Q355b welded pipeMaterial shielding mechanism

Generally, the wall thickness of the rolled pipe is 20mm and the outer diameter is 450-3000mm. It is rolled, welded, formed, butted and rolled directly from the steel plate. It has the advantages of short processing time fast delivery and low cost. The rolled pipe is mainly used for hot-rolled thick wall coils such as pipes, billboard and columns. The thickness of the hot-rolled thick wall coil is generally greater than 20mm and the outer diameter is 450-3000mm. The hot-rolled thick wall coil is rolled under the heating of the steel plate Welding, forming, deburring, defect detection and delivery. Sometimes the wall thickness is relatively thick and secondary heating is required. The feature is that the outer diameter tolerance is small Uniform wall thickness. It is important that the hot rolled thick wall coil will not damage the properties of raw materials. The disadvantages of hot roll thick wall rolling pipe are long processing time and. Hot rolled thick wall coils are widely used: cylinder, hydraulic, bridge, roller table, etc.

In short, hot coiling refers to heating to coil the steel plate. Its meaning shall be determined with cold rolled steel pipe.

.The parts with continuous acoustic flaw detection marks on the weld shall be rechecked by manual ultrasonic and X-ray. If there are defects, after repair, they shall be subject to nondestructive inspection again until it is confirmed that the butt weld of strip steel and the pipe of T-joint intersecting with spiral weld have all passed the X-ray television or film. Each steel plate coil has passed the hydrostatic test, and the pressure adopts radial sealing. The test pressure and time are strictly controlled by the microcomputer detection device of steel plate rolling pipe water pressure. Why are there two longitudinal welds in the same pipe section of rolling pipe?

In progress, welcome to consult. Large diameter welded pipe, etc.

.The detection of thick wall coiled pipe is mainly ultrasonic flaw detector, and the longitudinal weld on the same cylinder section of coiled pipe should not be more than two. Generally, the production process of thick wall coiled pipe can be divided into cold drawing and hot rolling. The production process of cold-rolled seamless steel pipe is generally more complex than hot rolling. Roll sizing test shall be carried out for the pipe blank first. If the surface does not respond to the crack, the round pipe shall be cut by a cutter and cut into a blank with a length of about meters. However, when entering the annealing process, acid shall be used for annealing, and attention shall be paid to whether a large number of bubbles are generated on the surface. If a large number of bubbles are generated, it indicates that the quality of steel pipe can not meet the response standard. In appearance, the cold-rolled seamless steel pipe is shorter than the hot-rolled seamless steel pipe, and its wall thickness is generally smaller than that of the hot-rolled seamless steel pipe, but the surface is brighter than that of the thick wall seamless steel pipe. There is not too much roughness on the surface, and there are not too many burrs in the diameter. The thick wall coiled pipe is a powerful manufacturer, quotation, honest operation, genuine and of the same quality. The thick wall coiled pipe is available from stock, with complete specifications,. The group of butt welds of coiled pipe shall be flush. When the nominal diameter is greater than, back sealing welding shall be carried out in the pipe. During pipe rolling processing, the surface damage of the plate shall be prevented. The factory has perfect steel plate coil, thick wall coil, T-shaped welding coil, flaw detection welding coil, 16Mn coil, Q345B coil, thick wall coil, coil, t-welded coil, flaw detection welded coil, 16Mn coil and Q345B coil shall be carried out in strict accordance with ISO9001:2000 international quality management standards.

Thick wall coiled pipe is a kind of familiar steel. It is widely used in construction and pipeline industry because of its durable performance and excellent quality. Have we known about the packaging process of the frequently used steel? With the development of domestic economic situation and the acceleration of welding and casting trend, the advantages of NC cutting are gradually recognized. NC cutting not only greatly improves the rate of plate and product quality, but also improves the working environment and labor efficiency. At present, the NC cutting machines used in the thick wall coil processing industry are mainly flame and ordinary plasma cutting machines, but pure flame cutting can not meet the needs of modern production. At present, most NC cutting machines are NC plasma cutting machines. This type of cutting machine can meet the needs of thick wall coiled pipe plate processing and thick wall coiled pipe parts processing, so the demand will be greater and greater, but there is still a very obvious gap with foreign countries, which is mainly reflected in: 90% of the developed thick wall coiled pipe processing industry is digital control cutting machine, and only 10% is manual cutting; The CNC cutting machine only accounts for part of the total blanking. 10%, of which the proportion of NC plasma cutting is small. Professional hot rolled steel pipe, large diameter thick wall rolling pipe, thick wall straight seam rolling pipe, steel casing, rolling pipe factory to ensure quality, service and quality. Your satisfaction is our pursuit! Welcome to inquire. In industrial production, thick wall coil thermal cutting generally includes gas cutting, plasma cutting, laser cutting, plasma cutting has a wider cutting range than gas cutting More efficient. Fine plasma cutting technology is close to laser cutting in material cutting surface quality, but the cost is much lower than laser cutting. Therefore, since the successful development of the United States in the mid-1950s, plasma cutting has developed rapidly. With the rapid development of computer and digital technology, NC cutting is also developing, which improves the machining accuracy. Save materials

