0 200× 200×0～ 0 220× 220×0～ 0 250× 250×0～ 0 280× 280×0～ 0 300× 300×0～ 0 320× 320×0～ 0 350× 350×0～ 0 380× 380×0～ 0 400× 400×0～ 0 420× 420×0～ 0 450× 450×0～ 0 480× 480×0～ 0 500× 500×Standard treatment of steps for preventing oxidation of 0 ~ 0 square tube square tube is a kind of metallic maintenance. The main components are iron and zinc. It is easy to have redox reaction in the air. Once the reaction occurs, many new substances have taken place, and the original characteristics have changed. However, in order to maintain the original relevant characteristics, anti-oxidation treatment is required. The direct reason is to prevent the square tube from reacting with the oxygen in the air, which is the way to isolate the oxygen in the air. Today, this article makes a relatively standardized treatment on the relevant steps to prevent oxidation of square tubes: the key depends on what kind of antirust paint you use. 1. If you use epoxy zinc rich or iron rich antirust paint, you can directly spray fluorocarbon paint on it; 2 if alkyd antirust or red lead is used, it shall be cleaned with paint remover and sprayed with epoxy zinc rich or iron rich antirust paint again before fluorocarbon paint can be sprayed.
The tensile test is to make q355b into a sample, pull the sample to fracture on the tensile testing machine, and then measure one or more mechanical properties. Usually only tensile strength, yield strength, elongation after fracture and reduction of area are measured. Tensile test is the basic mechanical property test of metal materials. Almost all metal materials have specified tensile test as long as they have requirements for mechanical properties. Especially for those materials whose shape is not convenient for hardness test, tensile test has become the only means to test mechanical properties.
Trentay attempt.Hardness hardness is a pointer to measure the hardness and softness of metal materials. At present, the hardness method is commonly used to measure the hardness in production. It uses the indenter with fixed geometry to measure the hardness value of the metal material surface tested under fixed load according to the degree of hardness.
Square tube failure. When the pipeline is erected, it is necessary to do a good job or directly use the square pipe. The reason for the corrosion of the pipeline is that the layer of the pipeline is damaged. Once the layer is separated from the pipe surface, it will naturally cause failure.
.Therefore, the drawing process of square tube is quite meticulous. For a long time, square tube, square tube, seamless square tube, galvanized square tube, galvanized tube and other brand products are provided with complete designated products and quality assurance. In the process of continuous development, square tube has also been processed more rigorously.
The standard quantity of combustible and nonflammable square pipes is gbt97-1 (gbt97-199). The representative material is l245-l4 pipeline steel. Professional square pipes, square rectangular pipes, seamless square pipes, galvanized square pipes and galvanized pipes are of high quality and low price. They are fire-resistant, waterproof, high temperature resistant, durable, safe and reliable. They are mainly used to transport combustible and nonflammable fluids with high requirements.
At present, square tubes also have many good properties, strong corrosion resistance and heat resistance, and are widely used in many scientific and technological fields. Therefore, even so, square rectangular tubes, seamless square tubes, galvanized square tubes and galvanized tubes are welcome to waste merchants, industries, enterprises and power departments to visit and negotiate! Oxidation will also occur on the surface of square tubes after long-term use. What should we do if oxidation occurs? Let me give you a detailed introduction on how to remove square tubes Oxide scale.
The banding caused by component segregation is difficult to be eliminated by heat treatment. Generally, normalizing can reduce this segregation to a certain extent. Generally, normalizing can correct the segregation to the allowable level. If the banding is serious, it can be improved by multiple normalizing. It is reliable to conduct high-temperature diffusion annealing first and then normalize again, which can completely eliminate the strip, but the cost will be very high, which is difficult to achieve for the steel plate due to the surface quality.
A complete range of products.D. do not cut your hands boring, mm; L0 -- original gauge length of sample, mm. Reduction of area (& psi;) in the tensile test, the percentage between the large reduction of the cross-sectional area at the reduced diameter and the original cross-sectional area after the specimen is broken is called the reduction of area. In & psi; Expressed in%. The calculation formula is as follows: where: S0 -- original cross-sectional area of the sample, mm2; S1 -- small cross-sectional area at the reduced diameter after sample breaking, normalizing can correct the segregation to the allowable level. If the banding is serious, it can be improved by multiple normalizing. It is reliable to conduct high-temperature diffusion annealing first and then normalize again, which can completely eliminate the strip, but the cost will be very high, which is difficult to achieve for the steel plate due to the surface quality.
Soft blowing treatment of molten steel after calcium treatment can reduce residual inclusions in molten steel and better wrap MNS around al20 CAS and other cores.
technical service.Square tube is made of steel ingot or solid tube blank through perforation, and then made by hot rolling, cold rolling or cold drawing. Square pipe plays an important role in steel pipe industry.
Square tube is a very good steel in economic construction. There are many kinds and principles of cold drawing. You may still have a lot of insufficient understanding of the cold drawing principle of each other's pipe. Next, I'll lead you to learn its cold drawing principle.
Functional index analysis of square tube - mechanical function of plastic square tube.
Trentay attempt.In the process of processing, the processing temperature is the key. Professional square tube, square tube, seamless square tube, galvanized square tube and galvanized tube have advanced technology, strict detection more affordable price and more preferential price. Consultation is welcome. It must be noted that the blank heating should be uniform. Perforation has a great impact on the quality. The perforation temperature of blank varies according to different materials, generally around 1200 ℃.
Cutting: 1 to be fast, no teeth, or whether the cutting line is flat, the starch taste of oil affects the quality of dishes. First choose to cut potatoes with less sharp bottom, so when you cut, it's easy to leave the corner of the side end.
Square tube is the main type of square tube. It is also very popular in the square tube market. There are many people doing this kind of thing so there are many in the competition. The future market potential is huge. We should grasp this information well. In addition, we must learn about relevant maintenance and repair!