Mako6063 aluminum barWhat problems should be paid attention to during operation-World information network

In addition, brass has a unique sound, so the gongs, cymbals, bells, as well as the western brass instruments, are all made of brass, which is a kind of non-ferrous metal processing bar, with good processing performance and high conductivity. It is mainly divided into copper tube (copper zinc alloy, cheaper). The manufacturing principle of copper tube: All elements without exception reduce the conductivity and thermal conductivity of the copper bar. All elements are dissolved in the copper bar, causing lattice distortion of the copper bar, causing wave dispersion when free electrons flow in a directional direction, increasing the resistivity. On the contrary, which has little impact on the conductivity and thermal conductivity of the copper bar, Special attention should be paid to the fact that the solid solubility of some elements in the copper bar decreases sharply with the decrease of temperature. The precipitation of simple substances and metal compounds can not only strengthen the copper bar alloy by solid solution and dispersion, but also reduce the conductivity slightly. This is an important alloying principle for the study of high-strength and high conductivity alloys. Here, it should be pointed out that the alloy composed of iron, silicon, chromium and copper bar is a very important high-strength and high conductivity alloy; As the influence of alloy elements on the properties of copper bars is superposition, CoCrZr series alloys are * high-strength and high conductivity alloys; It is not easy to heat. Semi continuous casting copper tube has excellent conductivity. Copper tube has excellent conductivity. Alloy copper to ensure safety and fatigue resistance. Tin phosphor bronze jack adopts hard wire electrical structure without rivet joint or conflict contact, which can ensure excellent touch, wear resistance, and will not produce sparks when stamping. It is used for medium speed and heavy load bearings. The working temperature is up to 250 ° C, and the active centering is insensitive to deflection. The bearing force is uniform, and the bearing capacity is high. It can withstand radial load and self lubrication without protection. The company is a manufacturer specializing in the production of various bronze tubes, bronze rods, bronze plates and profiled bronze profiles. Technical advantages: The maximum diameter of bronze bars and pipes can reach 300mm, while that of plates can reach 600mm. The wall thickness of bronze tube can be as small as 4mm. The copper tube is a common bronze material. The aluminum content of copper tube generally does not exceed 5%. Sometimes, nickel, manganese and other elements are added to further improve the performance. It has high strength and good wear resistance. It is used for copper sleeves and wear resistant parts with high strength. The outstanding feature of t2 copper tube is its good wear resistance. The difference between copper tube and copper tube The copper tube is a copper based alloy with aluminum as the main alloy element. The copper tube is a copper based alloy with tin as the main alloy element. The mechanical properties of copper tube are higher than that of copper tube. The aluminum content of the copper tube in practical application is between 5% and 12%, the aluminum content is 5%, and the 7% copper tube has good plasticity and is suitable for cold working.

When I need to use more quantity, what are the factors that cause the surface corrosion of copper tubes. Introduce the factors that cause the surface corrosion of copper tubes. Surface pollution: The oil, dust, acid, alkali, salt, etc. attached to the surface of the workpiece will be converted into corrosion medium under certain conditions, which will react with some components in the stainless steel parts to produce chemical corrosion and rust.

Mako.Save materials and total cost, stability and performance, and can save maintenance.

Pay attention to the following points when using flame heating brazing: the selection of welding materials The filler metal is wire or rod with a diameter of about 35mm. The material is: the melting temperature of wire 221 is about 0905 ℃. Its chemical composition is FB10 The composition is 2331% H3BO3 and 6071% KBF The joint form of brazed copper pipe is mostly plug-in. Before cleaning the brazed copper pipe before welding, the edge of the pipe mouth must be corrected and deburred to ensure that the pipe mouth is free of cracks or other defects. And clean the surface of the inserted part. After the red copper pipe is assembled by tack welding, it shall be fixed by tack welding. The number, size and height of tack welds shall be symmetrically and evenly distributed along the circumference from top to bottom, left to right, and the tack welds shall be melted into the whole weld during brazing. When brazing the copper pipe, the flat angle position shall be used as far as possible to ensure continuous welding. Select the appropriate welding torch according to the size of the pipe joint. The flame of the former Han Dynasty should be neutral, because the oxidation flame has high oxygen content, which is easy to oxidize copper and cause cracks; The carbonization flame contains free hydrogen, the pipe joints shall be heated evenly the flame shall be perpendicular to the heating surface, and the base metal shall be heated as quickly as possible to avoid excessive temperature and heating time of the through pipe joints. During the brazing of degreased copper tube, the brazing seam and filler metal shall be under the protection of flame. In addition, and the weldment shall not be moved before the brazing seam has solidified. After natural cooling after welding, hot water or wet cloth shall be used to wipe the brazing seam and remove welding slag to improve corrosion resistance and reliability of post welding inspection.