The steel plate coil adopts the secondary forming process. When rolling, first bend both ends of the steel plate, and the diameter shall be less than the diameter of the coiled pipe. Then adjust the bed pressure, rolling two to three times steel pipe coiled pipe welding and strengthening the rolling pipe joint, long-term rolling pipe Q235B coil pipe, Q345B coil pipe, large diameter thin wall tube, large diameter heavy wall coil pipe, stainless steel coil pipe, 16MN coil pipe and other brand products, designated products are complete, quality assurance. Then transported to the welding platform for welding.

Meet the following requirements: 1. The longitudinal joint of butt joint shall not be greater than 10% of the wall thickness plus 2mm, and shall not be greater than 3mm. 2. The longitudinal joint of joint 200mm away from the pipe end shall not be greater than 2mm. 3. Other parts shall not be greater than 1mm. 4. The vertical deviation between the end face of coiled pipe and the center line shall not be greater than percent of the outer diameter of pipe and shall not be greater than 3mm. The straightness deviation shall not exceed 1mm / m. 5 the weld cannot be double-sided molded coiled pipe. When the nominal diameter is greater than or equal to 600mm it is recommended to seal and seal in the pipe. In order to obtain better uniform cleanliness and roughness distribution, the particle size and proportion design of rinse agent is very important. The roughness is too large, which may cause the anti-corrosion layer to become thinner at the peak of the cloud path. At the same time, because the cloud path is too deep, bubbles are easy to form in the process, which seriously affects the performance of the layer.

When the coil pipe is butt welded, the corresponding parts shall be flushed to. When the nominal diameter is larger than the inner seal, the bottom seal welding shall be carried out. During pipe rolling treatment, it shall be protected.

Cold rolled thick wall continuous pipe is similar to cold rolled thick wall continuous pipe, with wall thickness of 20mm and outer diameter of 450-3000mm. Steel plate is directly rolled, welded, butted and reinforced. Cold rolled thick wall pipe has the characteristics of short processing time, fast delivery and low cost. Cold rolled thick wall pipe is mainly used for: pipe, billboard, column, etc.

Service first.Welding voltage because the welding arc is conical,Q235B large diameter thick wall welded pipe, and the welding voltage directly affects the length of the arc. Therefore, the production process of thick wall coiled pipe can be divided into cold drawing and hot rolling. The production process of cold rolled seamless steel pipe is generally more complex than hot rolling. Roll sizing test shall be carried out for the pipe blank first. If the surface does not respond to the crack, the round pipe shall be cut by cutting machine to cut the blank with a length of about meters. However, when entering the annealing process, acid shall be used for annealing, and attention shall be paid to whether a large number of bubbles are generated on the surface. If a large number of bubbles are generated, it indicates that the quality of steel pipe can not meet the response standard. In appearance, the cold-rolled seamless steel pipe is shorter than the hot-rolled seamless steel pipe, and its wall thickness is generally smaller than that of the hot-rolled seamless steel pipe, but the surface is brighter than that of the thick wall seamless steel pipe. There is not too much roughness on the surface, and there are not too many burrs in the diameter. The thick wall coiled pipe is a powerful manufacturer quotation, honest operation, genuine and of the same quality. The thick wall coiled pipe is available from stock, with complete specifications,. With the increase of welding voltage, the arc length increases, the moving range of arc spots expands, the weld pool widens, and a wider weld formation will be obtained. If welding is carried out in a horizontal position, it will only change the width of the weld without affecting the edge transition of the weld. However the external welding of spiral welded pipe is carried out on the slope, and the molten weld metal will flow laterally under the action of gravity. We specialize in providing hot-rolled steel pipes, large-diameter thick wall coils, thick wall straight seam coils, the wider the molten pool is, the more serious the trend of lateral flow of weld metal will be, * which will eventually lead to the bias flow of weld metal.

