BotanzaMast ty
BotanzaHydraul
BotanzaColumn The product has a sturdy structure, a large load-bearing capacity, smooth lifting, making it an ideal and economical cargo conveying equipment for replacing elevators between low floors. The editor will tell you about the level
The daily maintenance of guide rail type lifting equipment should pay attention to regular inspection and maintenance, eliminate hidden dangers, eliminate faults, and achieve these benefits for improving work efficiency, extending equipment service life, and ensuring the safety performance of the elevator.
Botanza.When using the hydraulic lifting platform, it is also necessary to check for overheating, as this equipment is equipped with a motor. If the motor is overheated, it may cause damage to the motor. However, replacing a motor is relatively expensive. Therefore, during driving or trial operation, if the motor is found to be overheated, it should be stopped immediately, and then the fault that caused the motor to overheat should be checked and eliminated, Only then can the machine continue to be used.
Use a heavy crane to lift the cage and lift it from above the standard section
.Operating cost advantage: Low failure rate. Due to the use of advanced hydraulic systems and good methods, the failure rate of elevator operation can be minimized. Low power consumption: When the hydraulic elevator descends it is driven by the pressure generated by its own weight, which greatly saves energy.
The size of the oil cylinder should be minimized as much as possible while meeting the design requirements. The smaller the size of the oil cylinder the faster the lifting speed.
The second is that the steel will have obvious thermal expansion effect at low temperature. Although this property of steel will be taken into account when designing and manufacturing hydraulic elevators, the steel will have some unstable performance the environment is different after all. Under low conditions, such as hardness increase, toughness decline, etc. At this time, more attention should be paid to the maintenance of equipment to keep key parts to avoid dry grinding.
Regularly check the connection of each part of the hydraulic elevator, and tighten it if there is any looseness. The tightness of the body connecting bolts should be checked when the body is under pressure, and all connecting shafts must have split pins and be sufficient.
The above introduction to common faults of hydraulic boarding bridges can be said to be very detailed. I hope everyone can respond well to various problems after reading it.
Precautions for daily maintenance of hydraulic elevator: Check all hydraulic pipelines and joints of the hydraulic elevator. The pipelines must not be damaged, and the joints must not be loose. All joints must be tightened.
Customer first.Motor does not rotate: The motor is broken, and the manufacturer will handle it. We are a long-term manufacturer of scissor type elevators. Welcome to inquire
The sinking of a cargo elevator is a phenomenon where the table surface drops due to gravity after a certain period of time when it rises to a designated position. Of course, this problem is definitely abnormal. So how can we solve it? The first step is to identify the cause. Below, the editor summarizes the ultimate solution.
The reduction gearbox gearbox, external meshing gear and other parts, as well as the hydraulic oil, are all carried out according to the requirements in the table. Professional scissor lift manufacturer with high prices, service, on-site settlement, and honest operation!
Hydraulic oil should be kept clean and replaced every 6 months; When repairing,Botanza8-meter hydraulic lifting platform, maintaining, and cleaning the elevator, be sure to support the support rod.
Professional is king.The inconsistent rotation axis of the support rod in the middle of the hydraulic lifting platform results in the lifting platform being unable to function properly, causing serious damage to the platform and causing the table to tilt. Please carefully check that the general shear type high-altitude work platform was not strictly tested for tilt before leaving the factory, and was put into the market,BotanzaDouble shear hydraulic lifting platform, causing many accidents. For small enterprises, they are not very concerned about this aspect of tilt detection, This is also why there are such a large number of lifting equipment with this problem. The problems with the oil cylinder and power unit system are often due to insufficient power and substandard oil cylinder quality, which are also very important issues for enterprises themselves.
Everyone is familiar with elevators, especially guide rail elevators, which are used outdoors or indoors. It is inevitable that some small problems will occur after a long period of time. At this point, eliminating hidden dangers, and troubleshooting are beneficial for improving work efficiency, extending equipment service life, the hydraulic oil level should be 40-50 millimeters higher than the bottom of the oil tank. When the color of the hydraulic oil darkens, the oil becomes sticky, or there are foreign objects such as gravel in the oil, the hydraulic oil should be replaced in a timely manner. The hydraulic system of the lifting platform should be checked for hydraulic and pipeline connections. If the pipeline is damaged, it should be replaced immediately; When there is looseness in the connection part,BotanzaHydraulic lifting platform frame, tighten the pipe joint.
In our daily life, hydraulic cargo elevators are increasingly widely used and loved by customers. As a lifting tool, the maintenance of hydraulic cargo elevators should not be careless. Below, which can cause uneven force distribution during the delivery of hydraulic oil, resulting in uneven surface conditions. It is recommended to carefully check whether the delivery pipe is smooth.