BotanzaSelf hy
BotanzaFixed hProtective device: In case of power or oil circuit failure, there should be a safety rope to prevent the workbench from falling out of control. (Allow controlled descent)
After 5000 hours of elevator operation, carry out medium maintenance on the mechanical and electrical systems.
Botanza.In winter when working outdoors at heights below minus 10 degrees Celsius, heating rest areas should be set up near the construction area if necessary. Heating equipment should be managed by dedicated personnel and attention should be paid to fire prevention.
The hydraulic elevator overflow valve can also generate high noise. When air is mixed in hydraulic oil,BotanzaDouble fork hydraulic lifting platform, the overflow valve is stuck or severely worn, the spring of the overflow valve is fatigued and deformed,BotanzaMobile hydraulic lifting platform, resulting in unstable pressure regulation of the overflow valve, it is easy to cause the pilot valve performance of the overflow valve to be partially stable, causing air to vibrate inside the pilot valve and generate noise. So we need to regularly clean the overflow valve. When the overflow valve is damaged or severely worn, it should be replaced.
.The classification of lifting platforms is as follows: they are divided into mobile lifting platforms, automatic lifting platforms, hydraulic lifting platforms, folding arm lifting platforms, and sleeve type lifting platforms according to their different modes of movement.
Regularly check all wires and cables for damage. It is necessary to wrap and replace the damaged parts in a timely manner.
Stability: The workbench should evenly withstand 125% of the MAX load capacity and be stable at the MAX elevation.
The optional configurations of a fixed lifting platform include manual hydraulic power, rolling or motorized roller tracks, organ type safety protective covers, manual or motorized rotating workbenches,BotanzaSelf hydraulic lifting platform, hydraulic overturning workbenches, safety support rods to prevent the lifting platform from falling stainless steel safety nets, electric or hydraulic lifting platform walking power systems and universal ball countertops.
The hydraulic pump also has an impact on the flow rate of hydraulic oil. If the hydraulic pump is used for a long time, it is also prone to problems. When the speed of the hydraulic lifting table slows down, it is necessary to check whether the oil supply of the hydraulic pump is firm and firm.
The contact of the travel switch must be firmly opened and closed, and the contact crater should be polished in a timely manner.
Sampling inspection.Protective device: In case of power or oil circuit failure, there should be a safety rope to prevent the workbench from falling out of control. (Allow controlled descent)
When the hydraulic system malfunctions, the hydraulic elevator may experience problems with the hydraulic pump, motor, valve, and hydraulic installation after repairing the hydraulic system, which can easily cause vibration and generate significant noise.
Voltage too low: Measure the starter voltage, with an allowable fluctuation range of± 10%.
Do you know the classification of simple cargo elevator lifting platforms? The manufacturer of the hydraulic cargo elevator is here to inform you.
Service first.There are many reasons for unstable workbench descent, such as overload, unstable support, severe eccentric load, hydraulic oil impurities, etc. In response to the above reasons, it can be solved by reducing the load, adjusting the center of gravity of the load, and replacing hydraulic oil wholesale for hydraulic cargo elevators.
What are the requirements for the pit? This type of cargo elevator only needs 15-30 centimeters and does not require too much space. The installation of scissor type hydraulic cargo elevators is different from that of guide rail type hydraulic cargo elevators. The scissor lift cargo elevator has a large load-bearing capacity, and the pit depth needs to be set at around 40-70 centimeters. It can also be designed according to customer on-site needs.
Do you know the classification of simple cargo elevator lifting platforms? The manufacturer of the hydraulic cargo elevator is here to inform you.
Botanza.Aluminum alloy elevators are different from other forms. This type of elevator is made of aluminum alloy material, which is lightweight and has a more beautiful appearance. The disadvantage is that it has a light load capacity and is only suitable for simple high-altitude maintenance work, and can only provide support for 1-2 people.
The precautions to consider when selecting a hydraulic lift oil tank include: considering the structure of the oil tank, the partition in the traditional oil tank cannot settle dirt. A vertical partition should be installed along the longitudinal axis of the oil tank, with a space left between one end of the partition and the end plate of the oil tank to connect the gaps on both sides of the partition. The inlet and outlet of the hydraulic pump are arranged on both sides of the partition at the disconnected end, so that the distance Z between the inlet and return oil is far, The hydraulic oil tank has more heat dissipation effect.
The use of cleaning oil and the brand used in the system