.However, for some important parts, it is also considered that the yield ratio should be smaller to improve their safety and reliability. However, at this time, the utilization rate of materials is also low. Common sense: copper pipes for air conditioners are mainly used for conveying liquid, structure and steam transmission of steam boilers, including the transmission of high-temperature and high-pressure steam; Structural pipe, widely used in aviation, automobile, tractor and other industrial sectors; Pipe for petroleum industry, mainly used for oil and gas exploitation, such as casing, drill pipe and tubing, and pipe for petroleum refining and processing; Pipe for mechanical manufacturing, which is used to manufacture the race of ball bearing, the plunger rotating shaft and body of air pump and hydraulic pump; High pressure vessel, used for manufacturing bottles, boilers, shells, copper pipes for air conditioners are mainly used in three aspects in practical applications. First medical copper pipes are widely used in industrial plants, high-rise civil buildings, municipal engineering, oil platforms, bridges, railway vehicles and other fields. Because of their good plasticity, high structural stability and strong resistance to natural disasters, they are particularly suitable for building structures in earthquake prone areas. Second, the air conditioning copper pipe has high tensile strength and toughness, high buildings, bridges and other steel structures have good cold bending performance and welding performance, and the section size and surface quality are well controlled, so it is widely used in vehicle manufacturing, large bridge construction, mechanical manufacturing, industrial plant components and many other industries. Third, air conditioning copper pipes are mainly used to make transmission line towers, construction crane towers, elevator supports,Mako310s stainless steel round steel, etc. The idea is to use weather resistant steel when making iron towers to meet the service conditions of both normal temperature and low temperature. PPM pressure roll piercer used for air conditioning copper pipe tapping rolling is not replaced by inclined roll piercer used for square steel billet. The advantage of the conical piercer is that it has the consequence of rotary euphemism casting and the of restraining the shear deformation of the square circumference and the square back. Therefore, it can prevent the defects outside the steel pipe. It can be used for the perforation of agricultural materials especially not for the reaming and fat wall perforation. When using a general piercer, the wall thickness/pitch diameter ratio (T/D limit is about 6%, while when using a square cone piercer, the T/D limit can be 2%. Tianjin Precision Steel Tube Factory will give you a brief introduction.

Plastic coated copper pipe is one of the safe carbon fiber products. Its specific content is a new structural composite building decoration material that can be produced according to the development trend of production and manufacturing by using a glass fiber as the synergist and resin as the adhesive based on the application of full intelligent technical automatic control system equipment.

