ZhangjiakouHan
ZhangjiakouMob
ryan HydraulicThe contact of the travel switch must be firmly opened and closed, and the contact crater should be polished in a timely manner.
The classification of lifting platforms is as follows: they are divided into mobile lifting platforms, automatic lifting platforms, hydraulic lifting platforms, folding arm lifting platforms, and sleeve type lifting platforms according to their different modes of movement.
Zhangjiakou.The lifting platform is mainly used for the up and down transportation of goods between various working floors, but it may slowly rise during use. When the equipment is working, it mainly uses hydraulic motors to drive hydraulic pumps. So what is the reason for the slow movement? Professional elevator manufacturer with large quantity and excellent quality at a reasonable price. Fire resistant, waterproof, high temperature resistant, sturdy and durable, safe and reliable
The hydraulic oil used in the system has the same brand, and the oil temperature is between 45~80 ℃. Use a large flow rate to remove impurities from the system as much as possible. The hydraulic system needs to be cleaned repeatedly three times or more, and after each cleaning, the system should be drained while the oil is hot. After cleaning, clean the filter and add new oil after using a new filter element.
.Due to damage to the gear pump of the lifting cargo elevator equipment and no pressure lifting. Replace the gear pump.
When disassembling and adjusting the reverse organization of the equipment, attention should be paid to ensuring that the centerline of the reverse organization reducer is parallel to the centerline of the gear, and its meshing surface is not less than 70%. The meshing gap should be appropriate.
The hydraulic lifting platform is a manually movable type, and the lifting power of the platform is a two machine or three-phase power supply. It has manual and electric power, stable lifting, and easy operation, and are mainly used in factories, government agencies, commercial stores and the construction and decoration industry.
Check valve leakage: If the natural wear of the check valve exceeds the specified value after long-term use, it will cause leakage. Disassemble and clean the check valve, and replace it if necessary.
The load of goods and the tonnage of goods transported at once also affect the lifting speed. The optimal value for transporting goods on a lifting platform is speed. If it is too heavy, it will affect the speed. The above is the knowledge about adjusting the lifting speed of hydraulic cargo elevators hoping to be helpful to everyone. Long term improvement: The manufacturer has a complete range of products, excellent quality, and discounted prices
To consider its capacity, generally mobile equipment takes 2-3 times the high flow rate of pump Z, and fixed equipment takes 3-4 times.
Quality department.When using an electric mobile scissor lifting platform outdoors, if the wind force exceeds level 5,ZhangjiakouScissor fork hydraulic lifting platform,ZhangjiakouHydraulic lifting platform, the wind ropes at the four corners of the hydraulic lift platform should be tightened and fixed, and the support legs should be reinforced for protection and stability to avoid safety accidents caused by excessive swinging of the electric lifting platform
The guide rail type elevator has a structure of a straight top oil cylinder. The linear operation of the oil cylinder pulls the transmission chain, driving the lifting of the table to complete the operation. The guide rail type elevator is a popular form of cargo elevator in recent years, with the advantages of higher lifting height,ZhangjiakouScissor fork hydraulic lifting platform, stable operation, and simple maintenance compared to the scissor fork type elevator.
Car mounted lifting platform: The car mounted lifting platform is designed to improve the mobility of the lifting platform by fixing it to a transport vehicle or truck. It receives power from the car engine and achieves the lifting function of the car mounted lifting platform. To adapt to high-altitude operations inside and outside the factory area.
An inverter can also generate high noise. When the power supply voltage is lower than 85% of the rated voltage, the short circuit ring of the iron core of the device breaks, the surface of the magnetic yoke and armature is skewed, and the device will produce; Buzz&# quo; Noise.
Management Department.The cylinder head oil seal is too tight or the rod is bent, which can also cause noise during movement due to other forces. At this point, the oil seal or straightening rod must be replaced in a timely manner.
The hydraulic elevator has no counterweight device, which improves the utilization rate of the well surface.
Selection of the location of the loading and unloading lifting platform In order to reduce the cost of material handling, the location of the platform should be selected to minimize the distance of the handling tools and vehicles in the factory. It is much easier to move a fully loaded transport vehicle to a designated location outside the building than to transport the loaded materials one by one to the designated location indoors. When selecting a platform location, full consideration should be given to the production process and operational needs of the factory. There are two modes of platform layout: merging: loading and unloading on the same platform.
Zhangjiakou.Electrical equipment or component failures. Hydraulic elevator manufacturers tell you that the main reasons for high noise generated by electric motors are: bent or severely worn motor rotors, or damaged bearings which cause electric motors to sweep and produce noise; The cooling fan of the electric motor is damaged or not firmly fixed, resulting in high noise; The electric motor is not firmly fixed and can also cause vibration, producing high noise.
The hydraulic lifting platform often checks the connection status of each part, and if there is any looseness, it should be tightened. The connection bolts of the machine body should be checked for tightness when the elevator body is under pressure (the compression condition can be formed by rotating the arm). All connecting shafts need to have split pins and need to be fully opened.
The hydraulic lifting platform often checks the connection status of each part, and if there is any looseness, it should be tightened. The connection bolts of the machine body should be checked for tightness when the elevator body is under pressure (the compression condition can be formed by rotating the arm). All connecting shafts need to have split pins and need to be fully opened.