202 stainless 
304ti stainlesStainless steel is more than twice as high and has enough plastic toughness for forming. The wall thickness of storage tank or pressure vessel made of duplex stainless steel is 30-50% less than that of common austenite, which is conducive to reducing the cost.
For the steel pipes bearing fluid pressure, hydraulic test shall be carried out to test their pressure resistance and quality. If there is no leakage under the specified pressure, or they are qualified. Some steel pipes shall also be subject to crimping test, flaring test and flattening test according to the standard or the requirements of the demander.
.Model 420 & mdash& ldquo; Cutting tool level & rdquo; Martensitic steel, an early stainless steel similar to Brinell high chromium steel. It is also used for surgical tools, which can be made very bright. Model 430 & mdash; Ferritic stainless steel for decoration, such as automotive accessories. Good formability, but poor temperature resistance and corrosion resistance.
409— Cheap model (British and American), usually used as automobile exhaust pipe, 1 / 23 / 4h) and other primary and secondary stainless steel coils.
The two ends of the 6m long steel pipe are mechanically cut and the pipe end is relatively sharp to prevent direct contact with the sealing ring of the pipe fitting. It is necessary to cut off a small section at both ends of the pipe or grind off the corner edge with a hand grinder, and then clamp the pipe fittings.
Mold cost: specifications are commonly used but not commonly used. Common specifications are rapid turnover and low mold sharing cost. Because of low utilization and high cost sharing, it is a special enterprise integrating R & D, and service
The thickness of cold rolled steel strip is ultra-thin, and the thickness of hot rolled steel strip is large.
Austenitic stainless steel austenitic stainless steel is developed to overcome the lack of corrosion resistance and brittleness of martensitic stainless steel. The basic composition is crl8% and Ni8%, which is referred to as 18-8 steel for short. Its characteristic is that the carbon content is less than 0.1%, and the single-phase austenite structure is obtained by the combination of Cr and Ni.
At low temperature, coil, timely and cost-effective. It has become the first choice brand for many wire products. Welcome to buy! Ferritic stainless steel tubes have low-temperature brittleness like carbon steel, while austenitic steel does not. Therefore, ferritic or martensitic stainless steels have low-temperature brittleness Austenitic stainless steel or nickel base alloy does not show low temperature brittleness. Sus410 (13Cr),How many stainless steel plates, SUS430 of ferritic stainless steel pipe (18cr) and others show a sharp drop in impact value at low temperature. Therefore, it is necessary to pay special attention when using at low temperature. As a way to improve the impact toughness of ferritic series stainless steel, high purification process can be considered. With the help of grade C and N, when the embrittlement temperature is improved in the range of - 50 ℃ to - 100 ℃, it is possible to use it in freezing related projects Sus430lx (18cr Ti, Nb LC) have been applied to frozen shells. Ferritic stainless steel has a body centered cubic structure. When the material properties become weak, sharp cracks will expand rapidly and cause brittleness. Austenitic stainless steel will not produce brittleness because it has a face centered cubic structure. Austrian stainless steel SUSL (18cr-9ni LC) is used And SUSL (18cr-12ni-2mo-lc) show that they still have superior impact characteristics at low temperature. However, pay attention to the precipitation of ferrite or martensite due to processing, and the tendency of embrittlement due to sensitization and carbide or & sigma; equal heterogeneous precipitation.
safety requirements .HL polishing with appropriate particle size abrasive material to make the surface show continuous grinding lines.
High pressure water jet cutting (professional water cutting: Shanghai Xinwei)
Cold rolled oriented silicon steel strip (sheet) represents: 100 times of DQ + iron loss value (at the frequency of 50Hz, the waveform is sinusoidal, and the magnetic induction peak value is the unit weight iron loss value of 7T) + 100 times of thickness value. Sometimes, G is added after the iron loss value to represent high magnetic induction. For example, dq133 represents cold rolled oriented silicon steel strip (sheet) with iron loss value of 3 and thickness of 0.3mm. Now the new model is 30q133.
·Rotary shaft,304L stainless steel pipe, press roller, blade, impeller, etc. in high-strength corrosion-resistant environment.
resources.Stainless steel pipe will rust? Stainless steel pipe is a food grade stainless steel pipe recognized by the state. It is not absolutely non rusting, but it is not easy to rust compared with other steel grades. Many people will think that the stainless steel pipe is not rusty, especially the stainless steel pipe has high nickel content, which is more difficult to rust. If it is rusty, they will doubt whether it is fake,304 food grade stainless steel pipe, whether it will be replaced by 201 stainless steel pipe, or there is a problem with the raw materials of the steel strip. In fact, these questions and judgments are one-sided views on the lack of understanding of stainless steel pipes. Stainless steel pipes may also produce rust and rust spots under certain conditions.
Bidirectional Product Description: the tensile strength of the material is 980 ~ 1180mpa, and the high working temperature can reach 90 ℃.
Someone asked whether the stainless steel pipe was rusted and caused toxic problems?
.Before connecting the pipe fittings, mark the depth on the pipe first so as to prevent it from being inserted in place and stuck.
Mechanical properties when the steel or sample is stretched, when the stress exceeds the limit even if the stress is no longer increased, the steel or sample continues to have obvious plastic deformation, which is called yield, and the small stress value when the yield phenomenon occurs is the yield point.
Stainless steel pipes are divided into hot rolled, hot drawn and cold drawn (rolled) stainless steel pipes according to the connection and rolling process. According to the difference of stainless steel microstructure, they mainly include semi Ferritic and semi martensitic stainless steel pipes, martensitic stainless steel pipes, austenitic stainless steel pipes, austenitic ferritic stainless steel pipes, etc.