The tensile test is to make q355b into a sample, pull the sample to fracture on the tensile testing machine, and then measure one or more mechanical properties. Usually, only tensile strength, yield strength, elongation after fracture and reduction of area are measured. Tensile test is the basic mechanical property test of metal materials. Almost all metal materials have specified tensile test as long as they have requirements for mechanical properties. Especially for those materials whose shape is not convenient for hardness test,BytcaHow much is a galvanized square tube, tensile test has become the only means to test mechanical properties.
When the square tube is covered, the square tube can be well protected by electrolysis. These are simple ways to prolong the service life of the square tube, We only need to treat according to these, so that the square tube can bring us great help in the use process. The cold galvanized square tube is the principle of cold galvanizing on the square tube used to make the square tube have corrosion performance. Different from hot-dip galvanizing cold galvanizing coating is mainly carried out according to the electrochemical principle. Therefore, it is necessary to ensure the sufficient of zinc powder and steel, so the steel surface treatment requirements are very high.
The cutting surface of the square tube shall be true circle, and the cutting line shall be at right angles to the axis of the square tube. Excessive force is the reason for cutting the square tube into flat or oval, so the square tube should be cut with appropriate force.
.Square pipe is a square steel pipe cold drawn from seamless steel pipe, which is not a straight q355b square pipe, and q355b square pipe, also known as welded pipe, is a square pipe welded by steel plate or strip steel after crimping. Q355b square tube has the advantages of simple production process, high production efficiency, many varieties and specifications and less equipment. The commonly used materials are Q235A and Q235C.
Square tube with complex section: flower shaped square tube, open square tube, corrugated square tube and special-shaped square tube.
Performance index analysis fatigue of square tube the strength, plasticity and hardness discussed above are the indicators of the mechanical properties of metal under static load. In fact, many machine parts work under cyclic load,BytcaGalvanized square pipe and rectangular pipe, under which fatigue will occur.
The inclusions in the square tube treated with calcium can be denatured well, and the morphology of sulfide in the rolled stock is also improved.
Because the green billet can be pressed into any shape, it is easy to weld the square tube into difficult products.
There are some defects in q355b square tube during stretching, which are caused by the following reasons. The common main reasons are as follows: select the appropriate q355b square tube material, and the commonly used materials in austenitic q355b square tube are 1Cr18Ni9Ti and 0Cr18Ni9Ti. During deep drawing, 1Cr18Ni9Ti is more stable than 0Cr18Ni9Ti and has better crack resistance. Therefore, 1Cr18Ni9Ti material should be selected as much as possible.
Product line.Hardness test is to determine the hardness of seamless q355b square pipe by slowly pressing a hard indenter on the sample surface according to the specified conditions, and then testing the indentation depth or size.
Of course, since the q355b square tube material is selected as the base metal, it generally has special purposes, so the welding materials will not be selected casually. It is better to use it according to the welding material manual. If the welding rod manual says that the base metal should be preheated,BytcaSquare pipe with galvanized strip, it should be preheated. Because the welding materials are not used according to the manufacturer's instructions, the weld performance will be greatly reduced.
In order to ensure the stability of the perforation performance and chemical properties of the billet of the square tube, the technical regulations shall be strictly implemented in the operation of the circular furnace, the operation of the heating furnace shall be frequently, the abnormal conditions shall be handled in time and recorded, and the follow-up posts and quality management department shall be notified in time for handling.
The advantage of empty bending is that it can bend the side length when the real bending cannot be carried out, such as synchronous bending and finishing of the upper side and side of q355b square tube. Empty bending can also bend the inner corner of r0.2t without fracture of pipe wall. The disadvantage of empty bending is that when the upper side and side are synchronous empty bending, due to the pressure generated by the upper roll and the lower roll at the same time, the forming force is easy to exceed the critical point, resulting in edge instability and concave and will also affect the stable operation of the unit and forming quality. This is also the different characteristics of q355b square tube and round tube empty bending.
Recommendation and consultation.Cutting: 1 to be fast, no teeth, or whether the cutting line is flat, the starch taste of oil affects the quality of dishes. First choose to cut potatoes with less sharp bottom, so when you cut it's easy to leave the corner of the side end.
The pipeline is only subject to chemical pickling, which can remove oxide scale, rust and old coating. Sometimes it can be used as the reprocessing after sand blasting. Although chemical cleaning can make the surface reach a certain cleanliness and roughness, its anchor lines are shallow and easy to pollute the surrounding environment. The square tube shall be submitted for acceptance in batches, and the batch rules shall comply with the provisions of corresponding product standards.
The painting of the square tube has to go through a process, which requires us to conduct comprehensive consideration and analysis. In particular, the quality and level of the paint and the relevant technical level deserve our attention. Note that the square tube should not be used immediately after painting, but should be placed for a period of time and wait until the paint is dry!
Bytca.In the process of square pipe, we will conduct a variety of tests on it to ensure that the square pipe can be better used in practice. In order to make better use of large-diameter steel pipe, we will continue to innovate. Let's introduce the main elements contained in the lower pipe. For the martensitic chromium square tube, the main elements affecting the are chromium, carbon and molybdenum; For Martensitic chromium nickel square tube, the main influencing elements are nickel, molybdenum, aluminum, cobalt, remove the dirt and grease on the steel surface, and leave a certain space below to facilitate the blowing out of slag. During gas cutting, the movement of the cutting torch shall be kept at a uniform speed. The cutting surface should be 2 ~ 5mm away from the tip of the flame core. If the distance is too close, the cutting will be interrupted easily due to insufficient heat.and if it is too far away