Q235B large di
Q235B large diThe inner diameter of 1800mm steel plate coiled pipe elbow is 1800mm, the bending radius is also 1800mm four bends, the material thickness is 4mm, and the bending is 90 & deg;.
The steel plate or strip is bent and then welded to form a thick wall coil. According to the welding form,16Mn thick wall coiled pipe, it is divided into straight seam welded pipe and spiral welded pipe. It is divided into ordinary welded pipe, galvanized welded pipe, oxygen blowing welded pipe, wire sleeve, metric welded pipe, rolling pipe, deep well pump pipe, automobile pipe, transformer pipe, welded thin-wall pipe, longitudinal ring coil pipe and steel pressure pipe, and is modified according to similar specifications of traditional rolling equipment. The function of increasing the parameters of spiral steel pipe equipment by 30% fills the gap that the original traditional rolling equipment can not produce. It can produce steel pipes with a diameter of 400 or more and a wall thickness of 8-100mm. The material mainly includes q23 q34 20#, 16 manganese, 16 manganese capacity, GB / t3092-2001, etc. The products are widely used in petroleum, chemicals, natural gas transportation, pile driving, urban water supply, heating, gas supply and other projects.
.The process coat of the coil pipe is made of high-density polyethylene, which has extremely high mechanical strength and excellent corrosion resistance, and can protect the coil from external factors during use. The outer sleeve shall be added with antioxidant, ultraviolet stabilizer and carbon black. The polyethylene outer sleeve is easy to age, such as stored in the open air Place the cover and stack away from high heat source and fire source. After making the coiled pipe, it is forbidden to be exposed to the sun and quench, otherwise the polyethylene outer pipe is easy to crack, affecting the product performance and service life.
Main technical measures for low hardening trend
.The effect of antirust oil on thick wall coiled pipe is antirust effect, which can make the thick wall coiled pipe as smooth as new for a long time and reduce the external corrosion to it. It can also increase its sealing performance and ensure that there will be no problems when transporting fluid. In addition, it has moisture-proof performance, uses antirust oil to isolate the direct air of thick wall welded pipe, so it has little chance of being changed by the external situation,45# reel, which increases its stable performance and safer use.
Deviation reel as follows (unit: mm): nominal diameter & amp; amp; lt; 800 800 to 1200 1300 to 1600 1700 to 2400 2600 to 3000 perimeter Deviation & plusmn; 5± 7± 9± 11± The ovality is 1% of the outer diameter and the quality of no more than 4 steel plate coils is greatly affected by the weld size, welding wire shape and position parameters, flux flow, flux process performance and formed joint.
It should be noted that in practice, it is difficult to achieve the ideal proportion of metal sand and metal ball in the rinsing agent, because the hard and brittle metal sand has a higher crushing rate than the metal ball. For this reason, the new rinse agent is added to the cleaning machine, and the amount of metal sand is usually the same in the new rinse agent.
The rolling pipe production technology requires that the rolling pipe weld is a double-sided weld, two longitudinal welds are allowed, and the weld spacing exceeds 300 mm. The welding appearance and quality standard shall not be lower than the level standard in the welding specification.
Executive standard for steel plate rounding: structural tube gb8162-2008 fluid tube gb8163-2008 low and medium pressure boiler tube gb3087-2008 high pressure boiler tube GB5310-2008 special tube for chemical fertilizer GB 79-2000 petroleum cracking tube gb9948-88 steel plate rounding production process: tube blank & mdash& mdash; Inspection & mdash& mdash; Peel & mdash& mdash; Inspection & mdash& mdash; Heating & mdash& mdash; Perforation & mdash& mdash; Pickling & mdash& mdash; Grinding & mdash& mdash;Air drying & mdash& mdash; Welding head & mdash& mdash; Cold drawing & mdash& mdash;& mdash;& mdash; Pickling and passivation & mdash& mdash; Inspection & mdash& mdash; Cold rolling & mdash& mdash; Degreasing & mdash& mdash; Cutting head & mdash& mdash; Air drying & mdash& mdash; Internal polishing & mdash& mdash; External polishing & mdash& mdash; Inspection & mdash& mdash; Identification & mdash& mdash; Process flow inspection of finished product packaging industrial pipe & mdash& mdash; Peel & mdash& mdash; Inspection & mdash& mdash; Heating & mdash& mdash; Perforation & mdash& mdash; Pickling & mdash& mdash; Mushroom trimming & mdash& mdash;Air drying & mdash& mdash; Welding head & mdash& mdash; Cold drawing & mdash& mdash; Solution treatment & mdash& mdash; Pickling & mdash& mdash; Pickling and passivation & mdash& mdash; Formula of steel plate rolling weight: [(outer diameter wall thickness) * wall thickness] * 0.02466 = kg / M (weight per meter)
In short, the use standard of coiled steel pipe is very important and the above points can be reasonably explained. For the information of our rolled steel pipe, let's simply say so much today. If you need it, you can directly consult our manufacturer.