The large diameter coated medical copper tube can deform to prevent the risk of ductile damage; The medical copper tube has sufficient plastic deformation, and the medical copper tube is capable of deformation. It is stipulated that the plastic deformation and ductility of medical copper tubes are good. Good plastic deformation can ensure that the structure can have significant deformation before destruction. In some peak periods of the structure, the tectonic stress will be redistributed, which makes the tectonic stress spread gently. Good ductility indicates that under dynamic and static loads, more kinetic energy should be digested and absorbed when the structure is destroyed, which is the risk water of ductile destruction. For the structures with plastic deformation design scheme and the structures in disaster areas, the size of the deformation working capacity of medical copper tubes has a particularly critical practical significance. 3 Production and processing characteristics of medical copper tubes. It can be integrated with cold and heat treatment, and will not cause great harm to compressive strength, plastic deformation and ductility due to such production and processing. 4 Weldability of medical copper tube. The welding of medical copper tube is a rapid heating and cooling process. The metal materials in the welding and heat affected zone need to go through heating and melting, physical reflection, cooling and crystallization, and solid state change in a very short time. The industry trend is a kind of medical copper tube. Because there is no seam in the middle it has more advantages in strength. Medical copper tubes have many different s in practical application, and each different will make the medical copper tube work well.Advantages of medical copper tubes: compared with solid copper tubes such as round steel, medical copper tubes have the same tensile strength, torsional strength, and tensile strength, and their net weight is relatively light. One is plastic copper tubes cut for social and economic development, which are widely used in the production and processing of spare parts and mechanical parts, such as oil drilling equipment, rotating shafts, bicycle frames, and steel medical copper tube frames used in engineering construction. This kind of welded medical red copper pipe is developed under the special conditions that the temperature is all over and the composition is extremely unbalanced. After this kind of welding, it can produce detailed welding joints to maintain special performance indicators, which is the specified weldability. 5 Performance of medical copper tube. It refers to the service life of medical copper tube. The production and processing of annular parts with medical copper tubes can achieve the utilization rate of raw materials, simplify the production process, save raw materials and manufacturing hours, such as needle bearing throw rings, hydraulic jack sleeves, etc. At present, medical copper tubes have been widely used for production and processing. Disadvantages of medical copper tubes: medical copper tubes are also indispensable raw materials for various strategies. Drums must be produced and processed by medical copper tubes. Medical copper tubes can be divided into round medical copper tubes and profiled steel according to their different cross-sectional areas. Due to the large circle area under the same diameter specification, the annular pipe can be used to transport many large diameter medical copper pipes. Large diameter coated medical copper pipes are widely used in tap water, petroleum, chemical industry, communication, power, thus ensuring the purity and hygiene of the fluid. The temperature range from - 40 ℃ to+80 ℃ can be used alternately in cold and hot cycles, without aging and cracking, so it can be used in cold areas and other harsh conditions. When processing medical copper tubes, the medical copper tube factory will use pickling, which is an indispensable part of most medical copper tubes, Pickling process is the treatment after removing surface oxide scale (Carbon steel - stainless steel - lime saponified phosphorus, butter oil, copper and aluminum pipes - and the old ones, and then wire drawing processing. Then what are the points to be noted when washing? 1 When washing the medical copper pipes, they need to be carried out in the flowing clear water tank so as to avoid secondary pollution. When washing, the medical copper pipes need to be fully immersed in water. At this time, the sling should be relaxed, and it can be lifted up and down three to four times. If the medical copper tube is not acid resistant, the surface may be oxide and oil, and the phosphating solution cannot remove nuclear energy. However, after acid washing of medical copper tubes, the water in the medical copper tube needs to be cleaned to avoid water corrosion and oxidation of the medical copper tube. Therefore, it is necessary to carry out solvent treatment as soon as possible. 4 When the medical copper tube is washed, the iron salt content must be controlled within a certain range, and it cannot exceed the standard, otherwise the medical copper tube may be damaged.

Mako6063 aluminum barWhat problems should be paid attention to during operation

The operation is very convenient. The forward and reverse switches are set on the front panel and can be toggled up and down. The advantage is power saving (efficiency 90%, time saving (only two thirds of the time of the original rectifier, or even shorter), raw materials can be saved 30%, and efficiency is high (more than one third of the output value of each savings). The degreased copper tube has less deformation resistance and is easier to form. The original color of copper should be orange or rose but it is easy to oxidize into purple in the air, so it is also called degreasing copper tube. In terms of conductivity and thermal conductivity, brass rod has no hardness of copper rod, and degreased copper tube is inferior to copper wire. The defatted copper tube Huangtong brand has its own advantages and disadvantages, but the differences are also luminous points. Can affect people's lives, because it can be applied to different aspects. As the conductivity of copper is better than aluminum, copper bus is widely used in electrical equipment, especially in complete power distribution equipment. The UVW phase bus and PE bus in the general distribution cabinet are copper bus; In use, copper bus bars are generally marked with colored letters or painted with colored paint.

Today, the price of tube billets is up and down. At present, Jiangxin hot rolling is 3700 yuan, continuous casting 3600 yuan is down 100 yuan, Dongfang hot rolling 4020 yuan is down 30 yuan, Luli hot rolling 3670 yuan is down 50 yuan, Tiangang hot rolling 3830 yuan is down 50 yuan, production is stopped in mid January, Weigang hot rolling 3740 yuan is up 150 yuan, continuous casting 3590 yuan is up 90 yuan, Huaigang 4150 yuan is up 50 yuan, Zhongtian 4100 yuan, Changqiang 4050 yuan, Linggang 4140 yuan.

Air conditioning copper pipe is a common metal material in daily work of industrial production. The conductivity,Mako6061 aluminum bar, heat conduction and corrosion resistance are excellent, and the W shape trend of air conditioning copper pipe is depressed due to the high copper content. Good machinability, the cutting machine should carry out calibration and other operations. You can try to use scrap metal first to prevent machine problems from causing me to cut off defective products.

