Costa-RicaRect
San-RafaelHow Process flow of square tube drawing: because the size of the die hole of the square tube drawing is smaller than the outer diameter of the tube in front of the drawing, in order to make the front end of the square tube pass through the die hole smoothly, so that the clamp jaw of the drawing trolley can the head of the square tube, it is necessary to sharpen the head of the square tube before drawing. Therefore, the end of the square tube with a fixed length should be heated in the slit heating furnace, It is generally 150 ~ 200mm, and the heating temperature is between 750 ~ 900 ℃ according to different wall thickness. Then use 75 ~ 300kg air hammer to sharpen and grind the head of the square pipe. Generally,Costa-Rica6. How much is a ton of galvanized pipe, the square pipe with diameter less than 22mm can be sharpened by rotary forging hammer or roll forging machine.
Except for the thickening of the wall thickness the corner size and edge flatness of the square pipe are uniform
Costa-Rica.The local heat release in the welding process of square tube can reduce the heat affected zone, avoid the micro of thermal sensitive materials, and maintain the properties of materials.
The square tube can be sprayed with fluorocarbon paint, which needs some treatment before spraying.
.The tensile test is to make q355b into a sample, and then measure one or more mechanical properties. Usually, only tensile strength, yield strength, elongation after fracture and reduction of area are measured. Tensile test is the basic mechanical property test of metal materials. Almost all metal materials have specified tensile test as long as they have requirements for mechanical properties. Especially for those materials whose shape is not convenient for hardness test, tensile test has become the only means to test mechanical properties.
Chemical polishing: less investment in processing equipment, high speed, high efficiency and good durability. Its defects are poor brightness, gas overflow, demand for ventilation equipment and difficult heating. It is suitable for processing small batch of disordered parts and products with low brightness demand for small parts.
Functional index analysis of square tube - mechanical function of plastic square tube.
When the square tube is covered, the surface of the square tube shall be ventilated to avoid the collection of water vapor on the surface due to difficult volatilization.
The reason why the surface of fake and shoddy materials is easy to crack is that its blank is adobe with many air holes. During the cooling process, the adobe has cracks due to the action of thermal stress, and there are cracks after rolling.
The purpose of heat is to prevent the generation of cold cracks. Cold crack is directly related to carbon equivalent. Therefore, it is necessary to distinguish the carbon equivalent of the q355b square tube, and the carbon equivalent of the q355b square tube is the same. If the carbon equivalent of Q345 is less than 0.3%, it can be said that the weldability is OK. Generally speaking, the cold crack increases when the carbon equivalent is 0.4%.
Workshop cost.The test can be carried out under cold and hot conditions. If the test temperature is not specified the test shall be carried out under normal temperature, but not lower than - 10 ℃.
Hardness test is to determine the hardness of seamless q355b square pipe by slowly pressing a hard indenter on the sample surface according to the specified conditions, and then testing the indentation depth or size.
After perforation, the round tube blank is successively rolled by cross rolling, the steel pipe enters the cooling tower for water spray cooling. After cooling, the steel pipe will be straightened. After straightening the steel pipe
All seamless q355b square tubes shall be tested for mechanical properties. Mechanical property tests are mainly divided into two categories: tensile test and hardness test.
Sincere service.Structure: used as pile driving pipe and bridge; Pipes for wharf,Costa-RicaHow much is a galvanized steel pipe, road, building structure, etc. It is mainly used as petroleum geological drilling pipe cracking pipe for petrochemical industry, boiler pipe, bearing pipe, tractor and aviation, etc.
Section shape classification square tubes are classified according to section shape: simple section square tubes & mdash& mdash; Square tube, rectangular tube and complex section square tube & mdash& mdash; Surface treatment classification of flower shaped square pipe, open square pipe,Costa-Rica60 galvanized round pipe, electro galvanized square pipe, oil coated square pipe and pickling square pipe according to surface treatment. Square pipe is classified according to purpose & mdash& mdash; Square tubes for decoration machine tools and equipment, machinery industry, chemical industry, steel structure, shipbuilding, automobile, steel beam and column and special purpose are classified by wall thickness & mdash& mdash; Super square tube, square tube and thin-walled square tube plasticity refers to the ability of metal materials to produce plastic deformation (deformation) without deformation under load.
Square tubes have a good performance in practical application. When we choose square tubes in practice, we should choose them according to their characteristics. We have different types of square tubes in different fields. What is the difference between the characteristics of square tubes and ordinary steel tubes? Let's introduce them today to let us have a deeper understanding of each other's tubes.
Costa-Rica.How to specify the yield point of square tube: if the stress decreases, the upper and lower yield points shall be distinguished. The unit of yield point is nmm2 (MPa
Square tube with complex section: flower shaped square tube, open square tube, corrugated square tube and special-shaped square tube.
How about the tensile strength of square pipe: square pipe has good tensile strength, tensile strength and sufficient toughness, which makes square pipe stand out in the field of steel pipe. The square tube has great advantages in high temperature, high pressure and even high strength environment. What are its characteristics? We analyze it one by one: tensile strength (& sigma; b) the strong force (FB) borne by the sample during tensile breaking, and the stress (& sigma;) obtained from the original cross-sectional area (so) of the sample is called tensile strength (& sigma; b), and the unit is nmm2 (MPA).