inspected before use and a static load test should be conducted regularly (every 6 months). The load for the boarding bridge test is 225 kilograms, and the test time is 5 minutes. After the test, check for deformation, cracks, etc., and keep test records. Unqualified seat belts should be promptly dealt with.

Electrical equipment or component failures. Hydraulic elevator manufacturers tell you that the main reasons for high noise generated by electric motors are: bent or severely worn motor rotors or damaged bearings, which cause electric motors to sweep and produce noise; The cooling fan of the electric motor is damaged or not firmly fixed, resulting in high noise; The electric motor is not firmly fixed and can also cause vibration, producing high noise.

details.Reason: The lowering valve is not tightly closed. Cleaning method: Check if the lowering valve is powered on. If there is no power supply, clear the malfunction of the lowering valve itself or replace the lowering valve. It is necessary to keep the valve of the lowering valve clean and flexible.

When installing,Ulanhot6-meter hydraulic lifting platform, disassembling, and adjusting the rotating mechanism, attention should be paid to ensuring that the middle line is parallel to the middle line of the gear, and its meshing surface is not less than 70%. The meshing clearance should be suitable for the brakes of each mechanism. The clearance between the brake wheels should be regularly checked and adjusted to ensure its flexibility and reliability. There must be no dirt on the friction surface and it must be cleaned with gasoline or diluent.

Remove the hydraulic oil tank filler cap, filter cover, inspection hole, hydraulic oil pipe and other parts to avoid dust when removing the system oil pipe. Clean the disassembled parts before opening them. When disassembling the hydraulic oil tank filler cap, first remove the soil around the tank cap, loosen the tank cap, and remove any remaining debris from the joint (do not rinse with water to prevent water from seeping into the tank). After confirming cleaning, open the tank cap.

Oil leakage is a common malfunction. Due to loose joints or damaged sealing rings, oil leakage may occur. Therefore, this fault can be solved by tightening the oil leakage joint or replacing the damaged sealing ring.

Test method.Surface paint quality: The paint should be smooth and flat, have good adhesion with metal, have uniform color, no bubbles, and there should be no wrinkles, pits, paint leakage, and sagging.

Hydraulic cargo elevator: Only when the load of the hydraulic guide rail type lifting cargo elevator cannot start working, should the pressure of the hydraulic system be checked. If the pressure is below the normal range, the set value of the relief valve should be adjusted. Professional elevator manufacturers have high pressure resistance, good waterproof performance, fire and high temperature resistance, strong overload capacity, corrosion resistance,UlanhotSelf propelled hydraulic lifting platform, radiation resistance, and long service life

The development of elevators is at its peak, as many manufacturers have chosen more multi-story buildings to fully utilize the site, so they also need a device to facilitate the improvement of goods.

Ulanhot.Check valve leakage: If the natural wear of the check valve exceeds the specified value after long-term use, it will cause leakage. Disassemble and clean the check valve, and replace it if necessary.

To consider its capacity, generally mobile equipment takes 2-3 times the high flow rate of pump Z, and fixed equipment takes 3-4 times.

Wholesale manufacturers of hydraulic cargo elevators have found that the market demand for hydraulic cargo elevators is also increasing. More importantly, as well as decoration, hotels logistics, warehouses, supermarkets, etc. are commonly used in these situations, especially in the decoration industry. I have seen many decoration companies use small hydraulic cargo elevators, which are also specially processed and manufactured, and have some differences from the hydraulic cargo elevators we often see. There are significant differences in structure, shape, and height, and the prices of hydraulic cargo elevators also vary. The hydraulic cargo elevators used in the decoration industry have a low lifting height, some only 2 meters, and do not require many materials. He mainly promotes people, not goods, and rarely promotes goods, so the load is small, but not inferior to the use of other hydraulic cargo elevators. He is stable, safe,UlanhotManual hydraulic lifting platform, interpretable, and durable enough to make hydraulic cargo elevators a good helper in the decoration industry. The function of hydraulic cargo elevators is gradually improving with our needs, and the properties we require are different. Wholesale manufacturers of hydraulic cargo elevators also manufacture according to our requirements.