Installation requirements.When I need to use more quantity, what are the factors that cause the surface corrosion of copper tubes. Introduce the factors that cause the surface corrosion of copper tubes. Surface pollution: The oil, dust, acid, alkali, salt, etc. attached to the surface of the workpiece will be converted into corrosion medium under certain conditions, which will react with some components in the stainless steel parts to produce chemical corrosion and rust.

The process flow of plastic coated copper pipe: the settlement price of 904l stainless steel plate is on the high side, and the price is stable. 904l stainless steel plate: last Friday, the steel plant made all the orders. As for the guide price the market price rose slightly on Monday due to the positive sentiment after the festival. The working efficiency of t2 copper pipe after the expansion from Tuesday to Friday should be the same. Between the upper and lower clamping groove bodies of the alloy pipe to be flared, the end of the alloy pipe to be flared faces the flaring die, extends a certain length (depending on the flaring length), and then drives the upper clamping groove body to move down through the oil cylinder. Then, the flaring hydraulic cylinder drives the flaring die to the alloy pipe, so that the t2 copper pipe flaring die will stretch the alloy pipe port to expand its inner diameter in the alloy pipe port at the front end. The length of flared section can be 20200 mm. How to solve the crack of plastic coated copper pipe? How to solve the common fault of crack in case of improper operation during the construction of plastic coated copper pipe project? If it is not handled in time, there is a serious risk. Therefore, I will carry out practical operations in strict accordance with the engineering construction specifications and requirements related to immediacy, find more practical welding processes and then ensure the welding quality of electric welding. If we continue to develop plastic coated copper pipe materials under such circumstances, we will find that the price difference of plastic coated copper pipe with low-grade anti rust materials is different, and there are many reasons for the price difference. First, there are significant differences in production. Although it is made of stainless steel the plastic coated copper pipe can be compared with the plastic coated copper pipe on the market.

Mako6063 aluminum barWhat problems should be paid attention to during operation

The material cost of medical copper tube will not be less than 40 yuan. The better the material is, the higher the price will be. It is called &one cent, one cent&. Moreover, in addition to the production and operation costs, labor costs, factory rent, etc., you must pay attention to the quotation below 45 yuan/square. Medical copper tubes are more and more widely used in the decoration of building exterior walls. In cold cities in the north, medical copper tubes can play a very good role in decoration and insulation. With the continuous progress of science and technology, the quality and firmness of medical copper tubes have been improved. However, as long as the decoration materials are used, they will inevitably crack during installation and construction. As time goes by, there will be aging to varying degrees in daily life. Next, Zhongsheng Thermal Insulation Technology will introduce how to prevent the cracking of medical copper tubes and how to prevent the aging of medical t2 copper tubes? Let's talk about these two issues. How to prevent cracking of medical copper pipes To avoid cracks, buildings should be fully insulated, including awnings and other components. Through the quality and construction methods of external medical copper pipes, the construction quality can reach By reducing the ratio of the linear expansion coefficient of external thermal insulation materials of the building structure to the linear expansion coefficient of materials such as external decoration leveling mortar and external decoration surface, gradual changes will occur between medical copper pipes layer by layer, and the stress can be flexibly released, To prevent cracking. How to prevent medical copper tube from aging? The insulation layer of high-rise buildings shall have fire resistance , and shall have the characteristics of preventing fire spread and releasing smoke or toxic gas in case of fire. The strength and volume of materials shall not be reduced too much, and the surface shall not burst or collapse. Medical copper tube Medical copper tube is a new type of plate which is popular in China in recent years. It has many advantages, such as good heat preservation fire insulation, sound insulation, convenient construction, beautiful appearance, etc., and is deeply welcomed by the industry. The medical copper pipe may fall during use. In order to reduce the occurrence of this kind of phenomenon, Jinan Zhongsheng Thermal Insulation Technology made a detailed ysis. Next, we will introduce the reasons for the fall of the external wall of the medical copper pipe and how to protect the medical copper pipe during installation. Reasons for the fall of the external wall of the medical copper pipe The medical copper pipe was not firmly fixed and moved, forming a push-pull effect, causing local hollowing of the insulation layer, and long-term water seepage after cracks, leading to the fall of the insulation layer. 3 At the connection between the concrete beam column and the masonry, the medical copper pipe is easy to fall off due to the deformation of the masonry. 4 Scaffold holes are not solid, forming insulation layer, and local base course is not firm and damaged. 5 The surface load of the medical copper tube is too large, or the anti negative wind pressure measures are unreasonable.

reform.In future work, try to protect the surface of the copper tube.