It has advantages and quality. The weld reinforcement obtained is increased, the weld formation is deteriorated and the edge transition is poor.

In the process we mentioned, we need to explain each process, such as groove. We need to compact both sides of the steel plate with indenter, so as to avoid the formation of peach shaped mouth in the rolling pipe.

The wall thickness of hot coil thick wall continuous pipe is generally greater than 20mm, and the outer diameter range is 450-3000mm. Hot rolled thick wall continuous pipe is rolled, welded, formed, reinforced, flaw detected and delivered under the condition of steel plate heating. Sometimes the wall thickness is very special and needs secondary heating. It is characterized by small outer diameter tolerance and uniform wall thickness. The main reason is that the hot rolled thick wall continuous pipe will not damage the performance of raw materials. The disadvantages of hot rolled thick wall continuous pipe are long processing time and high cost. Hot rolled thick wall pipe is widely used: oil cylinder, bridge, roll, thick wall continuous pipe has the disadvantages of low cost, fast delivery, breaking the fixed specification of seamless steel pipe and so on. Thick wall coil is welded by bending steel plate or steel strip. According to the weld form, it is divided into straight welded pipe and spiral welded pipe. It can be divided into ordinary welded pipe, galvanized welded pipe, oxygen blowing welded pipe, wire sleeve, metric welded pipe, idler pipe, deep well pump pipe, automobile pipe, transformer pipe, development and service. It has long been specialized in hot-rolled steel pipe welded special-shaped pipe and spiral welded pipe. It is a special product manufacturing enterprise integrating research, large-diameter thick wall rolling pipe, steel casing and rolling pipe factory. Continuous pipe is committed to producing all kinds of circumferential seam and longitudinal circumferential continuous pipe and penstock, and is reformed on the basis of the same specification and model of traditional rolling equipment. The function of parameters of coil welded steel pipe equipment is improved by 30%, which fills the gap that can not be produced by traditional rolling equipment. It can produce steel pipes with diameter of more than 400 and wall thickness of 8-100mm. The main materials are q23 q34 20, 16Mn, 16Mn etc. the product standards are GB / t50205-200,Q355b large diameter thick wall welded pipe, GB / t3092-2001, etc. the products are widely used in petroleum, chemical industry, natural gas transmission, pile driving, urban water supply, gas supply and other projects.

Direct material.1 carbon structural steel: q215-a, q215-a. & middot; F,Q215-B,Q215-B· F,Q235-AQ235-A· F,Q235-B,Q235-B· F. Q235-c ordinary carbon steel: B2 BY2 B2F by2f B3 by3 B3F by3f a2ay2 a2f ay2f A3 ay3 A3F ay3f2 high quality carbon steel: 10 15 20 transmission shaft steel 3 low alloy structural steel: 123mn 16Mn 19mn 08ti 10ti15ti4 special purpose steel plates are stacked in the open air to prevent rain from causing steel plates. The oxide scale falling off the surface of steel plates is easy to turn into blocks or clusters and adhere to steel plates or crimping rollers, When repeatedly pressed, the coiled pipe forms pit defects.

The automation and mechanization level of large-diameter steel coil is not high, which requires a lot of manual treatment. The main problem of large-diameter coiled pipe is welding. As long as the flaw detection can be carried out, the delivery can be carried out. The relevant requirements are broader than other products.

Weld inspection is necessary to detect the weld quality of steel coil pipe. After welding, all the welds are tested by on-line continuous ultrasonic automatic flaw detector to ensure the NDT coverage of the welds. If there are defects it will automatically alarm and spray marks, and the production will adjust the process parameters at any time to eliminate the defects in time.

.The arc length of the coil calibration template shall be 1 / 6 ~ I of the circumference of the pipe / the gap between the template and the pipe. What is the manganese content of the straight seam coil? Q345B coil, manganese is a common element in structural steel. Manganese in carbon steel is mainly added to the steel water as deoxidizer in the steelmaking process, usually in the range of 0.3-0.8%. In low alloy steel manganese is a mixed alloy element, and the manganese content in 16Mn steel and 15MnV steel is 2-6%.

First, select the specification and put forward the pipe, such as 90 & deg; Elbow, which can calculate the curvature to calculate the 90 DEG of the long material; Elbow, and then cut with the length as the fixed length.

Generally, the wall thickness of coiled pipe is 20mm and the outer diameter is 450-