KalishFixed liKnowledge popularization and superior performance of scissor fork type fixed lifting platform: equipped with safety devices to prevent overloading of the lifting platform; Equipped with a protection valve to prevent hydraulic oil pipe from cracking; Equipped with an emergency lowering device for sudden power failure; The doors of the upper and lower floors are equipped with safety devices that interlock with the system.
To ensure excellent power supply at the installation site, install a separate distribution box. When using the distribution box, the electrical leakage switch must meet the requirements for construction elevators. If the installed construction elevator is variable frequency, the selection of the leakage switch should be compatible with the frequency converter.
Kalish.Many times, after the customer has determined the parameters, the designer will first consider various factors before designing, including the size during transportation, to prevent it from being difficult to transport to the customer's installation site after being too wide. Therefore, during design and manufacturing, it is necessary to consider separate assembly or table split to meet the requirements. At the same time, it is also necessary to consider the bearing capacity of the split, design and manufacture on the premise of ensuring the load capacity and stability and ensure that the equipment can be easily transported, lifted, diesel engine.
.Test the goods elevator every day to see if it can operate normally.
Systems: explosion-proof electronic control system, remote control system, PIC system.
In addition to having a fixed mode, there are also types of mobile elevators. As the name implies, it is a combination of lifting equipment and on-board systems. This type of lifting equipment is very flexible to move, and of course, it is better to use it. For example, there are such lifting equipment in airports, and stations or stadiums may also be equipped with such equipment, as it can be moved by itself, The scope of work is not limited to a certain place, but can be used wherever lifting operations are required. For example, when installing outdoor advertisements, some advertisements are relatively high in height. At this time, mobile lifting equipment can be used to send billboards or staff to a designated height for work. This type of equipment can also be divided into two types according to the driving mode: hydraulic lifting and electric lifting. The so-called hydraulic lifting is the use of hydraulic oil to drive to achieve a specified height. The electric mode is driven by a motor or tooth to lift to a certain height. However, currently, hydraulic lifting platforms are more widely used.
The purpose of hydraulic lifting platform Users can choose the power mode and configuration according to their own scope of use: power systems include: DC power supply, single-phase or three-phase power supply, diesel engine.
How to install and use the bearings of the elevator During the process of installing the bearing device of the elevator, we cannot always ensure that the bearing device has the correct orientation, which inevitably leads to some devices not in place or bearing misalignment. Once these problems occur in the device, and then the inner and outer rings of the bearings cannot be located at the same rotation center. Therefore, when installing bearings,KalishConstruction site personnel lifting cargo elevator, it is necessary to use specialized tools, and in the future, it is also necessary to use a detector to test the bearing device, so as to ensure the success of the bearing device.
The motor winding is short-circuited. When a short circuit fault occurs in the motor winding, the short circuit current is much larger than the normal working current, which increases the copper loss of the winding, causing the winding to overheat or even burn out.
Design brand.Incorrect connection of the elevator motor When a coil, coil group, or one phase winding group is connected inversely it can cause a serious imbalance in the three-phase current and cause the winding to overheat.
Is the water cooling and air cooling of the hydraulic station the same?
Walking: assisted self-propelled, two wheel traction, self driving and car modification.
The brake operators of each mechanism on the equipment should regularly check and adjust the clearance of the brake shoe and brake wheel, ensuring flexibility and reliability. Long term improvement of the elevator factory, a 20 year old brand with competitive prices and guaranteed quality!
install.Several types: motor winding open circuit. When one phase of the motor winding is open circuit, or one of the parallel branches is open circuit, it will cause three-phase current imbalance and cause the motor to overheat.
The transportation lifting platform only needs
After the goods are transported, clean the platform.
Kalish.The brake operators of each mechanism on the equipment should regularly check and adjust the clearance of the brake shoe and brake wheel,Kalish20 ton lifting cargo elevator, ensuring flexibility and reliability. Long term improvement of the elevator factory, a 20 year old brand with competitive prices and guaranteed quality!
It is strictly prohibited for personnel to climb up and down the floors by using the goods elevator privately.
Different. (Specific bearing capacity and lifting height can be designed and customized according to user requirements)