Defects in metal: various defects in the red copper strip, such as impurity atoms, vacancies, internal (grain boundary) dislocations and external surfaces cause lattice distortion and cause electron wave scattering, which affects conductivity.

In addition, quartz sand is used as sand intercalation layer on the long distance uniform pavement in the middle of chemical fiber. Its wall thickness and structure are reasonable, and the plastic coated copper pipe laying process stipulates that the plastic coated copper pipe is a non-metallic material pipe with light quality, high strength and corrosion resistance. The glass fiber with epoxy resin based weight relief is coiled on the rotating hollow floor step by step according to the processing technology. It can make full use of the efficacy of raw materials, achieve the goal of applying compressive strength, improve the strength and stiffness, and ensure the reliability and stability of t2 copper tube. FRP sand pipe is accepted by many customers because of its excellent resistance to solvent erosion, light weight, high strength, non fouling, strong durability long service life compared with ordinary seamless steel pipe, low comprehensive project cost, convenient installation, reliability and other advantages. Plastic coated copper pipe is used in: gray and black metallurgy industry, nonferrous plate metallurgy industry, power industry, coal engineering, petroleum industry, chemical industry, electromechanical engineering industry, cotton textile, vehicle and motorcycle processing and manufacturing industry, railway line for industrial production, engineering construction, light industry, food industry, electronic industry, power, culture and art, sports culture and game entertainment, agriculture and animal husbandry commercial services, Diagnosis, treatment and health and its national defense and civilian industries.

Mako.Plastic coated copper pipe is a kind of non-metallic material pipe with light weight, high strength and corrosion resistance. The plastic coated copper pipe is made of glass fiber with resin base weight, which is wound on the rotating hollow floor step by step according to the processing technology regulations, and the stone sand is laid on the ground evenly for a long distance in the middle of the chemical fiber as the intermediate weathering layer. The price quotations of plastic coated copper pipes with different thicknesses are also different. Here, we will explain the factors that determine the thickness of the plastic coated copper pipe design scheme. Appearance and specification of mpp cable duct 1 Color: generally orange red, other colors can be implemented according to the contract of both parties. 2 Appearance quality: The inner and outer walls of the pipe fittings shall be smooth, clean and even, and shall be free of steam bubbles, cracks, cracks, molting, dents, residues, dissolved discoloration lines and uneven colors. The inner holes of the pipe shall be laser cut and leveled and vertical to the pipe centerline. The inner holes shall be smooth and free of burrs. Specification: The length of pipe fittings is generally 6000 or 9000mm, which can also be negotiated by both parties. The specification error shall conform to dl/t801; The bending degree of the hose shall not exceed 1% of the nominal pressure. Some key points in the process of embedding plastic coated copper pipe: the embedding process of plastic coated copper pipe is very worthy of great attention. Although the actual operation in the process of embedding is relatively simple, there may be many key points. Pay special attention to the leveling and straightness of the road surface when threading, In other words, if the road surface is seriously uneven, it is seriously affected by external forces. Relevant countermeasures must be taken, and fine sand and dirt should also be prohibited from seeping into the pipe during the burial process, so as to diligently maintain its compliance with the regulations during the burial process. The process of embedding the plastic coated copper pipe involves the problem of marking. In fact, the marking that can be carried out according to this marking in the process of maintenance and repair is the key inspection index value of the commodity. If it is found that there is a problem with a certain section of cable, it is only necessary to find matching marks for immediate maintenance. Number of layers of cloth stacking: all layers are made strictly according to the design scheme, without additional construction, which increases the cost. 2 Resin: high temperature resistance, not easy to deform under stress. Plastic coated copper pipes are generally assembled from high-quality SMC water tank plates. Its characteristic is that it can select food grade stainless steel resin. Therefore, in view of the good water body, clean up the natural environment and zero pollution, the commodity development trend has certain characteristics such as high compressive strength, light weight corrosion resistance, beautiful and generous appearance design scheme, and more convenient management methods in maintenance. Cloth quality: the specification of cloth surface is the same, pure platinum cloth is thick, and it is thick with blended cloth or pure old coarse cloth. The thickness of fiberglass filament winding: our products are high-tech support points of fiberglass anti-corrosion ring, which ensures the bearing pressure of the products. In addition, if you must select the thickened type, you can yze the vertical cross type difficult winding when winding the winding machine, until the thickness and compressive strength of the thickened type are basically achieved.

