Q355b welded steel pipeProduct desciption

announcer:hp709HP180518493 release time:2022-03-19 19:17:39

After, we should prevent the surface damage of the plate. The parts with serious scars must be grinded to make transition, and the wall thickness of the grinded part shall not be less than the design wall thickness. Steel rolling pipe is an unconventional pipe, and there is no domestic standard at present. Therefore, the inspection is mainly aimed at the thickness and weld quality.

In general, the hot coil pipe is mainly committed to the production of all kinds of circumferential seam and longitudinal ring coils and steel penstocks. It is reformed on the basis of traditional coil equipment and similar specifications and models, so that all parameters of the hot coil pipe can be improved, filling the gap that the original traditional coil equipment can not produce. In addition in terms of processing technology, the hot coil pipe needs attention. The following matters are required: before processing, the hot coil pipe needs to be familiar with the technical requirements of paper, process material properties and other related aspects, select an appropriate hot coil machine, determine whether the cold coil, warm coil or hot coil, and then operate.

.The parts with continuous acoustic flaw detection marks on the weld shall be rechecked by manual ultrasonic and X-ray. If there are defects, after repair, they shall be subject to nondestructive inspection again until it is confirmed that the butt weld of strip steel and the pipe of T-joint intersecting with spiral weld have all passed the X-ray television or film. Each steel plate coil has passed the hydrostatic test, and the pressure adopts radial sealing. The test pressure and time are strictly controlled by the microcomputer detection device of steel plate rolling pipe water pressure. Why are there two longitudinal welds in the same pipe section of rolling pipe?

The quality of steel rolling pipe is greatly affected by the size of weld, mainly including welding process parameters, shape and position parameters of welding wire, flux flow, flux process performance forming joint and other comprehensive factors.

.Finish machining is performed below, and after shot peening the scales on the inner and outer surfaces of the elbow are removed, and both ends are processed with grooves to facilitate welding.

The rolling pipe production technology requires that the rolling pipe weld is a double-sided weld, two longitudinal welds are allowed, and the weld spacing exceeds 300 mm. The welding appearance and quality standard shall not be lower than the level standard in the welding specification.

Steel plate materials mainly include Q235, Q345 20,20# large diameter welded pipe, 45, 35cimo and 42cimo, cold rolled plate can be used for pipe winding. Like oil chemicals, natural gas transportation, piling and urban water supply, heating, and the weld spacing exceeds 300 mm. The welding appearance and quality standard shall not be lower than the level standard in the welding specification.


Q355b welded steel pipeProduct desciption



The distance between the longitudinal joints of two pipes shall be greater than 100 mm. The distance between the outer wall of the branch pipe and the weld shall not be less than 50mm.

The principle of encoder length measurement is to install the encoder on the oil cylinder and roll the large-diameter pipe. The oil cylinder pushes the welded steel pipe to move on the roller table, and the same distance is installed on the series photoelectric switch on the other side. When the oil cylinder pushes the steel pipe and the photoelectric switch at the pipe end, the stroke of the oil cylinder can be converted according to the recorded encoder reading and provided by the large-diameter continuous control manufacturer, so as to calculate the length of the steel pipe.

Generally the wall thickness of coiled pipe is 20mm and the outer diameter is 450-

Discount.Today's equipment is double-sided submerged arc welding, because it goes without saying that double-sided welding is necessary here.

The pipeline installation sequence shall be adopted according to the principle of zoning and subsystem. First the lower level, then the upper level, and then the difficulty. In principle, the pipes connected to the machine are arranged from inside to outside to reduce the impact of welding stress on the installation accuracy of the machine. The joints of indoor and outdoor pipes shall be left outdoors. Q345B thick wall continuous pipe is a widely used carbon steel material. Q345B thick wall continuous pipe with thickness greater than 10mm is widely used in drainage engineering, sewage pipeline, dredging pipeline, construction pipeline, etc. Q345B thick wall continuous pipe is a welded steel pipe product with relatively simple and flexible process. This kind of steel pipe is usually not in stock and is customized. If the quantity is small, the raw materials are not good. The main problem of Q345B thick wall continuous pipe is welding. As long as possible, delivery related requirements can be compared with other products.

