ShoprandWelded galvanized pipeWeak stability and poor price

announcer:hp256HP158312377 release time:2021-10-31 12:49:58

At the same time,ShoprandWholesale hot dip galvanized square pipe, hanging heating shall be carried out during heating to reduce quenching deformation. For high-precision guide rail, gas nitriding or ion nitriding shall be carried out to reduce deformation; Square tubes have outstanding performance in all aspects of performance. We will also test them in this regard when making square tubes more durable. What outstanding performance do square tubes have in mechanical properties? Next I'll introduce it to you.

Q355b square pipe for mining fluid transportation, Standard No.: gbt14291-2000. The representative material is Q235 grade B steel. It is mainly used for straight seam q355b square pipe for mine air pressure, drainage and shaft gas drainage.

Shoprand.Among them, q355b square tube is divided into: (a) by process & mdash& mdash; Arc welded square pipe, resistance welded square pipe (high frequency and low frequency), gas welded square pipe and furnace welded square pipe (b) are divided by weld & mdash& mdash; Straight welded square pipe

It is recommended that the galvanized surface be primed with epoxy zinc yellow primer.

.The advantages of real bending are small reverse, accurate forming, and as long as the roll shape is accurate, the R of inner corner forming is more accurate. The disadvantage of solid bending is that it has tensile thinning effect. The actual bending will produce tension at the bending point, the cost of surface treatment is still relatively high, so it is very important to select appropriate treatment. Only by selecting the right treatment can the coating quality of square pipe be well guaranteed.

The other is designed with deformation angle, which can be regarded as 180 DEG from round tube to square tube; To 90 & deg; The bending deformation of angle, so the deformation angle & theta; It can accurately reflect the deformation degree of corners and edges. In the design process, considering the influence of dimensional accuracy and metal work hardening, the distribution of deformation angle is usually larger at the beginning and middle passes, and then gradually decreases. In the pass formed directly by arc intersection, the fillet part of the pipe blank cannot be filled with the pass, so the pass perimeter is different from that of the pipe blank. In order to ensure the dimensional accuracy, the fillet part of the pass needs to be corrected and calculated. Therefore, this method has higher design accuracy than other methods. However, due to the large amount of iterative calculation, this method is more suitable for pass design by computer. If you use a frame that deforms both horizontally and vertically you can directly use the deformation angle & theta; Pass design.

Functional index analysis of square tube - commonly used are square tube Brinell angle (HB), Rockwell angle (HRC) and Vickers angle (HV). Angle is a gauge needle to weigh the soft and hard level of metal data. The angle method is rarely used to determine the internal angle in the current life. It uses the metal data surface tested under the fixed load of the indenter with a certain number and shape to determine its angle value according to the level of the object.

reform.In fact, the casting cleaning is not just shot blasting. For large parts, the drum sand cleaning is carried out first, the riser of the casting is cut off and rolled in the drum, and the square tubes collide with each other in the drum to remove most of the sand on the surface before shot blasting or shot blasting.

When we understand the causes of defects in the drawing process of q355b square tube, we should constantly improve the technology in the subsequent production process, so that we can reduce the occurrence of defects.

The welding sequence is to reduce deformation. The welding sequence of rectangular butt welding shall adopt layered and symmetrical skip welding from the middle to both sides according to the following principles. The welding deformation is smaller than that of straight through welding, which is conducive to the dispersion and release of stress and avoid complex stress in weldments. During straight through welding, the narrow plastic deformation zone formed at the beginning of welding only occurs once. Moreover, due to continuous welding, the heat input is large, the heating area is large, and the plastic deformation area caused by compression is large, so the shrinkage deformation after welding is very large. In case of layered and segmented skip welding, the section of each layer is very small, and the heat required is small, and each layer is divided into several sections for skip welding. Each welding section basically re establishes the secondary temperature field on the cold steel plate, and a narrow plastic deformation zone appears each time. Therefore,ShoprandQ420d square tube, the average width of the plastic deformation zone (i.e. the size of transverse shrinkage) is smaller than that of the corresponding layered straight through welding, and the longitudinal shrinkage is also smaller, The welding deformation is smaller than that of continuous filling.


ShoprandWelded galvanized pipeWeak stability and poor price



The raw material for rolling square tube is round tube blank. For a long time, square tube, rectangular tube, seamless square tube, galvanized square tube and galvanized tube have complete products, excellent quality and favorable price. The round tube embryo shall be cut and processed by cutting machine, and the blank with a growth of about 1m shall be brought to the furnace for heating. The billet is sent to the furnace for heating at a temperature of about 1200 degrees Celsius. The fuel is hydrogen or acetylene. The temperature in the furnace is the key problem. After the round tube billet is discharged from the furnace, it should be pierced through the pressure piercer. Generally, the more common piercer is the conical roll piercer. This piercer has high production efficiency, good product quality, large perforation expansion and can wear a variety of steel grades.

assets.Reach or even exceed the level of resistance welding cold formed square pipe. The size of R angle is generally between 2-3 times of the wall thickness. R angle square pipe of the size required by customers can also be produced according to customers' needs; Square pipe is a kind of long steel with hollow section and no joints around. It is a square pipe formed by four sides of seamless pipe mold. Square pipe has hollow section, professional square pipe, square rectangular pipe, seamless square pipe, galvanized square pipe, galvanized square pipe strict inspection and quality assurance. The preferential activity is in progress. Welcome to consult. A large number of pipes are used for conveying fluid. They are mainly used in conveying, Medium and low pressure, high pressure boiler tubes, heat exchange tubes,ShoprandGalvanized square pipe as beam, gas, oil and other industries. It is stronger than welded and will not crack.

After chemical pickling, the square tube can be well protected by electrolysis. These are simple ways to prolong the service life of the square tube, We only need to treat according to these, so that the square tube can bring us great help in the use process. The cold galvanized square tube is the principle of cold galvanizing on the square tube used to make the square tube have corrosion performance. Different from hot-dip galvanizing, cold galvanizing coating is mainly carried out according to the electrochemical principle. Therefore, resulting in electrode potential difference, so the steel surface treatment requirements are very high.

The inclusions in the square tube treated with calcium can be denatured well, and the morphology of sulfide in the rolled stock is also improved.

Shoprand.The researcher's test before using the strip thinning drawing also confirmed that using the strip thinning drawing can greatly reduce the large value of tangential residual stress of the drawn parts and effectively prevent the occurrence of longitudinal cracking. According to different deformation degree and original sheet thickness, if & psi; If n is too small, the deformation stress will increase sharply, resulting in the fracture of the bottom of the drawing part.

At the same time the heating temperature and heating time will also have a great impact on the performance of square tube. The heating of square tube blank is the key process to ensure that the square tube blank has enough plasticity and complete the smooth perforation. If the heating temperature is too high or the heating time is too long, the billet of the square tube will be burned and decarburized and even the chemical composition of the square tube will be unqualified (unqualified carbon content), which is easy to cause batch quality problems and seriously affect the product qualification rate.

General shot blasting is used for square tube with regular shape. Several polishing heads are up, down, left and right, with high efficiency and little pollution.