average method.This measurement method overcomes the problem of steel
Flame cutting and plasma cutting are commonly used for sheet metal blanking in our factory. The equipment used includes manual cutting, copier, semi-automatic cutting machine and NC cutting machine. Manual blanking is arbitrarily large compared to other cuts Flexible and convenient, no special supporting cutting equipment is required.
After, we should prevent the surface damage of the plate. The parts with serious scars must be grinded to make transition, and the wall thickness of the grinded part shall not be less than the design wall thickness. Steel rolling pipe is an unconventional pipe and there is no domestic standard at present. Therefore, the inspection is mainly aimed at the thickness and weld quality.
Have we learned about the packaging process of the steel used? Today, let's discuss the packaging process of lower thick wall coil.
Respect for customers.The pipeline installation sequence is based on the principle of sub area and sub system, with small diameter, from the lower layer to the upper layer, from difficult to easy, from the pipe gallery to the equipment. In principle, the pipeline connected with the machine is configured from the inside to the outside to reduce the impact of welding stress on the installation accuracy of the machine. The interface between indoor and outdoor pipelines shall be left outdoors. Q345B thick wall coiled pipe is a kind of material in carbon steel and is widely used. The thickness of Q345B thick wall coiled pipe is generally more than 10mm, which is widely used in drainage engineering, sewage pipeline, dredging pipeline, construction pipeline, etc. Q345B thick wall coiled pipe is a welded pipe product, and the process in the welded pipe is relatively simple and flexible. This type of steel pipe usually has no inventory and is processed by user. If the quantity is small, the raw materials are not good. The main problem of Q345B thick wall coiled pipe is welding. As long as it is possible, the delivery related requirements can be compared with other products.
Purchasing standards for steel plate coils in the steel market, steel plate coils are popular. What purchasing standards do some users have when purchasing such steel plate coils? The following year old Xiaobian, because steel plate coil plays an important role in construction, railway construction and bridge construction, its quality standards are also more important. If it is for quality solution, we can purchase from these aspects.
It should be noted that in practice, it is difficult to achieve the ideal proportion of metal sand and metal ball in the rinsing agent because the hard and brittle metal sand has a higher crushing rate than the metal ball. For this reason, the mixture should be sampled continuously and the mixed rinse should be tested. According to the particle size distribution, the new rinse agent is added to the cleaning machine, and the amount of metal sand is usually the same in the new rinse agent.
.When the pipe is rolled, the distance between the two welds shall be greater than 100mm, and the distance between the outer wall of the outer branch pipe shall not be less than 50mm.
The distance between the two longitudinal slits of the reel group shall be greater than 100mm. The outer wall of the branch pipe shall be longitudinal, and the circumferential weld shall not be less than 50mm.
The steel plate or strip is bent and then welded to form a thick wall coil. According to the welding form, it is divided into straight seam welded pipe and spiral welded pipe. According to the purpose, it is divided into ordinary welded pipe, galvanized welded pipe, oxygen blowing welded pipe, wire sleeve, metric welded pipe, rolling pipe, deep well pump pipe, automobile pipe, transformer pipe, welded thin-wall pipe, welded pipe and spiral welded pipe. Coil pipe is dedicated to the production of, longitudinal ring coil pipe and steel pressure pipe, and is modified according to similar specifications of traditional rolling equipment. The function of increasing the parameters of spiral steel pipe equipment by 30% fills the gap that the original traditional rolling equipment can not produce. It can produce steel pipes with a diameter of 400 or more and a wall thickness of 8-100mm. The material mainly includes Q235, Q345, 20, 16 manganese capacity, etc. Product executive standards include: GB / t50205-2001 GB / t3092-2001, etc. The products are widely used in petroleum,Q550b thick wall welded pipe, chemicals, natural gas transportation, pile driving, urban water supply, heating, gas supply and other projects. When the coiled pipe is greater than 600mm, and the spacing shall be greater than 200mm.