Welding voltage because the welding arc is conical, and the welding voltage directly affects the length of the arc. Therefore, the general production process of thick wall continuous pipe can be divided into cold drawing and hot rolling. The production process of cold rolled seamless steel pipe is generally more complex than that of hot rolled steel pipe. First, the pipe must be subject to winding diameter test. If there is no response crack on the surface, the round pipe will be cut and the growth of the blank is about M. However, during annealing, acid should be used for annealing, and attention should be paid to whether there are a large number of bubbles on the surface. If a large number of bubbles appear, the quality of the steel pipe will not meet the response standard. The appearance of cold-rolled seamless steel pipe is shorter than that of hot-rolled seamless steel pipe and the wall thickness is generally smaller than that of hot-rolled seamless steel pipe, but the surface is brighter than that of thick wall seamless steel pipe, the surface is not too rough, the diameter is not too prickly, and the strength is high. The manufacturer offers, operates in good faith, and has a real price. The same specification, thick wall continuous pipe, spot supply, and complete specifications,. With the increase of welding voltage, the moving range of solder joint increases and the molten pool widens. If welding is carried out in a horizontal position, but the edge transition of the weld will not be affected. However, the external welding of spiral welded pipe is carried out on the slope, large-diameter thick wall continuous pipe, thick wall straight seam continuous pipe, steel casing and quality assurance of pipe rolling plant. During the preferential activities, new and old customers are welcome to consult. Therefore, the greater the welding voltage, the wider the weld pool, the more serious the transverse flow of weld metal, and finally lead to the bias of weld metal.


Q355b welded steel pipeProduct desciption



Sealing and sealing shall be carried out in the pipeline. The wall thickness of general coiled pipe is 20mm and the outer diameter is 450-3000mm. The production process of general thick walled coiled pipe can be divided into cold drawing and hot rolling directly from the production process of steel plate rolling and general thick walled coiled pipe. The production process of cold-rolled seamless steel pipe is generally more complex than hot rolling. Roll sizing test shall be carried out for the pipe blank first. If there is no response crack on the surface, the round pipe shall be cut by cutting machine and cut into a blank with a length of about meters. However, when entering the annealing process, acid shall be used for annealing, and attention shall be paid to whether a large number of bubbles are generated on the surface. If a large number of bubbles are generated, it indicates that the quality of steel pipe can not meet the response standard. In appearance, the cold-rolled seamless steel pipe is shorter than the hot-rolled seamless steel pipe, and its wall thickness is generally smaller than that of the hot-rolled seamless steel pipe, but the surface is brighter than that of the thick wall seamless steel pipe. There is not too much roughness on the surface, quotation honest operation, genuine and of the same quality. The thick wall coiled pipe is available from stock, with complete specifications,. Welding, forming, butt joint and pipe rolling, with short processing time, are mainly used for hot-rolled thick wall coils such as pipes, billboard and columns. The thickness of hot-rolled thick wall coils is generally greater than 20mm and the outer diameter is 450-3000mm. The hot-rolled thick wall coils are rolled under the heating of steel plates Welding, forming deburring,Q345B large diameter reel, defect detection and delivery. Sometimes the wall thickness is relatively thick and secondary heating is required. The feature is that the outer diameter tolerance is small Uniform wall thickness. It is important that the hot rolled thick wall coil will not damage the properties of raw materials. The disadvantages of hot roll thick wall rolling pipe are long processing time and. Professional hot-rolled steel pipe, large-diameter thick wall coil, thick wall straight seam coil, steel casing, coil factory inspection is strict, quality assurance. Preferential activities are in progress, welcome to consult. Hot-rolled thick wall coil is widely used: cylinder block, hydraulic pressure, bridge, roller table, etc.

manufacturer.Rolled pipe is divided into straight seam rolled pipe and T-shaped welded pipe. The pipe rolling can meet the market demand for less number and more models of welded pipes. It can be used for pipe pile, column, conveying fluid, pressure vessel, etc. The longitudinal weld of the same barrel section of high pressure and high temperature continuous pipe shall not exceed two courses, and the spacing between the two longitudinal welds shall not be less than 200mm.