Now let me talk about the damages that are easy to occur on the surface of the copper tube. In order to prevent the accumulation of process agents or products and/or dirt, scratches and other rough surfaces, mechanical cleaning must be carried out. If the copper pipe is heated to a certain high temperature in the air during welding or grinding, chromium oxide heat return color will appear on both sides, lower surface and bottom of the weld. The color after tempering is thinner than that of the oxidation protective film, and is clearly visible. The color depends on the thickness. The thicker oxide can be found in the rainbow color, blue, the chromium content on the metal surface will and the corrosion resistance of these areas will. In this case, it is not only necessary to heat temper the color and other oxide layers, but also to clean the chromium poor metal layer under it. Free iron on the surface of t2 copper tube will rust, causing corrosion of stainless steel. Therefore, the powder that must float can usually be removed together with the dust. Some are very sticky and must be treated as embedded iron. In addition to dust, there are many surface iron sources, including cleaning with ordinary carbon steel wire brush and shot peening with sand, glass beads or other abrasives previously used on ordinary carbon steel,Makobrass tube, low alloy steel or cast iron, or regrinding non stainless steel products attached to copper pipe components and equipment. If there is no protection during cutting or hoisting, slings and iron on the working surface can easily be embedded or dirty the surface. The copper tube shall be boiled in boiling water for 30 seconds before cold treatment. The effective internal stress is about 15%, and the residual austenite reaches the effect. Then, the cold treatment can be carried out as usual. Of course, the second suggestion is to choose the normal treatment at minus 60 degrees, and then conduct deep cooling at minus 120 degrees. The lower the treatment temperature is, the retained austenite will be rapidly transformed into martensite, but it cannot be transformed. Through experiments, it can be found that there will be about 2% of retained austenite. At this time, retained retained austenite can achieve a certain buffer effect. After cold treatment the air conditioning copper pipes need to be taken out and put into hot water for heating, which can effectively heat about 40% of the cold treatment stress. Tempering and cold treatment should be carried out as soon as possible after gradual heating, and most of them can avoid cracks as soon as possible, so as to ensure that the products will not deform in later use and facilitate daily storage. The transformation characteristics of the area of each layer of the copper tube during empty drawing affect the asymmetry of the deformation of the metal material. One of its characteristics is that the natural widening of each layer along the wall thickness is not consistent. Of course, the internal surface layer of the copper tube is larger, and the natural widening of the middle layers is slow from the external layer to the internal surface layer.The technical level of degreasing copper tube for mechanical equipment With the substantial improvement of the manufacturing level of mechanical equipment and the degree of control automation in China, there is still some gap between the technical level of domestic degreasing copper tube production line and the products of foreign counterparts. After years of reform and opening up. The quality of all aspects of degreased copper pipe has also risen by several grades, significantly narrowing the quality gap with the imported production line. The aluminum hose production line and aluminum can production line developed and produced by the company break the technological monopoly of foreign companies, can provide stable and reliable production equipment for domestic and international markets, and make great contributions to the aluminum packaging industry. With the continuous improvement of people's living standards, there will be more and more demand for degreased copper tube products, and its market potential is huge. Problems such as incomplete penetration, deformation, cracks and air holes are easy to occur during the fusion welding of degreased copper tubes. Compared with fusion welding, wood is not melted during brazing, which reduces the impact of large thermal conductivity of base metal on welding quality, prevents the formation of incomplete penetration, reduces the tendency to produce pores and cracks, and ensures the performance of weld. Because the base metal is not melted the structure and properties of the base metal are almost unchanged, so that the original service properties of the base metal can be maintained.

For the production and processing of sculpted copper tubes, the sheet metal shall be first opened in the sheet metal workshop according to the dimensions shown in the drawings, which is commonly referred to as opening. Then cut the corners of these open sheets according to the height of the edge, and then use the bending machine to form the edge according to the drawing forming diagram. The shaped copper pipe shall also be installed with reinforcing ribs as required, and the four corners of the shaped plate shall be welded well. The welded parts shall be sent to the grinding workshop, and the spraying surface shall be polished and the welding interface shall be polished and leveled. The polished modeling copper pipe is then sent to the spraying workshop for processing. Before spraying, the surface of the sculpted copper pipe shall be chrome treated and the process hole shall be drilled, so as to ensure that the sculpted copper pipe can be hung on the spraying line well, and the painting can be smooth without flow marks, and the color is consistent without color difference. After that according to customer demand, the qualified products are pasted with protective film and bound with bubble film or wooden box.