Mixed alloy (eutectic mixture): when the liquid alloy solidifies, Qinhuangdao thick wall steel plate coil, the alloy formed by the crystallization of each component of the alloy, such as solder, bismuth cadmium solid melt alloy, and the alloy forming solid solution when the liquid alloy solidifies, such as gold and silver alloy; Many properties of alloys are better than pure metals, so alloys are mostly used in applied materials. The formation of alloys often improves the single element

Main technical measures for low hardening trend

.Thick wall coiled pipe is a kind of familiar steel. It is widely used in construction and pipeline industry because of its durable performance and excellent quality. Have we known about the packaging process of the frequently used steel? With the development of domestic economic situation and the acceleration of welding and casting trend, the advantages of NC cutting are gradually recognized. NC cutting not only greatly improves the rate of plate and product quality, but also improves the working environment and labor efficiency. At present, the NC cutting machines used in the thick wall coil processing industry are mainly flame and ordinary plasma cutting machines, but pure flame cutting can not meet the needs of modern production. At present, most NC cutting machines are NC plasma cutting machines. This type of cutting machine can meet the needs of thick wall coiled pipe plate processing and thick wall coiled pipe parts processing, so the demand will be greater and greater, but there is still a very obvious gap with foreign countries,Q345B large diameter thick wall welded pipe, which is mainly reflected in: 90% of the developed thick wall coiled pipe processing industry is digital control cutting machine, and only 10% is manual cutting; The CNC cutting machine only accounts for part of the total blanking. 10%, of which the proportion of NC plasma cutting is small. Professional hot rolled steel pipe, large diameter thick wall rolling pipe, steel casing, rolling pipe factory to ensure quality, service and quality. Your satisfaction is our pursuit! Welcome to inquire. In industrial production, thick wall coil thermal cutting generally includes gas cutting, plasma cutting, laser cutting, etc. Among them, plasma cutting has a wider cutting range than gas cutting More efficient. Fine plasma cutting technology is close to laser cutting in material cutting surface quality, but the cost is much lower than laser cutting. Therefore, since the successful development of the United States in the mid-1950s, plasma cutting has developed rapidly. With the rapid development of computer and digital technology, NC cutting is also developing, cold rolling and hot rolling. The steel pipes are made of 10, 20, 35 and 45, which are referred to as ordinary steel pipes for short, the steel pipe materials are 27SiMn, 12Cr1MoV, 10crmo9, 15CrMo and 35CrMo, and the stainless steel pipe is collectively referred to as alloy steel pipe. According to the use, it is divided into structural seamless steel pipe; Seamless steel pipe transportation; Seamless steel pipe for boiler; High pressure seamless steel pipe for boiler; High pressure seamless steel pipe for fertilizer equipment; Seamless steel pipe for geological exploration; Jointed steel pipe; Seamless steel pipe for petroleum cracking; Marine seamless steel pipe; Cold drawn cold rolled precision seamless steel pipe; Various alloy pipes.

Compared with seamless steel pipe, thick wall rolling pipe has the disadvantages of low cost, rapid delivery, breaking the fixed specification of seamless steel pipe, etc. Thick wall coiled pipe is made of steel plate or steel strip by bending and then welding. According to the weld form, it is divided into straight welded pipe and spiral welded pipe. According to the purpose, it is divided into general welded pipe, galvanized welded pipe, oxygen blowing welded pipe, wire sleeve, metric welded pipe, idler pipe deep well pump pipe, automobile pipe, transformer pipe, electric welding thin-wall pipe, electric welding special-shaped pipe and spiral welded pipe. Rolling pipe is committed to producing all kinds of rolling pipes and steel penstocks with circumferential seam and longitudinal ring, and is reformed on the basis of similar specifications and models of traditional rolling equipment. The function of improving the parameters of the rolling and welding steel pipe equipment by 30% fills the gap that the original traditional rolling equipment can not produce. It can produce steel pipes with diameter of more than 400 and wall thickness of 8-100mm. Materials mainly include q23 q34 20#, 16 manganese, 16 manganese capacity, etc. Product executive standard: GB / t50205-200, GB / t3092-2001, etc. The products are widely used in petroleum, chemical industry, natural gas transportation, pile driving and urban water supply, heating, gas supply and other projects.